Hasn't this been an option for a long time? I have been doing this at serveral towers.
Kind Regards, David -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Eje Gustafsson Sent: Saturday, June 07, 2003 10:09 PM To: Jeremy Oswalt Subject: Re: [smartBridges] Firmware? As long the ESSID is the same then the frequency don't matter. Best regards, Eje Gustafsson mailto:[EMAIL PROTECTED] The Family Entertainment Network http://www.fament.com Phone : 620-231-7777 Fax : 620-231-4066 - Your Full Time Professionals - eBay UserID : macahan --- searchable smartBridges mailing list archive. http://www.mail-archive.com/smartbridges40part-15.org/ -- JO> Very nice! I assume it doesn't matter if the Airpoints are on different JO> frequencies, right? JO> Jeremy JO> -----Original Message----- JO> From: [EMAIL PROTECTED] JO> [mailto:[EMAIL PROTECTED] On Behalf Of Vasu (sB Tech Team) JO> Sent: Saturday, June 07, 2003 11:33 PM JO> To: [EMAIL PROTECTED] JO> Subject: RE: [smartBridges] Firmware? JO> Hi Marlon, JO> 1. Roaming JO> By enabling the Roaming option, airBridge will associate with the Access JO> Points sharing the same ESSID and can switch in between them JO> automatically. JO> o Select Infrastructure Mode JO> o Uncheck "Select From Available Access Points" option JO> o Enter Valid ESSID JO> o Check Roaming option JO> o Click Set Values button JO> Note that the ESSID will be set to "000000000000" JO> In this Mode, the airBridge can connect to any Access Point with the JO> same ESSID, based on signal strength and can switch in between them if JO> one goes down. In the above Fig. Access Points (Main and Standby) are JO> shown. Both are ON at the time and share same ESSID. airBridge is JO> associated to Main airPoint-PRO. The airBridge has specific settings. JO> The ESSID is same as that of Access Point and BSSID equal to JO> "0000000000000". In case if the Main Access Point goes down, airBridge JO> will reassociate with the Standby Access Point. The switchover time in JO> normally upto 5 secs. This guarantees the internet connection to all the JO> PCs behind airBridge even if one Access Point goes down. JO> Vasu JO> -----Original Message----- JO> From: [EMAIL PROTECTED] JO> [mailto:[EMAIL PROTECTED] On Behalf Of Marlon Schafer JO> (509-982-2181) JO> Sent: Saturday, June 07, 2003 11:07 PM JO> To: '[EMAIL PROTECTED]' JO> Subject: Re: [smartBridges] Firmware? JO> Ooooooooo JO> Tell me about the roaming option! JO> marlon JO> ----- Original Message ----- JO> From: Seeni <mailto:[EMAIL PROTECTED]> JO> To: [EMAIL PROTECTED] JO> Sent: Saturday, June 07, 2003 7:57 AM JO> Subject: RE: [smartBridges] Firmware? JO> Our latest release (5th June 2003) version1.51 for the airBrigde is just JO> an updated version from the March release version. Using with the same JO> firmware again with following improvements. JO> - Roaming option added JO> - Over all improvements in GUI to handle Tab order, Enter Key & ESC key JO> - PPPoE Support (using RASPPPoE Client) JO> - Firmware upgrade across the subnets JO> - Can not login as Administrator with user password JO> - Primary Port (renamed from Primary DHCP Port) JO> Seeni, SB support JO> -----Original Message----- JO> From: [EMAIL PROTECTED] JO> [mailto:[EMAIL PROTECTED] On Behalf Of phantam JO> Sent: Saturday, June 07, 2003 1:54 PM JO> To: '[EMAIL PROTECTED]' JO> Subject: [smartBridges] Firmware? JO> Firmware? Airbridge? AirPoint? JO> Whats up with this or am I just completely dumb, you said new firmware JO> for the units but the 1.51 monitor has the 1.4 firmware it says JO> CD Release ver 1.51 (includes firmware ver 0.01.04) JO> 5 June 2003 JO> CD Release ver 1.5 (includes firmware ver 0.01.04) JO> 3 March 2003 JO> Ok so after 1 full month there are no firmware changes just new buttons? JO> Am I missin something here or am I just loosin my mind? Ok before I get JO> flamed stop yellin at me its just a question. JO> Chris --- [This E-mail scanned for viruses by Declude Virus] The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://198.63.203.6 The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://198.63.203.6
