Sure you can. Cross polarize your system..... Also, reducing the antenna power (receive capability) will often do wonders.
People's first reaction is to try to blow right through it rather than top toe through. In cars, there's no way to have too much power. In radio most run too much. marlon ----- Original Message ----- From: "George" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Wednesday, July 30, 2003 10:57 PM Subject: Re: [smartBridges] up down link quality with appo troubleshooting question > Just noticing in the site survey pane, Seems like a lot of crowding in > there. Seems almost all the channels have an ap siting on it. > That can't help > George > > ----- Original Message ----- > From: "dennys" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Wednesday, July 30, 2003 7:47 PM > Subject: [smartBridges] up down link quality with appo troubleshooting > question > > > > our Wireless (in site 1) > > Antenna : Klinkert Unidirectional 24 dBi > > Type : APPO > > Firmware : 1.4j.8 > > APPO Power : 17.5 dBm > > Cable Lost : 2 dBm > > ESSID : JAM-SHD > > Operational Mode : Client Bridge > > IP : 10.99.88.1 > > Regulatory : MKK1 > > Channel : 4 --> the best ping we get if we use this channel different than > Parent > > RTS/CTS : 2437 > > Preamble : Short > > Other Setting : default > > > > our Wireless (in site 2) > > Antenna : Klinkert Unidirectional 24 dBi > > Type : APPO > > Firmware : 1.4j.8 > > APPO Power : 17.5 dBm > > Cable Lost : 2 dBm > > ESSID : JAM-SHD > > Operational Mode : Access Point > > IP : 10.99.88.2 > > Regulatory : MKK1 > > Channel : 14 > > RTS/CTS : 2437 > > Preamble : Short > > Other Setting : default > > > > Distance between 2 our wireless +/- 3 Km > > Another wireless detected by our Site 1 +/- 8 Wireless > > > > Question : > > 1. why our link quality up down and not stable ? > > 2. how can we make it more stable ? > > 3. is our wireless link quality interference with other wireless ? > > 4. why our wireless in site 1 (client bridge mode) detect another > > good link quality from neighbour wireless except that parent > > wireless in site 2 ? > > 5. is link quality up down as shown in graphic will stable if we > > use amplifier ? > > 6. if we must add amplifier, can we just at it in our parent wireless > > in site 2 ? > > > > thank's for your help, because we want to make it more stable and we > > are very very very interest to use your smartBridges product for all > > our WISP enviroment... (middle cheap, good range, and bad up down link > > quality,plese help us to fix it) > > > > regards > > dennys > > ------- End of Forwarded Message ------- > > > > > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) > Archives: http://archives.part-15.org > The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org
