No the picture is not the same. Sal
________________________________ From: Bruce Griffiths <[email protected]> To: Discussion of precise time and frequency measurement <[email protected]> Sent: Fri, January 15, 2010 6:07:31 PM Subject: Re: [time-nuts] need help on Tbolt Are you sure that it isnt a Thunderbolt E which is somewhat different from the earlier models: http://trl.trimble.com/docushare/dsweb/Get/Document-383329/022542-010B_Thunderbolt-E_DS_0807..pdf Can you post some images? Bruce Stanley Reynolds wrote: > Have you seen this: > > http://www.leapsecond.com/pages/tapr-tbolt/ > > and > > http://www.prc68.com/I/ThunderBolt.shtml > > Stanley > > > > ----- Original Message ---- > From: SAL CORNACCHIA<[email protected]> > To: Discussion of precise time and frequency measurement<[email protected]> > Sent: Fri, January 15, 2010 3:51:20 PM > Subject: [time-nuts] need help on Tbolt > > > Can someone help with the software for a Tbolt 35757256 built 6/2/05 > A002206,61 Rev E, I just received this unit from China without any > information or manual or software, I am about to built the power supply for > it and would appreciate any help possible > Best regards, > > Sal C. Cornacchia > Electronic RF Microwave Engineer (Ret.) > > > > > > > > ________________________________ > From: David C. Partridge<[email protected]> > To: Discussion of precise time and frequency measurement<[email protected]> > Sent: Thu, January 14, 2010 1:14:36 PM > Subject: Re: [time-nuts] T-Bolt Question > > Or use the beta realase of Lady Heather to do a 48 hour accurate survey. > > Dave > > -----Original Message----- > From: [email protected] [mailto:[email protected]] On > Behalf Of Ken Winterling > Sent: 14 January 2010 17:53 > To: Discussion of precise time and frequency measurement > Subject: Re: [time-nuts] T-Bolt Question > > To All, > > The following procedure is taken from notes I made years ago when setting up > my TBOLT using TBOLTMON. I have never had to enter the information again and > the unit recovers automatically even after extended power failures that > exhausted its UPS. > > Click Setup -> Self-Survey, > Click the "Enable" and "Save" buttons > Click "Set Survey", > Click "Save Segment", > Click "Close" > Click Control -> Restart Self-Survey. > > The "Saved Position" alarm should change to green once the survey process > finishes. > > You do not need to copy anything manually unless you want to specify a > more-accurate survey position than what the Thunderbolt arrives at on its > own. > > Ken, WA2LBI > > > On Thu, Jan 14, 2010 at 12:07, Jim Mandaville<[email protected]> wrote: > > >> Starting without good saved coordinates will put you into search mode, >> and it may take around 45 minutes to an hour to establish a position, >> after which you will see SVs and AMUs. >> >> Once you get a good position, either from self-survey by the Tbolt or >> by a different GPS, you can enter these as follows: >> >> On the Tbolt monitor main page: >> >> go to menu heading setting "setup"; under that, go to "position" >> >> In the "position" window, type in your coordinates. (The lat. and long. >> must be in degrees and decimal degrees. If you are starting with >> degrees, minutes and decimal minutes, divide the minutes with decimal >> minutes by 60 and add the result to your original whole degrees.) The >> longitude must start with a negative sign if it is west. For east, no >> > sign is required. > >> click "set accurate position"; then click "save segment" and close the >> window >> >> you should now see the saved position in the main Tbolt window and the >> Tbolt will now start from scratch using these coordinates. This will >> reduce your fix time to a few minutes. >> >> Jim >> >> >> >> >> >> >> >> >> HI Dick, >> >>> I have the same problem and nothing works to enter the coordonates. >>> More, i don't see the SV nor AMUs. >>> 73 >>> Alain >>> F4GBC >>> >>> ----- Original Message ----- From: "Richard W. Solomon"< >>> [email protected]> >>> >>> To:<[email protected]> >>> Sent: Thursday, January 14, 2010 3:50 AM >>> >>> Subject: Re: [time-nuts] T-Bolt Question >>> >>> >>> >>>> Perhaps I posted this to the wrong forum ?? >>>> Maybe if I had Duct-Taped it to a pendulum I may have gotten more >>>> responses ?? >>>> >>>> 73, Dick, W1KSZ >>>> >>>> >>>> -----Original Message----- >>>> >>>> >>>>> From: "Richard W.. Solomon"<[email protected]> >>>>> Sent: Jan 12, 2010 5:20 PM >>>>> To: [email protected] >>>>> Subject: [time-nuts] E-Bolt Question >>>>> >>>>> I am in T-Bolt Monitor software. The "Saved Position" is Yellow. >>>>> How do I get the T-Bolt to save the survey results ? >>>>> >>>>> Thanks, Dick, W1KSZ >>>>> >>>>> _______________________________________________ >>>>> >>>>> >>>> >> >> > _______________________________________________ > time-nuts mailing list -- [email protected] To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > > > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to https://www..febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > > > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > > _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
