Are you sure that it isnt a Thunderbolt E which is somewhat different
from the earlier models:
http://trl.trimble.com/docushare/dsweb/Get/Document-383329/022542-010B_Thunderbolt-E_DS_0807.pdf
Can you post some images?
Bruce
Stanley Reynolds wrote:
Have you seen this:
http://www.leapsecond.com/pages/tapr-tbolt/
and
http://www.prc68.com/I/ThunderBolt.shtml
Stanley
----- Original Message ----
From: SAL CORNACCHIA<[email protected]>
To: Discussion of precise time and frequency measurement<[email protected]>
Sent: Fri, January 15, 2010 3:51:20 PM
Subject: [time-nuts] need help on Tbolt
Can someone help with the software for a Tbolt 35757256 built 6/2/05 A002206,61
Rev E, I just received this unit from China without any information or manual
or software, I am about to built the power supply for it and would appreciate
any help possible
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
________________________________
From: David C. Partridge<[email protected]>
To: Discussion of precise time and frequency measurement<[email protected]>
Sent: Thu, January 14, 2010 1:14:36 PM
Subject: Re: [time-nuts] T-Bolt Question
Or use the beta realase of Lady Heather to do a 48 hour accurate survey.
Dave
-----Original Message-----
From: [email protected] [mailto:[email protected]] On
Behalf Of Ken Winterling
Sent: 14 January 2010 17:53
To: Discussion of precise time and frequency measurement
Subject: Re: [time-nuts] T-Bolt Question
To All,
The following procedure is taken from notes I made years ago when setting up
my TBOLT using TBOLTMON. I have never had to enter the information again and
the unit recovers automatically even after extended power failures that
exhausted its UPS.
Click Setup -> Self-Survey,
Click the "Enable" and "Save" buttons
Click "Set Survey",
Click "Save Segment",
Click "Close"
Click Control -> Restart Self-Survey.
The "Saved Position" alarm should change to green once the survey process
finishes.
You do not need to copy anything manually unless you want to specify a
more-accurate survey position than what the Thunderbolt arrives at on its
own.
Ken, WA2LBI
On Thu, Jan 14, 2010 at 12:07, Jim Mandaville<[email protected]> wrote:
Starting without good saved coordinates will put you into search mode,
and it may take around 45 minutes to an hour to establish a position,
after which you will see SVs and AMUs.
Once you get a good position, either from self-survey by the Tbolt or
by a different GPS, you can enter these as follows:
On the Tbolt monitor main page:
go to menu heading setting "setup"; under that, go to "position"
In the "position" window, type in your coordinates. (The lat. and long.
must be in degrees and decimal degrees. If you are starting with
degrees, minutes and decimal minutes, divide the minutes with decimal
minutes by 60 and add the result to your original whole degrees.) The
longitude must start with a negative sign if it is west. For east, no
sign is required.
click "set accurate position"; then click "save segment" and close the
window
you should now see the saved position in the main Tbolt window and the
Tbolt will now start from scratch using these coordinates. This will
reduce your fix time to a few minutes.
Jim
HI Dick,
I have the same problem and nothing works to enter the coordonates.
More, i don't see the SV nor AMUs.
73
Alain
F4GBC
----- Original Message ----- From: "Richard W. Solomon"<
[email protected]>
To:<[email protected]>
Sent: Thursday, January 14, 2010 3:50 AM
Subject: Re: [time-nuts] T-Bolt Question
Perhaps I posted this to the wrong forum ??
Maybe if I had Duct-Taped it to a pendulum I may have gotten more
responses ??
73, Dick, W1KSZ
-----Original Message-----
From: "Richard W.. Solomon"<[email protected]>
Sent: Jan 12, 2010 5:20 PM
To: [email protected]
Subject: [time-nuts] E-Bolt Question
I am in T-Bolt Monitor software. The "Saved Position" is Yellow.
How do I get the T-Bolt to save the survey results ?
Thanks, Dick, W1KSZ
_______________________________________________
_______________________________________________
time-nuts mailing list -- [email protected] To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
_______________________________________________
time-nuts mailing list -- [email protected]
To unsubscribe, go to https://www..febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
_______________________________________________
time-nuts mailing list -- [email protected]
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
_______________________________________________
time-nuts mailing list -- [email protected]
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
_______________________________________________
time-nuts mailing list -- [email protected]
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
