Diddier Thank you. For everyone else I just completed and emailed a word doc to Bob who offered to host it. Its 7 MB. Turned out very nicely. You also have my hints on the project. Diddier I will upload it shortly to your site also. The lamps re-installed and the HP5065a is warming up. I do have photo current now and oven teps are looking correct or at least getting there. Thanks everyone. Paul WB8TSL
On Tue, Sep 27, 2011 at 6:01 PM, <[email protected]> wrote: > That will be fine :) > > Didier KO4BB > > Sent from my BlackBerry Wireless thingy while I do other things... > > -----Original Message----- > From: paul swed <[email protected]> > Sender: [email protected] > Date: Tue, 27 Sep 2011 09:04:32 > To: Discussion of precise time and frequency measurement< > [email protected]> > Reply-To: Discussion of precise time and frequency measurement > <[email protected]> > Subject: Re: [time-nuts] HP 5065a failure of Rb oscillator problem solved > > Happy to post the pix someplace but do not have any accounts like facebook > etc. > Though a great home would be Diddiers site. I could send perhaps 10 of the > best pix. > By the way looking into the oven you can see the glass rb filter cell. Talk > about a classy piece of technology. This ain't no FRS-c. ;-) > > On Mon, Sep 26, 2011 at 10:38 PM, WB6BNQ <[email protected]> wrote: > > > Paul, > > > > As would I. > > > > Bill....WB6BNQ > > > > "J. L. Trantham" wrote: > > > > > Paul, > > > > > > I would love to see the pictures. > > > > > > Joe > > > > > > -----Original Message----- > > > From: [email protected] [mailto:[email protected]] > On > > > Behalf Of paul swed > > > Sent: Monday, September 26, 2011 9:16 PM > > > To: Time-nuts; paul swed > > > Subject: [time-nuts] HP 5065a failure of Rb oscillator problem solved > > > > > > Hello to the group my trusty HP 5065a Rb ref died. Digging in I > > discovered > > > that the Rb oscillator was not drawing any current. So it was time to > go > > > deep inside and see whats in there. Have taken pix of the innards but > > they > > > are each 2 MB in size. Anyhow it was A12R1 a 1330 ohm resistor that > seems > > to > > > be open. Jumpered a 1500 ohm R in and the lamp re-ignites. Now to > install > > > appropriate quality and temperature replacement and I should be back in > > > business. Must say the 3 levels of magnetic shielding really is > > impressive. > > > Regards Paul WB8TSL _______________________________________________ > > > time-nuts mailing list -- [email protected] > > > To unsubscribe, go to > > > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > > > and follow the instructions there. > > > > > > _______________________________________________ > > > time-nuts mailing list -- [email protected] > > > To unsubscribe, go to > > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > > > and follow the instructions there. > > > > > > _______________________________________________ > > time-nuts mailing list -- [email protected] > > To unsubscribe, go to > > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > > and follow the instructions there. > > > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
