Where or what do you mean doing routing? I have the setup like this T-1 to >bandwidth unit to switch which feeds a Motorola AP unit sending backhaul to tower at tower I have another Motorola unit receiving the backhaul feeding to a switch then to two APPO's North and south. Where would you suggest I put in routing??
----- Original Message ----- From: "Eje Gustafsson" <[EMAIL PROTECTED]> To: "Blazen Wireless" <[EMAIL PROTECTED]> Sent: Thursday, August 14, 2003 9:00 PM Subject: Re: [smartBridges] APPO furstrations.. You need a bandwidth manager on your network and bandwidth limit your clients. Plus if your doing a completely bridge network then you seriously needs to start doing some routing on your network or else things will not work. Best regards, Eje Gustafsson mailto:[EMAIL PROTECTED] The Family Entertainment Network http://www.fament.com Phone : 620-231-7777 Fax : 620-231-4066 - Your Full Time Professionals - eBay UserID : macahan --- searchable smartBridges mailing list archive. http://www.mail-archive.com/smartbridges40part-15.org/ -- BW> Okay guys here is a question I know SB says they can have up to 128 clients associated to the APPO. I have aprox 22 on each one and they are totally crapping out by that mean I get 4-5 users on BW> downloading at any given time and I swear to you pings just go to hell as high as 200-300 and lows about 30ms. I have tried EVERYTHING RTS CTS different channels WEP no WEP anything and BW> everything and it has got me by the balls and I am tired of clients calling me complaining it is slow. It used to be awesome with 4-5 users total on it and even 10 users but after that its just BW> gone down hill. BW> Any suggestion would GREATLY be appreciated. BW> two APPO's each connected to a 500mw Amp 50 ft of coax LMR 400 and then to a 13DB 90* pac wireless ant one facing north and one facing south both on chan 3 I know I know you will say interference BW> from each other I tried separating and it made no difference it actually got worse I even had one appo in client bridge mode to check interference and I saw nothing form the APPO right next to it BW> and very few other Access points out in the field. Most were at rssi 20 maybe 30% and link 20%. BW> PLEASE PLEASE PLEASE help me with any ideas I am all out I have worked on this all week I have a remote pop that is fed by the main two APPO's and the two customers on that radio can ping the BW> remote appo all day long with less then 5 ms yet when you try and ping the main appos the pings are all over the place.. BW> Oh yea most all signals at eh APPO's from the client show (not sure how accurate) 80 -100 RSSI some just under 80% and link about the same so I don't know if this could hamper it I have tried BW> with a couple clients setting the APPO and ABO to autofallback speeds and that seemed to help for a couple people that were far out about 4-5 miles people up close seem to be fine.. BW> 13-19db ants on each install BW> HELPPPPPPPPPPPPPPPPPPP BW> Martin -- [This E-mail scanned for viruses by Declude Virus] The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org
