Hi There was a post from Goetz Romahn about a new version of Z38XX that will work correctly with the 3810/11/12. The previous version worked fine under XP. It’s a far better program to use than SatStat.
Bob > On Nov 7, 2014, at 3:48 PM, GandalfG8--- via time-nuts <[email protected]> > wrote: > > Which one are you using? > > The bottom one referred to on Didier's site is the old Windows 3 version, > perhaps even DOS, going back to 1993 or thereabouts. > > The later version is the one marked Satstat50, actually SatStat 5.0 and a > Symmetricom release from 2001. > > I can't try it on Win7 right now but did think I'd had it running > previously. > > Regards > > Nigel > GM8PZR > > > In a message dated 07/11/2014 20:42:26 GMT Standard Time, > [email protected] writes: > > It seems that this program will not work for Win 7. > Has anyone attempted to decompile this thing? > > Maybe re-work a bit and have it run on anything? > -George, N2FGX > > On 11/07/2014 01:34 PM, Bob Stewart wrote: >> Hi Bill, >> >> I think I got my copy here. I used the bottom one. I don't know what a > 58503 is. it was hard to find, for some reason. I'm using XP on an old > laptop. >> >> http://www.ko4bb.com/manuals/index.php?dir=05%29_GPS_Timing/SatStat >> Bob >> From: Bill Riches <[email protected]> >> To: 'Bob Stewart' <[email protected]>; 'Discussion of precise time and > frequency measurement' <[email protected]> >> Sent: Friday, November 7, 2014 7:04 AM >> Subject: RE: [time-nuts] Lucent KS-24361 GPSDO arrived today several > questions >> >> Hi Bob and group, >> >> Where are you obtaining Satstat and what windoze version will it work > on? XP, W7 32 or 64 bit? XP I guess? >> >> Bill Riches >> Cape May >> >> >> >> -----Original Message----- >> From: time-nuts [mailto:[email protected]] On Behalf Of Bob > Stewart >> Sent: Friday, November 07, 2014 12:03 AM >> To: Discussion of precise time and frequency measurement >> Subject: Re: [time-nuts] Lucent KS-24361 GPSDO arrived today several > questions >> >> Hi Bob, >> I've been using the Satstat program to send commands. What I don't > understand is why the slave will accept commands such as sat elevation angle > and not give an error response. It gives a response of "command complete", > but it doesn't change it. Or is that an indication that both units use the > same firmware, and success is actually indicated by the resulting change > of the angle? >> >> Bob From: Bob Camp <[email protected]> >> To: [email protected]; Discussion of precise time and frequency > measurement <[email protected]> >> Sent: Thursday, November 6, 2014 6:07 PM >> Subject: Re: [time-nuts] Lucent KS-24361 GPSDO arrived today several > questions >> >> >> --- >> This email is free from viruses and malware because avast! Antivirus > protection is active. >> http://www.avast.com >> >> >> >> _______________________________________________ >> time-nuts mailing list -- [email protected] >> To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >> and follow the instructions there. > > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
