Hi Eric; That seemed logical, but I could imagine some topography where looping the signal may have made sense. Thanks Again; Thomas Knox
> Date: Mon, 12 Nov 2012 10:13:53 -0800 > From: [email protected] > To: [email protected] > Subject: Re: [time-nuts] SR620 software and adjustment Ref queston > > the ""reference" in step 2 is the best reference you own, not the > internal ref. sorry for the confusion. > > -eric > > On Mon, Nov 12, 2012 at 9:59 AM, Tom Knox <[email protected]> wrote: > > > > In step 2 is this my Lab Ref, or the SR620 ref out that is put into Ext > > Ref and Input A ? > > > > Thomas Knox > > > > > > > >> Date: Mon, 12 Nov 2012 09:52:13 -0800 > >> From: [email protected] > >> To: [email protected] > >> Subject: Re: [time-nuts] SR620 software and adjustment > >> > >> Volker: > >> > >> This is the adjustment procedure that I used: > >> > >> Use the following adjustment sequence to get the frequency spot on: > >> > >> 1. Set the Cal jumper to Cal Enable > >> 2. Connect the reference to Ext Ref (rear) and Input A > >> 3. Switch the counter to Ext Ref > >> 4. Set the CalByte 50 for the best display (this is a very fine > >> adjustement) > >> 5. Switch the counter to Int Ref > >> 6. Set the CalByte 4 for the best display (this adjustement is coarse, > >> optimize!) > >> 7. Set the Cal jumper to Cal Disable > >> > >> > >> The procedure can be found in the list archives and at Brooke Clarke's > >> website at: http://www.prc68.com/I/TandFTE.shtml > >> > >> -Eric > >> > >> > >> > >> On Mon, Nov 12, 2012 at 8:05 AM, Volker Esper <[email protected]> wrote: > >> > > >> > Sorry, I don't want to annoy you, but I can't find the > >> > alignment/adjustment > >> > procedure for the SR620 - once, I had it... :-( I don's mean that in the > >> > manual, there must be another one Bob talked about. > >> > > >> > By the way: is there any suitable vindous software out there, for talking > >> > (and listening) to the SR620 via RS-232? A program like Ulrichs Z38xx > >> > would > >> > be nice... > >> > > >> > Thanks a lot and please don't be annoyed - I guess this kind of question > >> > is > >> > not very inspiring. > >> > > >> > Volker > >> > > >> > > >> > _______________________________________________ > >> > time-nuts mailing list -- [email protected] > >> > To unsubscribe, go to > >> > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > >> > and follow the instructions there. > >> > >> > >> > >> -- > >> --Eric > >> _________________________________________ > >> Eric Garner > >> > >> _______________________________________________ > >> time-nuts mailing list -- [email protected] > >> To unsubscribe, go to > >> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > >> and follow the instructions there. > > > > _______________________________________________ > > time-nuts mailing list -- [email protected] > > To unsubscribe, go to > > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > > and follow the instructions there. > > > > -- > --Eric > _________________________________________ > Eric Garner > > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
