Hi Steve...and wobbler fans...

Wobblers are neat in that for a folk like me I can make a steam 
engine for little money and without a lathe...well sort of without a 
lathe!!!

Most of my wobblers I make from K&S brass tube...it is allready round 
and has a hole down the middle!

Not making light of having a proper lathe...I would love to have one!

The pistons that I make up are of 3/8" or 1/2"  brass rodding that I 
found scrap some where...a couple of feet of it has lasted me 20 
years of building with lots left for another 20 years if I can be so 
lucky. I made one tiny wobbler single acting from 3/16" brass 
rod...drilled and lapped on my verticle table drill...sort of a poor 
mans lathe.

My modeling budjet or lack of one has put me on a path of doing 
things on the cheap...finding old Mamod cylinders fo me is like 
finding gold. Lots of folks have upgraded to IP and I have been able 
to accquire the Mamod discards. Mamod cylinders are quite well 
thought out... Inside is a very smart piece of engineering...not like 
the early Mamod stationary engines with a solid piston...and if you 
were lucky a grove had been machined in it to act like a seal.

Most early Mamod stationary engines with their low pressure boilers 
(12lbs) relied on the fact that their was lots of condesed water in 
the steam...the water would get into the grove and help with cylinder 
sealing...in fact putting nice dry steam into them made them run 
worse.

The Mamod piston is spring loaded on it's rod...with a couple of 
little seals front and back...this lets the piston "float" in the 
cylinder and self center...rather cool when you want to mass produce 
a prescion assembly without having to lap etc...

A fairly new producer of steam motors have taken the lowly wobbler to 
new levels...Chedder aside... the new wobblers from SVS are little 
jewels. I am attaching a couple of pictures of the steam motor and a 
small tram "Lucy" that I was commissioned to make. The SVS is 
TINY...the whole motor with reduction drive fits into a 30 by 40mm 
cube...another commission I am working on will use one in an "O" 
scale 2P british outline live steam...the boiler will be gas/butane 
fired internal Belpar with a grate suitable for real coal...90% of 
the heat will be from the Butane...the coal will provide a little of 
the heat but 100% of real coal smoke...sort of cheating but a scale 
"O" scale fire box is only 20 by 30mm...with a fire box door about as 
big around as your thumb!

A single acting wobbler with a decent flywheel will pull a 20LB train 
that I mentioned in another eMail...because the cylinder is single 
acting and because there is only the ONE cylinder the motor it uses 
1/4 the amount of a steam motor that has TWO double acting IP 
cylinders...!

There is another wonderful thing that a single acting wobbler can do 
that a slide valve cylinder can't! ...at least in the model sizes 
that we deal with as in Roundhouse/Accucraft etc ...is that when a 
wobbler cylinder runs fast you start to get steam cut off...'cause 
the cylinder cannot fill fully on its power stroke...that is the 
cylinder is moving accross the port so quicly that there is not 
enough time for it to fill properly ...neat huh!

This takes us into a whole new realm of wobblers that is the size of 
the steam inlet port and it's shape...for those who have not fallen 
to sleep by now...ya I really like wobblers cause you can do a lot of 
experimentation with them that you can't withe slide valve.

I have tried different hole sizes and shapes and get wonderful 
results...I can tailor the steam motor to the expected power and 
speed of the finished model. Besides the inlet and outlet sizes the 
timing of wobblers can drastically change the power and speed of them 
to...that is the spacing of the steam ports in the block have a major 
impact into the speed of the motor...just like timing an electric 
motor by changing the position of the comutator...these steam motors 
can be timmed...

Thats enough for tonight a lot to take in...I hope along the line 
some one will get some help for their sick wobblers...

...Steve we will get there...lots to try yet...Tony
_______________________________________________
SSLiveSteam mailing list
Send messages: [email protected]
Cancel subscription: http://postfix.45mm.com/mailman/listinfo/sslivesteam
Rules: http://www.45mm.com/sslivesteam_guide.html

Reply via email to