Yes. Nothing new... Just the "advertisment" for it is new.. ;) Best regards, Eje Gustafsson mailto:[EMAIL PROTECTED] The Family Entertainment Network http://www.fament.com Phone : 620-231-7777 Fax : 620-231-4066 - Your Full Time Professionals - eBay UserID : macahan --- searchable smartBridges mailing list archive. http://www.mail-archive.com/smartbridges40part-15.org/ -- DB> Hasn't this been an option for a long time? I have been doing this at DB> serveral towers.
DB> Kind Regards, DB> David DB> -----Original Message----- DB> From: [EMAIL PROTECTED] DB> [mailto:[EMAIL PROTECTED] Behalf Of Eje Gustafsson DB> Sent: Saturday, June 07, 2003 10:09 PM DB> To: Jeremy Oswalt DB> Subject: Re: [smartBridges] Firmware? DB> As long the ESSID is the same then the frequency don't matter. DB> Best regards, DB> Eje Gustafsson mailto:[EMAIL PROTECTED] DB> The Family Entertainment Network http://www.fament.com DB> Phone : 620-231-7777 Fax : 620-231-4066 DB> - Your Full Time Professionals - DB> eBay UserID : macahan DB> --- DB> searchable smartBridges mailing list archive. DB> http://www.mail-archive.com/smartbridges40part-15.org/ DB> -- JO>> Very nice! I assume it doesn't matter if the Airpoints are on different JO>> frequencies, right? JO>> Jeremy JO>> -----Original Message----- JO>> From: [EMAIL PROTECTED] JO>> [mailto:[EMAIL PROTECTED] On Behalf Of Vasu (sB Tech Team) JO>> Sent: Saturday, June 07, 2003 11:33 PM JO>> To: [EMAIL PROTECTED] JO>> Subject: RE: [smartBridges] Firmware? JO>> Hi Marlon, JO>> 1. Roaming JO>> By enabling the Roaming option, airBridge will associate with the Access JO>> Points sharing the same ESSID and can switch in between them JO>> automatically. JO>> o Select Infrastructure Mode JO>> o Uncheck "Select From Available Access Points" option JO>> o Enter Valid ESSID JO>> o Check Roaming option JO>> o Click Set Values button JO>> Note that the ESSID will be set to "000000000000" JO>> In this Mode, the airBridge can connect to any Access Point with the JO>> same ESSID, based on signal strength and can switch in between them if JO>> one goes down. In the above Fig. Access Points (Main and Standby) are JO>> shown. Both are ON at the time and share same ESSID. airBridge is JO>> associated to Main airPoint-PRO. The airBridge has specific settings. JO>> The ESSID is same as that of Access Point and BSSID equal to JO>> "0000000000000". In case if the Main Access Point goes down, airBridge JO>> will reassociate with the Standby Access Point. The switchover time in JO>> normally upto 5 secs. This guarantees the internet connection to all the JO>> PCs behind airBridge even if one Access Point goes down. JO>> Vasu JO>> -----Original Message----- JO>> From: [EMAIL PROTECTED] JO>> [mailto:[EMAIL PROTECTED] On Behalf Of Marlon Schafer JO>> (509-982-2181) JO>> Sent: Saturday, June 07, 2003 11:07 PM JO>> To: '[EMAIL PROTECTED]' JO>> Subject: Re: [smartBridges] Firmware? JO>> Ooooooooo JO>> Tell me about the roaming option! JO>> marlon JO>> ----- Original Message ----- JO>> From: Seeni <mailto:[EMAIL PROTECTED]> JO>> To: [EMAIL PROTECTED] JO>> Sent: Saturday, June 07, 2003 7:57 AM JO>> Subject: RE: [smartBridges] Firmware? JO>> Our latest release (5th June 2003) version1.51 for the airBrigde is just JO>> an updated version from the March release version. Using with the same JO>> firmware again with following improvements. JO>> - Roaming option added JO>> - Over all improvements in GUI to handle Tab order, Enter Key & ESC key JO>> - PPPoE Support (using RASPPPoE Client) JO>> - Firmware upgrade across the subnets JO>> - Can not login as Administrator with user password JO>> - Primary Port (renamed from Primary DHCP Port) JO>> Seeni, SB support JO>> -----Original Message----- JO>> From: [EMAIL PROTECTED] JO>> [mailto:[EMAIL PROTECTED] On Behalf Of phantam JO>> Sent: Saturday, June 07, 2003 1:54 PM JO>> To: '[EMAIL PROTECTED]' JO>> Subject: [smartBridges] Firmware? JO>> Firmware? Airbridge? AirPoint? JO>> Whats up with this or am I just completely dumb, you said new firmware JO>> for the units but the 1.51 monitor has the 1.4 firmware it says JO>> CD Release ver 1.51 (includes firmware ver 0.01.04) JO>> 5 June 2003 JO>> CD Release ver 1.5 (includes firmware ver 0.01.04) JO>> 3 March 2003 JO>> Ok so after 1 full month there are no firmware changes just new buttons? JO>> Am I missin something here or am I just loosin my mind? Ok before I get JO>> flamed stop yellin at me its just a question. JO>> Chris DB> --- DB> [This E-mail scanned for viruses by Declude Virus] DB> The PART-15.ORG smartBridges Discussion List DB> To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe DB> smartBridges <yournickname> DB> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe DB> smartBridges) DB> Archives: http://198.63.203.6 DB> The PART-15.ORG smartBridges Discussion List DB> To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> DB> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) DB> Archives: http://198.63.203.6 DB> --- DB> [This E-mail scanned for viruses by Declude Virus] --- [This E-mail scanned for viruses by Declude Virus] The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://198.63.203.6
