ok, here is log from camera boot ETRAX FS NAND boot loader
========================= Rev 1, Nov 23 2009 12:31:43 Boot config: 0x00040000->0x40440000, len 0x00200000, boot @ 0x40440000 CPU revision: 0x00000020 Bootloader main at 0x38000ce2 Data end: 0x3800573c Bss: 0x38008000 Heap: 0x38008000 Identifying nand chip... maf_id: 0x00000020; dev_id: 0x000000f1 mtd->size == 0x08000000 scan_bbt(); mtd->size == 0x08000000 scan_bbt() ...01; mtd->size == 0x08000000 len == 0x00000100; and BBT_LEN_1 == 0x00000400 scan_bbt() ...02; mtd->size == 0x08000000 scan_bbt() ...03; mtd->size == 0x08000000 scan_bbt() ...1; mtd->size == 0x08000000 scan_bbt() ...2; mtd->size == 0x08000000 scan_bbt() search_read_bbts(); mtd->size == 0x08000000 search_read_bbts() search primary table; mtd->size == 0x08000000 search_bbt() ...1; mtd->size == 0x08000000 search_bbt() ...2; maxblocks: 0x00000004; mtd->size == 0x08000000 Block: 0x000003ff Check, if we found a bbt for each requested chip Bad block table found at page0x0000ffc0, version 0x00000001 search_read_bbts() search mirror table search_bbt() ...1; mtd->size == 0x08000000 search_bbt() ...2; maxblocks: 0x00000004; mtd->size == 0x08000000 Block: 0x000003ff Block: 0x000003fe Check, if we found a bbt for each requested chip Bad block table found at page0x0000ff80, version 0x00000001 scan_bbt() ...3 Done. Chip identified... 3; NAND 128MiB 3,3V 8-bit type: 0x00000004 flags: 0x000000c5 size: 0x08000000 erasesize: 0x00020000 oobblock: 0x00000800 oobsize: 0x00000040 ecctype: 0x00000002 eccsize: 0x00000100 Oob info: useecc: 0x00000002 eccbytes: 0x00000018 eccpos: 0x00000028 0x00000029 0x0000002a 0x0000002b 0x0000002c 0x0000002d 0x0000002e 0x0000002f 0x00000030 0x00000031 0x00000032 0x00000033 0x00000034 0x00000035 0x00000036 0x00000037 0x00000038 0x00000039 0x0000003a 0x0000003b 0x0000003c 0x0000003d 0x0000003e 0x0000003f Bootload in progress... New block 0x00040000;len: 0x00200000;start: 0x00040000 New block 0x00060000;len: 0x001e0000;start: 0x00060000 New block 0x00080000;len: 0x001c0000;start: 0x00080000 New block 0x000a0000;len: 0x001a0000;start: 0x000a0000 New block 0x000c0000;len: 0x00180000;start: 0x000c0000 New block 0x000e0000;len: 0x00160000;start: 0x000e0000 New block 0x00100000;len: 0x00140000;start: 0x00100000 New block 0x00120000;len: 0x00120000;start: 0x00120000 New block 0x00140000;len: 0x00100000;start: 0x00140000 New block 0x00160000;len: 0x000e0000;start: 0x00160000 New block 0x00180000;len: 0x000c0000;start: 0x00180000 New block 0x001a0000;len: 0x000a0000;start: 0x001a0000 New block 0x001c0000;len: 0x00080000;start: 0x001c0000 New block 0x001e0000;len: 0x00060000;start: 0x001e0000 New block 0x00200000;len: 0x00040000;start: 0x00200000 New block 0x00220000;len: 0x00020000;start: 0x00220000 complete, status 0x00000000, loaded 0x00200000 bytes Data in DRAM: 0x25f005b0 0x009cedff 0xbeef05b0 Booting... Uncompressing Linux... Done. Now booting the kernel. Linux version 2.6.19 (oleg@eyesisboxus) (gcc version 3.2.1 Axis release R64/1.64) #2 Sun Jan 15 18:43:42 MST 2012 Setting up paging and the MMU. Linux/CRISv32 port on ETRAX FS (C) 2003, 2004 Axis Communications AB Built 1 zonelists. Total pages: 8160 Kernel command line: root=/dev/mtdblock3 init=/linuxrc rootfstype=jffs2 PID hash table entries: 256 (order: 8, 1024 bytes) Dentry cache hash table entries: 8192 (order: 2, 32768 bytes) Inode-cache hash table entries: 4096 (order: 1, 16384 bytes) Memory: 40304k/65536k available (1744k kernel code, 25232k reserved, 622k data, 72k init) Mount-cache hash table entries: 1024 NET: Registered protocol family 16 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 512 (order: -2, 2048 bytes) TCP established hash table entries: 2048 (order: 0, 8192 bytes) TCP bind hash table entries: 1024 (order: -1, 4096 bytes) TCP: Hash tables configured (established 2048 bind 1024) TCP reno registered Check hardware configuration of Elphel 353 camera Elphel 10349/10369 IO extension board is present fast_timer_init() JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. io scheduler noop registered (default) Serial: CRISv32 driver $Revision: 1.78 $ <6>ttyS0 at I/O 0xb0026000 (irq = 68) is a CRISv32 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize PPP generic driver version 2.4.2 ETRAX FS 10/100MBit ethernet v0.01 (c) 2003 Axis Communications AB eth0: changed MAC to 00:40:8C:CD:00:00 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx ide: ETRAX FS built-in ATA DMA controller cris_ide_init() hda: TOSHIBA MK1231GAL, ATA DISK drive Physical sector 4096 bytes Updating sector size to match that of a hard drive: 4096 ide0 at 0x10000000-0x10000007,0x2c000000 on irq 65 hda: max request size: 128KiB hda: 234441648 sectors (120034 MB), CHS=16383/255/63, (U)DMA Skipping WIN_SPECIFY for large sectors drive, it is useless here and likely not supported Skipping WIN_SPECIFY for large sectors drive, it is useless here and likely not supported hda: cache flushes supported hda: hda1 Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial drivers/usb/serial/usb-serial.c: USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic drivers/usb/serial/usb-serial.c: USB Serial Driver core drivers/usb/serial/usb-serial.c: USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter usbcore: registered new interface driver belkin drivers/usb/serial/belkin_sa.c: USB Belkin Serial converter driver v1.2 drivers/usb/serial/usb-serial.c: USB Serial support registered for cp2101 usbcore: registered new interface driver cp2101 drivers/usb/serial/cp2101.c: Silicon Labs CP2101/CP2102 RS232 serial adaptor driver v0.07 drivers/usb/serial/usb-serial.c: USB Serial support registered for Garmin GPS usb/tty usbcore: registered new interface driver garmin_gps drivers/usb/serial/garmin_gps.c: garmin gps driver v0.28 drivers/usb/serial/usb-serial.c: USB Serial support registered for MCT U232 usbcore: registered new interface driver mct_u232 drivers/usb/serial/mct_u232.c: Magic Control Technology USB-RS232 converter driver z2.0 drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303 usbcore: registered new interface driver pl2303 drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver ETRAX FS stream co-processor driver v0.01, (c) 2003 Axis Communications AB stream co-processor: init done. axisflashmap: ... NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit) Additional Info: ID byte3=0x0, byte4=0x1d Flash is rated 30 ns, modifying bif_core_rw_grp3: old=0x6300483, new=0x6300001 NAND 128MiB 3,3V 8-bit: 0x08000000 bytes of NAND flash memory. axisflashmap: Set to boot from NAND flash, making NAND flash primary device. axisflashmap: flash read 512 bytes at 0x00040000, data: 00 b0 05 f0 25 ff ed 9c axisflashmap: partition table offset 10, data: ef be 84 00 12 0f 00 00 axisflashmap: Found a valid partition table at 0xc03019ae-0xc0301a3a. offset == 0x00040000, size == 0x007C0000 offset == 0x00800000, size == 0x01800000 offset == 0x02000000, size == 0x05000000 offset == 0x07000000, size == 0x00C00000 Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit": 0x00000000-0x08000000 : "main" Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit": 0x00000000-0x00040000 : "part0" Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit": 0x00040000-0x00800000 : "part1" Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit": 0x00800000-0x02000000 : "part2" Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit": 0x02000000-0x07000000 : "part3" Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit": 0x07000000-0x07c00000 : "part4" ETRAX FS GPIO driver v2.5, (c) 2003-2006 Axis Communications AB Elphel (R) model 353 FPGA (Xilinx (R) XC3S1200E) configuration driver - 132 Elphel (R) model 353 system clocks (PLL frequency synth.) driver - 133 fpga_control- 129 arch/cris/arch-v32/drivers/elphel/framepars.c:390:initGlobalPars GLOBALPARS(G_DEBUG)=0 arch/cris/arch-v32/drivers/elphel/framepars.c:420:initMultiPars GLOBALPARS(G_MULTI_NUM)=0 Elphel (R) Model 353 Frame Parameters device driver - 130 Elphel FPGA interrupts initialized Initializing DMA registers for EXTDMA3 - Elphel (R) Model 353 Camera Driver - 126 Elphel (R) model 353 i2c character device driver - 134, 2 channels Raw image access driver- 131 Elphel (R) Model 353 video buffer device driver- 135 Elphel (R) model 353 Exif device driver - 125 Starting Elphel (R) Model 353 Gamma Tables device driver - 137 Elphel (R) Model 353 Gamma Tables device driver - 137 Elphel (R) Model 353 Histograms device driver imu_logger- 141 TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 VFS: Mounted root (jffs2 filesystem) readonly. Freeing unused kernel memory: 72k freed /linuxrc: Mounting /mnt/flash... Empty flash at 0x00b7e238 ends at 0x00b7e800 Empty flash at 0x01b46038 ends at 0x01b46800 Empty flash at 0x01b5e544 ends at 0x01b5e800 done /linuxrc: Starting init. init: starting up. Starting system initialization. Axis Linux, http://developer.axis.com/ Copyright (C) 2000-2007 Axis Communications AB Elphel (R) Model 353 Camera release 8.1.2 * Mounting filesystems... [ ok ] * Initializing /var... [ ok ] * Determining MAC address... + using saved MAC address: 00:0E:64:08:19:B0 [ ok ] * Initializing random number generator... [ ok ] * Setting hostname... + hostname: "Elphel353" [ ok ] * Initializing volatile resolver configuration... [ ok ] * Setting FPGA master clock to 160 MHz... [ ok ] * Programming FPGA with /etc/x353.bit... [ ok ] * Loaded FPGA rev... [ 353402b ] * Adjusting DDR SDRAM clock phase... [ PH 90/24 ] * Turn on xtall output (12MHz) to FPGA... [ ok ] * Some CMOS-based sensor board attached... [ assuming 10338 ] * Configure broadcast ping... [ ok ] System initialization is done. /bin/sh: can't access tty; job control turned off # New runlevel: 3 * Starting respawn daemon... [ ok ] * Starting system and kernel logger... Jan 1 00:00:18 Elphel353 syslogd 1.4.1: restart. + system logger started + kernel logger started [ ok ] * Bringing lo up... [ ok ] * Bringing eth0 up... eth0: changed MAC to 00:0E:64:08:19:B0 + hardware address: 00:0E:64:08:19:B0 + media: auto + eth0 going up eth0: changed MAC to 00:0E:64:08:19:B0 + IPv4 on eth0 + boot protocol: none + IP address: 192.168.0.9 + netmask: 255.255.255.0 + broadcast address: 192.168.0.255 + default IPv4 gateway: 192.168.0.15 + set MDI to MDI (normal) mode y + done [ ok ] * Waiting for a network interface... + eth0 is up [ ok ] * Starting ipsetd... Jan 1 00:00:20 Elphel353 ipsetd[709]: Timeout in 120 s. Jan 1 00:00:20 Elphel353 ipsetd[709]: Expecting echo request payload 408 bytes. Jan 1 00:00:20 Elphel353 ipsetd[709]: On echo request arrival, execute /etc/ipsetd.script. [ ok ] * Starting telnet server... telnetd: starting port: 23; interface: any; login program: /bin/login; maximum number of allowed simultaneous clients: unlimited [ ok ] * Starting ftp server... Jan 1 00:00:20 Elphel353 vftpd[715]: Starting vftpd 0.01 Jan 1 00:00:20 Elphel353 vftpd[716]: qos_setup_socket: unsupported AF [ ok ] * Starting ssh server... Jan 1 00:00:21 Elphel353 dropbear[727]: Running in background [ ok ] * Starting mii-diag... [ ok ] * Starting image server on port 8081, making Exif... [ ok ] * Flushing JFFS2 (sync)... [ ok ] * Starting autocampars daemon... [ ok ] * Starting autoexposure daemon... autoexposure started, daemon_bit=0x0, debug=0x1 autoexposure.c:126:main: autoexposure started, daemon_bit=0x0, debug=0x1 [ ok ] * Starting ccamftp daemon... [ ok ] * initializing camera/sensor parameters... arch/cris/arch-v32/drivers/elphel/framepars.c:390:initGlobalPars GLOBALPARS(G_DEBUG)=0 initSequencers:resetting both sequencers arch/cris/arch-v32/drivers/elphel/framepars.c:420:initMultiPars GLOBALPARS(G_MULTI_NUM)=0 sensor clock set to 20000000 removing MRST from the sensor Found MT9P001 2592x1944 sensor, chip ID=1801 trying MT9P001 Resetting MT9X001 sensor Reading sensor registers to the shadows: Initializing MT9X001 registers with default values: Starting hardware sequencers [ ok ] * Starting lighttpd web server... [ ok ] * Setting time from NTP server... [ unavailable ] * Looking for I/O board... [ 10369"A" ] ETRAX FS IOP USB Host Controller version 1.10 (c) 2004, 2005, 2006 Axis Communications AB crisv32_hc crisv32_hc.0: ETRAX FS IOP USB Host Controller crisv32_hc crisv32_hc.0: new USB bus registered, assigned bus number 1 crisv32_hc crisv32_hc.0: irq 51, io base 0x00000000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected crisv32_hc crisv32_hc.0: ETRAX FS IOP USB Host Controller usbcore: registered new interface driver snd-usb-audio usbcore: registered new interface driver snd-usb-caiaq * Initializing USB hub... [ ok ] * Setting system time from CMOS clock... usb 1-1: new full speed USB device using crisv32_hc and address 2 usb 1-1: configuration #1 chosen from 1 choice hub 1-1:1.0: USB hub found hub 1-1:1.0: 4 ports detected [ Fri May 18 21:41:48 UTC 2012 ] * Starting video streamer... [ ok ] * Starting IMU/GPS/compass... [ none ] launcher: nothing to launch All scripts for runlevel 3 done in 89.71s. May 18 21:42:51 Elphel353 ipsetd[709]: Timed out after 120s. ####################################################################################################################################### and now top just after boot Mem: 24440K used, 15936K free, 0K shrd, 0K buff, 14808K cached CPU: 0% usr 0% sys 0% nic 99% idle 0% io 0% irq 0% sirq Load average: 0.21 0.15 0.09 2/34 860 PID PPID USER STAT VSZ %MEM %CPU COMMAND 860 854 root R 1496 4% 0% top 751 1 root S 4136 10% 0% /usr/local/sbin/autoexposure 827 1 root S 44912 111% 0% /usr/local/bin/str 829 827 root S 44912 111% 0% /usr/local/bin/str 830 829 root S 44912 111% 0% /usr/local/bin/str 763 759 root S 30872 76% 0% /usr/local/sbin/php 764 763 root S 30872 76% 0% /usr/local/sbin/php 765 763 root S 30872 76% 0% /usr/local/sbin/php 759 1 root S 4976 12% 0% /usr/local/sbin/lighttpd -f /etc/light 727 1 root S 1480 4% 0% /usr/sbin/dropbear 716 1 root S 1432 4% 0% /bin/vftpd -r 854 712 root S 1352 3% 0% -sh 647 1 root S 1352 3% 0% /bin/sh 654 1 root S 1312 3% 0% /usr/sbin/syslogd -m 0 -o 40000 657 1 root S 1144 3% 0% /usr/sbin/klogd -x 1 0 root S 1136 3% 0% init 712 1 root S 1136 3% 0% /bin/utelnetd -d 651 1 root S 1136 3% 0% /sbin/respawnd 746 1 root S 1136 3% 0% /usr/local/sbin/imgsrv -p 8081 752 1 root S 1120 3% 0% /usr/local/sbin/launch_php_script 2 /u #### i setup camera to 1280x720 @ 24.989 fps 51K run mplayer MPlayer SVN-r33713-4.6.1 (C) 2000-2011 MPlayer Team mplayer: could not connect to socket mplayer: No such file or directory Failed to open LIRC support. You will not be able to use your remote control. Playing rtsp://192.168.0.9:554. Resolving 192.168.0.9 for AF_INET6... Couldn't resolve name for AF_INET6: 192.168.0.9 Connecting to server 192.168.0.9[192.168.0.9]: 554... rtsp_session: unsupported RTSP server. Server type is 'unknown'. Resolving 192.168.0.9 for AF_INET6... Couldn't resolve name for AF_INET6: 192.168.0.9 Connecting to server 192.168.0.9[192.168.0.9]: 554... http_read_response read 0 (i.e. EOF). No stream found to handle url rtsp://192.168.0.9:554 Exiting... (End of file) i cant get the stream with the same computer, i setup camera to 640x480 @ 24.989 fps 18K and launch mplayer from other laptop ubuntu in the same lan (the camera is conected to a router, and also the pcs) -------------------------- top while running (non stop) Mem: 27264K used, 13112K free, 0K shrd, 0K buff, 16248K cached CPU: 0% usr 3% sys 0% nic 94% idle 0% io 0% irq 1% sirq Load average: 0.02 0.08 0.08 2/34 1129 PID PPID USER STAT VSZ %MEM %CPU COMMAND 830 829 root S 44928 111% 4% /usr/local/bin/str 860 854 root R 1496 4% 0% top 751 1 root R 4136 10% 0% /usr/local/sbin/autoexposure 827 1 root S 44928 111% 0% /usr/local/bin/str 829 827 root S 44928 111% 0% /usr/local/bin/str 765 763 root S 30936 76% 0% /usr/local/sbin/php 764 763 root S 30936 76% 0% /usr/local/sbin/php 763 759 root S 30872 76% 0% /usr/local/sbin/php 759 1 root S 5288 13% 0% /usr/local/sbin/lighttpd -f /etc/light 727 1 root S 1480 4% 0% /usr/sbin/dropbear 716 1 root S 1432 4% 0% /bin/vftpd -r 854 712 root S 1352 3% 0% -sh 647 1 root S 1352 3% 0% /bin/sh 654 1 root S 1312 3% 0% /usr/sbin/syslogd -m 0 -o 40000 657 1 root S 1144 3% 0% /usr/sbin/klogd -x 1 0 root S 1136 3% 0% init 746 1 root S 1136 3% 0% /usr/local/sbin/imgsrv -p 8081 712 1 root S 1136 3% 0% /bin/utelnetd -d 651 1 root S 1136 3% 0% /sbin/respawnd 752 1 root S 1120 3% 0% /usr/local/sbin/launch_php_script 2 /u i setup again to 1280x720 @ 24.989 fps 51K and launch mplayer from the other laptop top while running mplayer (about 10 seconds) Mem: 27376K used, 13000K free, 0K shrd, 0K buff, 16248K cached CPU: 0% usr 4% sys 0% nic 92% idle 0% io 0% irq 1% sirq Load average: 0.29 0.14 0.10 2/34 1189 PID PPID USER STAT VSZ %MEM %CPU COMMAND 860 854 root R 1496 4% 0% top 854 712 root S 1352 3% 0% -sh 830 829 root S 44928 111% 6% /usr/local/bin/str and now top before mplayer crashes Mem: 27296K used, 13080K free, 0K shrd, 0K buff, 16248K cached CPU: 0% usr 0% sys 0% nic 98% idle 0% io 0% irq 1% sirq Load average: 0.41 0.19 0.12 2/34 1189 PID PPID USER STAT VSZ %MEM %CPU COMMAND 860 854 root R 1496 4% 0% top 854 712 root S 1352 3% 0% -sh 830 829 root S 44928 111% 0% /usr/local/bin/str 829 827 root S 44928 111% 0% /usr/local/bin/str 827 1 root S 44928 111% 0% /usr/local/bin/str 765 763 root S 30936 76% 0% /usr/local/sbin/php 764 763 root S 30936 76% 0% /usr/local/sbin/php 763 759 root S 30872 76% 0% /usr/local/sbin/php 759 1 root S 5296 13% 0% /usr/local/sbin/lighttpd -f /etc/light 752 1 root S 1120 3% 0% /usr/local/sbin/launch_php_script 2 /u 751 1 root S 4136 10% 0% /usr/local/sbin/autoexposure 750 1 root R 1120 3% 0% /usr/local/sbin/autocampars 746 1 root S 1136 3% 0% /usr/local/sbin/imgsrv -p 8081 727 1 root S 1480 4% 0% /usr/sbin/dropbear 716 1 root S 1432 4% 0% /bin/vftpd -r 712 1 root S 1136 3% 0% /bin/utelnetd -d 657 1 root S 1144 3% 0% /usr/sbin/klogd -x 654 1 root S 1312 3% 0% /usr/sbin/syslogd -m 0 -o 40000 651 1 root S 1136 3% 0% /sbin/respawnd 647 1 root S 1352 3% 0% /bin/sh then the camera dont respond and hangs, last top showed is: Mem: 27344K used, 13032K free, 0K shrd, 0K buff, 16248K cached CPU: 0% usr 4% sys 0% nic 91% idle 0% io 0% irq 2% sirq Load average: 0.03 0.11 0.09 2/34 1190 PID PPID USER STAT VSZ %MEM %CPU COMMAND 830 829 root S 44928 111% 7% /usr/local/bin/str 1190 854 root R 1496 4% 0% top 827 1 root S 44928 111% 0% /usr/local/bin/str 2012/5/18 Oleg <[email protected]>: >> 2. Command "top" right after the boot + before/after you launch >> mplayer could be helpful. > > I meant before the mplayer crashes. > > On 18 May 2012 12:52, Oleg <[email protected]> wrote: >> >> Carlos, >> >> "Top"s look ok. I also tried a camera with the 8.1.2 firmware and my PC - >> streaming works at 1920x1088. >> >> Sorry, I forgot to ask you to check a few more things: >> >> 1. You should have a usb-serial cable - could you connect it and send us >> the camera boot log? And also the info the camera writes when the streamer >> is working. >> 2. Command "top" right after the boot + before/after you launch >> mplayer could be helpful. >> >> Best regards, >> Oleg Dzhimiev >> Electronics Engineer >> phone: +1 801 783 5555 x124 >> Elphel, Inc. >> >> >> On 18 May 2012 06:53, Carlos Padial <[email protected]> wrote: >>> >>> > PC's OS - ? >>> >>> ok, lets me explain... >>> >>> i have two computers. A netbook (samsung n150, atom) with linux mint >>> 12 32 bits, ubuntu 10.10 32 bits, and with this computer i also use >>> the live usb. >>> >>> The second one is an intel i7 with linux mint 12 64bits, ubuntu 12.04 >>> 32bits, (and till yesterday ubuntu 11.10) >>> When i try the live usb with this computer it works badly... >>> (resolution is 640x400 and window management gests crazy everytime... >>> making it unusable... >>> >>> When i have tried to install the usb, it doenst seems to recognice the >>> password i entered during the instalation so i'm only working with the >>> live version. >>> >>> I have tried mplayer with all of this OS and the results are similar. >>> >>> With the liveusb in the atom netbook i believe the problem is that the >>> netbook seems not to be able to open high resolution streams, with >>> 1920x1088 (128K) dont show any image, but i tried 640x480 (24k) and >>> the image is showed and even mantained for a long time (30-50 seconds) >>> But after that mplayer exits >>> >>> The best results i had was in the i7 with ubuntu 12, mplayer (MPlayer >>> svn r34540 (Ubuntu) and 640x480 (24k) , the live preview was working >>> without stop (i stopped it) >>> >>> when i setup 1280x720 (73k) and mplayer dont show the image... >>> i come back to 640x480 (27k) and the live preview works fine... this >>> is the only setup showing the live preview non stop... >>> >>> with 800x600 (40k) the preview show the image for 2 seconds and then >>> stops.. >>> above this resolution the image is not showed (only one time each 10... >>> >>> > Camera firmware - ? >>> >>> Firmware Version: Elphel (R) Model 353 Camera release 8.1.2 >>> >>> > FPS = 24? >>> >>> now i'm limitting fps to 25 (using instructions from wiki FPScontrol) >>> >>> > Image dimensions and size - 1920x1088, 100-150KB? >>> >>> > Mplayer version (let's stick to mplayer)? >>> >>> MPlayer svn r34540 (Ubuntu) (in ubuntu 12, where i have the best >>> results for the moment) >>> >>> > During that 5-10 sec of working the window with image opens, right? or >>> > it >>> >>> > just crashes not showing anything? >>> >>> when i say mplayer is working i mean it opens a window and the image >>> is showed. Then the window close and mplayer says: >>> >>> Exiting... (End of file) >>> >>> > 2. Some things that you could try: >>> > Does mplayer act the same if you boot from our LiveUSB? >>> >>> Yes, the response is similar but i need to run liveUSB correctly in >>> the i7 to test... >>> >>> > Check the CPU usage on the camera - "top" or "ps" from the telnet >>> > session - >>> > could also you send us this info? >>> >>> >>> top------------------------------------------------------------------------------------------- >>> >>> Mem: 27384K used, 12992K free, 0K shrd, 0K buff, 16248K cached >>> CPU: 0% usr 0% sys 0% nic 98% idle 0% io 0% irq 0% sirq >>> Load average: 0.27 0.26 0.26 5/34 2001 >>> PID PPID USER STAT VSZ %MEM %CPU COMMAND >>> 751 1 root S 4136 10% 1% /usr/local/sbin/autoexposure >>> 2001 1996 root R 1496 4% 0% top >>> 830 829 root S 44928 111% 0% /usr/local/bin/str >>> 827 1 root S 44928 111% 0% /usr/local/bin/str >>> 829 827 root S 44928 111% 0% /usr/local/bin/str >>> 765 763 root S 30936 76% 0% /usr/local/sbin/php >>> 764 763 root S 30936 76% 0% /usr/local/sbin/php >>> 763 759 root S 30872 76% 0% /usr/local/sbin/php >>> 759 1 root S 5336 13% 0% /usr/local/sbin/lighttpd -f >>> /etc/light >>> 727 1 root S 1480 4% 0% /usr/sbin/dropbear >>> 716 1 root S 1432 4% 0% /bin/vftpd -r >>> 1996 712 root S 1352 3% 0% -sh >>> 647 1 root S 1352 3% 0% /bin/sh >>> 654 1 root S 1312 3% 0% /usr/sbin/syslogd -m 0 -o 40000 >>> 657 1 root S 1144 3% 0% /usr/sbin/klogd -x >>> 1 0 root S 1136 3% 0% init >>> 746 1 root S 1136 3% 0% /usr/local/sbin/imgsrv -p 8081 >>> 651 1 root S 1136 3% 0% /sbin/respawnd >>> 712 1 root S 1136 3% 0% /bin/utelnetd -d >>> 752 1 root S 1120 3% 0% >>> /usr/local/sbin/launch_php_script 2 /u >>> >>> this is top with the camera configured with 1280x720 (73k) >>> then i start mplayer in other terminal and the streamed video is >>> showed for 2 seconds... when the mplayer stop, top show this other >>> info: >>> >>> Mem: 27456K used, 12920K free, 0K shrd, 0K buff, 16248K cached >>> CPU: 0% usr 1% sys 0% nic 97% idle 0% io 0% irq 1% sirq >>> Load average: 0.20 0.24 0.25 2/34 2001 >>> PID PPID USER STAT VSZ %MEM %CPU COMMAND >>> 2001 1996 root R 1496 4% 1% top >>> 751 1 root S 4136 10% 0% /usr/local/sbin/autoexposure >>> 830 829 root S 44928 111% 0% /usr/local/bin/str >>> 750 1 root R 1120 3% 0% /usr/local/sbin/autocampars >>> 827 1 root S 44928 111% 0% /usr/local/bin/str >>> 829 827 root S 44928 111% 0% /usr/local/bin/str >>> 765 763 root S 30936 76% 0% /usr/local/sbin/php >>> 764 763 root S 30936 76% 0% /usr/local/sbin/php >>> 763 759 root S 30872 76% 0% /usr/local/sbin/php >>> 759 1 root S 5336 13% 0% /usr/local/sbin/lighttpd -f >>> /etc/light >>> 727 1 root S 1480 4% 0% /usr/sbin/dropbear >>> 716 1 root S 1432 4% 0% /bin/vftpd -r >>> 1996 712 root S 1352 3% 0% -sh >>> 647 1 root S 1352 3% 0% /bin/sh >>> 654 1 root S 1312 3% 0% /usr/sbin/syslogd -m 0 -o 40000 >>> >>> ps------------------------------------------- >>> >>> PID USER VSZ STAT COMMAND >>> >>> 1 root 1136 S init >>> 2 root 0 SWN [ksoftirqd/0] >>> 3 root 0 SW [watchdog/0] >>> 4 root 0 SW< [events/0] >>> 5 root 0 SW< [khelper] >>> 6 root 0 SW< [kthread] >>> 8 root 0 SW< [kblockd/0] >>> 11 root 0 SW< [khubd] >>> 23 root 0 SW [pdflush] >>> 24 root 0 SW [pdflush] >>> 25 root 0 SW< [kswapd0] >>> 26 root 0 SW< [aio/0] >>> 568 root 0 SW [mtdblockd] >>> 602 root 0 SWN [jffs2_gcd_mtd4] >>> 647 root 1352 S /bin/sh >>> 651 root 1136 S /sbin/respawnd >>> 654 root 1312 S /usr/sbin/syslogd -m 0 -o 40000 >>> 657 root 1144 S /usr/sbin/klogd -x >>> 712 root 1136 S /bin/utelnetd -d >>> 716 root 1432 S /bin/vftpd -r >>> 727 root 1480 S /usr/sbin/dropbear >>> 746 root 1136 S /usr/local/sbin/imgsrv -p 8081 >>> 750 root 1120 S /usr/local/sbin/autocampars >>> 751 root 4136 S /usr/local/sbin/autoexposure >>> 752 root 1120 S /usr/local/sbin/launch_php_script 2 >>> /usr/local/sbin/c >>> 759 root 5336 S /usr/local/sbin/lighttpd -f /etc/lighttpd.conf >>> -m /us >>> 763 root 30872 S /usr/local/sbin/php >>> 764 root 30936 S /usr/local/sbin/php >>> 765 root 30936 S /usr/local/sbin/php >>> 827 root 44928 S /usr/local/bin/str >>> 829 root 44928 S /usr/local/bin/str >>> 830 root 44928 S /usr/local/bin/str >>> 1996 root 1352 S -sh >>> 2002 root 1488 R ps >>> >>> usually when i use telnet after mplayer exits, telnet didnt respond for a >>> while. >>> >>> it seems that with gstreamer when this happends, i need to restart the >>> camera, but with mplayer i dont need to restart the camera (yet) >>> >>> > Your PC/laptop CPU usage? >>> >>> top running in my i7 (ubuntu 12.04) shows: >>> >>> top - 13:55:00 up 1:49, 4 users, load average: 0.92, 0.97, 1.04 >>> Tasks: 198 total, 2 running, 196 sleeping, 0 stopped, 0 zombie >>> Cpu(s): 1.8%us, 0.5%sy, 0.0%ni, 97.7%id, 0.0%wa, 0.0%hi, 0.0%si, >>> 0.0%st >>> Mem: 12401224k total, 2853840k used, 9547384k free, 142224k buffers >>> Swap: 524284k total, 0k used, 524284k free, 1919880k cached >>> >>> PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND >>> 2662 root 20 0 70732 51m 12m S 6 0.4 7:02.82 Xorg >>> 3346 carlos 20 0 467m 161m 23m S 3 1.3 5:35.28 >>> plugin-containe >>> 2913 carlos 20 0 328m 164m 38m S 2 1.4 13:12.51 compiz >>> 1659 carlos 9 -11 171m 5696 4104 S 1 0.0 1:23.66 >>> pulseaudio >>> 3884 carlos 20 0 96084 17m 11m S 1 0.1 0:29.12 >>> gnome-terminal >>> 3309 carlos 20 0 547m 179m 32m S 0 1.5 4:15.87 firefox >>> 5669 root 20 0 0 0 0 S 0 0.0 0:00.91 >>> kworker/0:1 >>> 5825 carlos 20 0 2836 1200 884 R 0 0.0 0:00.03 top >>> 1 root 20 0 3636 1984 1284 S 0 0.0 0:01.26 init >>> 2 root 20 0 0 0 0 S 0 0.0 0:00.00 kthreadd >>> 3 root 20 0 0 0 0 S 0 0.0 0:00.12 >>> ksoftirqd/0 >>> 6 root RT 0 0 0 0 S 0 0.0 0:00.00 >>> migration/0 >>> 7 root RT 0 0 0 0 S 0 0.0 2:09.07 >>> watchdog/0 >>> 8 root RT 0 0 0 0 S 0 0.0 0:00.00 >>> migration/1 >>> 10 root 20 0 0 0 0 S 0 0.0 0:00.05 >>> ksoftirqd/1 >>> 12 root RT 0 0 0 0 S 0 0.0 0:29.46 >>> watchdog/1 >>> 13 root RT 0 0 0 0 S 0 0.0 0:00.00 >>> migration/2 >>> 15 root 20 0 0 0 0 S 0 0.0 0:00.05 >>> ksoftirqd/2 >>> 16 root RT 0 0 0 0 S 0 0.0 0:00.01 >>> watchdog/2 >>> 17 root RT 0 0 0 0 S 0 0.0 0:00.00 >>> migration/3 >>> 19 root 20 0 0 0 0 S 0 0.0 0:00.03 >>> ksoftirqd/3 >>> 20 root RT 0 0 0 0 S 0 0.0 0:00.04 >>> watchdog/3 >>> 21 root RT 0 0 0 0 S 0 0.0 0:00.00 >>> migration/4 >>> 23 root 20 0 0 0 0 S 0 0.0 0:00.01 >>> ksoftirqd/4 >>> 24 root RT 0 0 0 0 S 0 0.0 0:00.01 >>> watchdog/4 >>> 25 root RT 0 0 0 0 S 0 0.0 0:00.00 >>> migration/5 >>> 27 root 20 0 0 0 0 S 0 0.0 0:00.00 >>> ksoftirqd/5 >>> 28 root RT 0 0 0 0 S 0 0.0 0:00.01 >>> watchdog/5 >>> 29 root RT 0 0 0 0 S 0 0.0 0:00.00 >>> migration/6 >>> 30 root 20 0 0 0 0 S 0 0.0 0:00.00 >>> kworker/6:0 >>> 31 root 20 0 0 0 0 S 0 0.0 0:00.00 >>> ksoftirqd/6 >>> 32 root RT 0 0 0 0 S 0 0.0 0:00.01 >>> watchdog/6 >>> 33 root RT 0 0 0 0 S 0 0.0 0:00.00 >>> migration/7 >>> 35 root 20 0 0 0 0 S 0 0.0 0:00.01 >>> ksoftirqd/7 >>> 36 root RT 0 0 0 0 S 0 0.0 0:00.01 watchdog/7 >>> >>> > Best regards, >>> > Oleg Dzhimiev >>> > Electronics Engineer >>> > phone: +1 801 783 5555 x124 >>> > Elphel, Inc. >>> >>> >>> >>> -- >>> Carlos Padial >>> surreal.asturnazari.es >>> >>> _______________________________________________ >>> Support-list mailing list >>> [email protected] >>> >>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com >> >> >> > > > > -- > Best regards, > Oleg Dzhimiev > Electronics Engineer > phone: +1 801 783 5555 x124 > Elphel, Inc. -- Carlos Padial surreal.asturnazari.es _______________________________________________ Support-list mailing list [email protected] http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
