I did it! I am truly thankful. Yuji
2023年6月12日(月) 21:32 Jakob Erdmann <namdre.s...@gmail.com>: > <additional> > <edgeData id="example" file="edgedata_test.xml" begin="23400" > end="40000"/> > </additional> > > Am Mo., 12. Juni 2023 um 13:23 Uhr schrieb 渡邊勇志 <yuyujiji0...@gmail.com>: > >> Thank you for your response. I tried loading the additional XML into my >> .sumocfg file, but the "begin" attribute of the Edge data became 0. The >> contents of the additional xml are written as follows: >> >> "Additional.xml" >> <additional> >> <time> >> <begin value="23400"/> >> <end value="40000"/> >> </time> >> </additional> >> >> I apologize if this is a basic question, but how can I specify a time >> range in the output data using the contents of the additional xml? >> Could you please provide guidance on this matter? >> >> Sincerely, >> Yuji >> >> 2023年6月12日(月) 16:24 Jakob Erdmann <namdre.s...@gmail.com>: >> >>> Hello, >>> the option **--edgedata-output** does not support a custom time range. >>> To set a custom time range you need to define the edgeData output with >>> 'begin' and 'end' attributes in an additional xml file and load this file >>> in your .sumocfg. >>> See >>> https://sumo.dlr.de/docs/Simulation/Output/Lane-_or_Edge-based_Traffic_Measures.html#instantiating_within_the_simulation >>> >>> Am Mo., 12. Juni 2023 um 08:59 Uhr schrieb 渡邊勇志 <yuyujiji0...@gmail.com >>> >: >>> >>>> Hello, >>>> >>>> I hope this email finds you well. I am writing to seek assistance >>>> regarding an issue I encountered while using the Sumo simulation tool. >>>> >>>> I successfully generated an edge-based state dump output by entering >>>> the command "--edgedata-output <FILE>" in the command line. The output was >>>> produced correctly. However, when I attempted to output data for a specific >>>> time range by specifying the time using the additional attributes -b >>>> (--begin) and -e (--end), the results were not as expected. I noticed that >>>> setting the begin parameter to 0 resulted in the correct output, but I >>>> require the output for the specified time range. >>>> >>>> I would greatly appreciate it if you could provide guidance on how to >>>> correctly output the data when the begin parameter is set to a value other >>>> than 0, ensuring that it corresponds to the desired time range. >>>> >>>> <!-- generated on 2023-06-12 15:33:24 by Eclipse SUMO sumo Version >>>> 1.16.0 <configuration xmlns:xsi=" >>>> http://www.w3.org/2001/XMLSchema-instance" >>>> xsi:noNamespaceSchemaLocation=" >>>> http://sumo.dlr.de/xsd/sumoConfiguration.xsd"> <input> <net-file >>>> value="manhattan.net.xml"/> <route-files value="sumotest.trips.xml"/> >>>> </input> <output> <edgedata-output value="edge_test.xml"/> </output> <time> >>>> <begin value="34000"/> </time> <report> <no-step-log value="true"/> >>>> </report> </configuration> --> >>>> <meandata xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" >>>> xsi:noNamespaceSchemaLocation="http://sumo.dlr.de/xsd/meandata_file.xsd >>>> "> </meandata> >>>> >>>> Thank you for your attention to this matter. I look forward to your >>>> prompt response. >>>> >>>> Yours sincerely, >>>> >>>> Yuji >>>> >>>> >>>> >>>> _______________________________________________ >>>> sumo-dev mailing list >>>> sumo-dev@eclipse.org >>>> To unsubscribe from this list, visit >>>> https://www.eclipse.org/mailman/listinfo/sumo-dev >>>> >>> _______________________________________________ >>> sumo-dev mailing list >>> sumo-dev@eclipse.org >>> To unsubscribe from this list, visit >>> https://www.eclipse.org/mailman/listinfo/sumo-dev >>> >> _______________________________________________ >> sumo-dev mailing list >> sumo-dev@eclipse.org >> To unsubscribe from this list, visit >> https://www.eclipse.org/mailman/listinfo/sumo-dev >> > _______________________________________________ > sumo-dev mailing list > sumo-dev@eclipse.org > To unsubscribe from this list, visit > https://www.eclipse.org/mailman/listinfo/sumo-dev >
_______________________________________________ sumo-dev mailing list sumo-dev@eclipse.org To unsubscribe from this list, visit https://www.eclipse.org/mailman/listinfo/sumo-dev