Hi Alan, finally I solved the issue removing the 1121 board from the pts3200 and putting a 1121 board from a pts160 and now works perfect.
Looks that the unit have some customizations from the manufacturer. Thanks for all guys. 73! Iban eb3frn On Sat, Mar 2, 2013 at 5:02 PM, Alan Melia <[email protected]> wrote: > Hi Iban well my knowledge of the older generation is not much use to you > :-)) still I always think any response will bring more comments "out of the > woodwork" even if only to correct the false impressions. The suggestion of > of a faulty chip on that remote digit sounds like a worthwhile way to go. > > Good Luck with it these are useful units if a bit big by modern standards. > Best Wishes > > Alan > G3NYK > > ----- Original Message ----- From: "Iban Cardona" <[email protected]> > To: "Discussion of precise time and frequency measurement" > <[email protected]> > Sent: Saturday, March 02, 2013 12:37 AM > Subject: Re: [time-nuts] PTS 3200 remote programming > > > >> Hi Alan, >> >> thanks for answer. Yes I have the manual, but the latches on my pts >> not are as are showed in the user manual. Maybe my unit it is a >> different version or release, or have some customozation from the pts >> guys. >> >> In myunit, I tested the SO-2005 module that is that generates the >> 100Mhz decade, and I tested manually the 4bit to generate the 800Mhz >> and works well. >> >> My unit dont have front panel, only can be controllated remotelly. >> >> The differences from the user manual, is that un the user manual the >> 1ghz and 100mhz decade shares latch, and in my unit the shares latch >> the 100mhz with the 10mhz. The 1ghz latch is shared by the 1hz decade. >> >> Best regards >> >> 73! Iban >> eb3frn >> >> >> On Fri, Mar 1, 2013 at 8:27 PM, Alan Melia <[email protected]> >> wrote: >>> >>> Hi Iban do you have a manual? they are available. From memory because its >>> a >>> while since I worked on my Wavetek- Rockland unit I believe the remote >>> programming is in parallel with the front panel switches. The reason for >>> raising this is that there may be a problem on the back of the panel >>> switches.....mabe a wire off. Does the 800Mhz front panel switch setting >>> work correctly ?? >>> >>> Alan >>> G3NYK >>> >>> ----- Original Message ----- From: "Iban Cardona" <[email protected]> >>> To: <[email protected]> >>> Sent: Friday, March 01, 2013 6:42 PM >>> Subject: [time-nuts] PTS 3200 remote programming >>> >>> >>>> Hi, >>>> >>>> I'm traying to use to program the bcd interface of a PTS 3200. >>>> >>>> My truble us tha the 100Mhz decade 8 value bit is ignored by the PTS, >>>> then if I send 800Mhz to the PTS dont get output, and if send 900Mhz >>>> then I get 100Mhz. >>>> >>>> I checked the unit and the hardware looks OK. And my code is working >>>> well in another PTS units like the 620. >>>> >>>> The 3200 have some trick? >>>> >>>> Thanks for all >>>> >>>> 73! Iban >>>> eb3frn >>>> _______________________________________________ >>>> time-nuts mailing list -- [email protected] >>>> To unsubscribe, go to >>>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >>>> and follow the instructions there. >>> >>> >>> >>> _______________________________________________ >>> time-nuts mailing list -- [email protected] >>> To unsubscribe, go to >>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >>> and follow the instructions there. >> >> _______________________________________________ >> time-nuts mailing list -- [email protected] >> To unsubscribe, go to >> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >> and follow the instructions there. > > > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
