<additional> <edgeData id="example" file="edgedata_test.xml" begin="23400" end="40000"/> </additional>
Am Mo., 12. Juni 2023 um 13:23 Uhr schrieb 渡邊勇志 <yuyujiji0...@gmail.com>: > Thank you for your response. I tried loading the additional XML into my > .sumocfg file, but the "begin" attribute of the Edge data became 0. The > contents of the additional xml are written as follows: > > "Additional.xml" > <additional> > <time> > <begin value="23400"/> > <end value="40000"/> > </time> > </additional> > > I apologize if this is a basic question, but how can I specify a time > range in the output data using the contents of the additional xml? > Could you please provide guidance on this matter? > > Sincerely, > Yuji > > 2023年6月12日(月) 16:24 Jakob Erdmann <namdre.s...@gmail.com>: > >> Hello, >> the option **--edgedata-output** does not support a custom time range. To >> set a custom time range you need to define the edgeData output with 'begin' >> and 'end' attributes in an additional xml file and load this file in your >> .sumocfg. >> See >> https://sumo.dlr.de/docs/Simulation/Output/Lane-_or_Edge-based_Traffic_Measures.html#instantiating_within_the_simulation >> >> Am Mo., 12. Juni 2023 um 08:59 Uhr schrieb 渡邊勇志 <yuyujiji0...@gmail.com>: >> >>> Hello, >>> >>> I hope this email finds you well. I am writing to seek assistance >>> regarding an issue I encountered while using the Sumo simulation tool. >>> >>> I successfully generated an edge-based state dump output by entering the >>> command "--edgedata-output <FILE>" in the command line. The output was >>> produced correctly. However, when I attempted to output data for a specific >>> time range by specifying the time using the additional attributes -b >>> (--begin) and -e (--end), the results were not as expected. I noticed that >>> setting the begin parameter to 0 resulted in the correct output, but I >>> require the output for the specified time range. >>> >>> I would greatly appreciate it if you could provide guidance on how to >>> correctly output the data when the begin parameter is set to a value other >>> than 0, ensuring that it corresponds to the desired time range. >>> >>> <!-- generated on 2023-06-12 15:33:24 by Eclipse SUMO sumo Version >>> 1.16.0 <configuration xmlns:xsi=" >>> http://www.w3.org/2001/XMLSchema-instance" >>> xsi:noNamespaceSchemaLocation=" >>> http://sumo.dlr.de/xsd/sumoConfiguration.xsd"> <input> <net-file >>> value="manhattan.net.xml"/> <route-files value="sumotest.trips.xml"/> >>> </input> <output> <edgedata-output value="edge_test.xml"/> </output> <time> >>> <begin value="34000"/> </time> <report> <no-step-log value="true"/> >>> </report> </configuration> --> >>> <meandata xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" >>> xsi:noNamespaceSchemaLocation="http://sumo.dlr.de/xsd/meandata_file.xsd" >>> > </meandata> >>> >>> Thank you for your attention to this matter. I look forward to your >>> prompt response. >>> >>> Yours sincerely, >>> >>> Yuji >>> >>> >>> >>> _______________________________________________ >>> sumo-dev mailing list >>> sumo-dev@eclipse.org >>> To unsubscribe from this list, visit >>> https://www.eclipse.org/mailman/listinfo/sumo-dev >>> >> _______________________________________________ >> sumo-dev mailing list >> sumo-dev@eclipse.org >> To unsubscribe from this list, visit >> https://www.eclipse.org/mailman/listinfo/sumo-dev >> > _______________________________________________ > sumo-dev mailing list > sumo-dev@eclipse.org > To unsubscribe from this list, visit > https://www.eclipse.org/mailman/listinfo/sumo-dev >
_______________________________________________ sumo-dev mailing list sumo-dev@eclipse.org To unsubscribe from this list, visit https://www.eclipse.org/mailman/listinfo/sumo-dev