One more thing though. In the cases when you cannot telnet to the camera - I got that the serial output doesn't display to much. Can you send commands through the serial cable? "ifconfig", for example.
Best regards, Oleg Dzhimiev Electronics Engineer phone: +1 801 783 5555 x124 Elphel, Inc. On 24 May 2012 09:57, Oleg <[email protected]> wrote: > Carlos, > > So, I think the best solution here would be to send the camera to us. > You could try updating the software but most likely it won't work. > > Sorry for the troubles. > > Best regards, > Oleg Dzhimiev > Electronics Engineer > phone: +1 801 783 5555 x124 > Elphel, Inc. > > On 21 May 2012 18:41, Carlos Padial <[email protected]> wrote: >> the pc is connected over a cable to the router, and also the camera. >> >> in the ttylog i get no outputs when the stream stops... >> >> in the telnet session one time i get this message, but no longer repeats... >> >> Elphel353 login: root >> Password: >> [root@Elphel353 /root]1068# killall -9 str >> [root@Elphel353 /root]1068# /usr/local/bin/str >> STATE_DISCONNECT; fd == 10; revents == 25 >> >> After that using this command flavio suggest: >> mplayer rtsp://192.168.0.9:554 -vo x11 -vf scale=480:320 >> >> for a while it remains with crashes (with no report) >> and after that i managed to stream 1920x1088 24.995fps 136K >> for several minutes the live preview works fine... then crashes and >> need to restart. >> >> just when mplayer crashes, top is updated and all process disapear >> except a few ones... >> >> Mem: 26048K used, 14328K free, 0K shrd, 0K buff, 14984K cached >> CPU: 0% usr 4% sys 0% nic 92% idle 0% io 0% irq 1% sirq >> Load average: 0.08 0.18 0.12 3/34 1151 >> PID PPID USER STAT VSZ %MEM %CPU COMMAND >> 831 830 root R 44928 111% 5% /usr/local/bin/str >> >> again, after stream live preview for two seconds at 800x608 50K >> >> Mem: 26216K used, 14160K free, 0K shrd, 0K buff, 15016K cached >> CPU: 57% usr 7% sys 0% nic 31% idle 0% io 0% irq 3% sirq >> Load average: 0.61 0.40 0.20 7/35 1281 >> PID PPID USER STAT VSZ %MEM %CPU COMMAND >> 770 764 root S 30936 76% 21% /usr/local/sbin/php >> 771 764 root S 30936 76% 19% /usr/local/sbin/php >> 836 1 root S 44928 111% 1% /usr/local/bin/str >> >> again >> >> Mem: 26064K used, 14312K free, 0K shrd, 0K buff, 15016K cached >> CPU: 0% usr 4% sys 0% nic 92% idle 0% io 0% irq 1% sirq >> Load average: 0.24 0.35 0.19 6/34 1281 >> PID PPID USER STAT VSZ %MEM %CPU COMMAND >> 839 838 root S 44928 111% 6% /usr/local/bin/str >> 769 756 root R 1496 4% 0% top >> 836 1 root S 44928 111% 0% /usr/local/bin/str >> >> again >> >> Mem: 26056K used, 14320K free, 0K shrd, 0K buff, 15016K cached >> CPU: 0% usr 4% sys 0% nic 93% idle 0% io 0% irq 1% sirq >> Load average: 0.01 0.19 0.16 2/34 1283 >> PID PPID USER STAT VSZ %MEM %CPU COMMAND >> 839 838 root S 44928 111% 4% /usr/local/bin/str >> 712 1 root S 1136 3% 0% /bin/utelnetd -d >> 751 1 root S 4136 10% 0% /usr/local/sbin/autoexposure >> >> sometimes after that i need to wait some minutes, and the camera >> responds again, but after that i need to reboot... >> >> sometimes i can acces telnet when the camera crashes, i kill str and >> run it again, but almost everytime it is not possible as telnet gets >> freezed. >> >> 640x480 works always and full window works for 30-60 seconds... >> >> When connected directly to the pc (without router), stream least a >> little more time, but no other changes... >> >> ??? >> >> >> 2012/5/19 Oleg <[email protected]>: >>> Well. I see, thanks for the logs. >>> >>> 1. Are your PCs connected over WiFi or cable? Try to connect one of the PCs >>> over a cable - so the LAN from the camera to a PC would be wired only. >>> 2. If you kill the streamer process and start it manually it will be >>> displaying errors at the output. So it should report an error when mplayer >>> crashes. >>>> >>>> killall -9 str >>>> >>>> /usr/local/bin/str >>> >>> >>> Oleg >> >> >> >> -- >> Carlos Padial >> surreal.asturnazari.es >> >> _______________________________________________ >> Support-list mailing list >> [email protected] >> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com _______________________________________________ Support-list mailing list [email protected] http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
