For now I have uploaded KENWOOD TM-D710 setup pdf file to the files section of the Tracker2 group.
Larry K7YBZ --- In [email protected], "Erich J. Ritzmann" <ejr...@...> wrote: > > > This would be excellent material for the wiki... to drop a not so > subtle hint ;-) > > On 17-Oct-09, at 10:43 PM, k7ybz wrote: > > > > > > > --- In [email protected], "tbanks204" <tbanks204@> wrote: > >> > >> Received my cable today, how does on set up the Kenwood TM-710A for > >> use with the Nuvi 350. Thanks > >> > > > > I am assuming you mean the GTRANS cable for the Kenwood. > > > > Here are the general settings for the D710A. The SMARTBEACONING menu > > items and a few other choices are only available with the D710 > > firmware updates: TNC Version 1.01, OP Panel Version 2.01, Main > > Version 2.01. These can all be tweeked to your liking. > > > > Menu #600 BASIC > > Set the My CALLSIGN to your callsign and ssid > > Set the BEACON TYPE to eAPRSf > > > > Menu #601 TNC > > Set DATA BAND to A]BAND > > Set DATA SPEED to 1200 bps > > Set DCD SENSE to D or RxD BAND > > Set TX DELAY to 200 ms. > > > > Menu #602 GPS PORT > > Set Baud Rate: 4800 bps > > Set INPUT: GPS > > Set OUTPUT: WAYPOINT > > > > Menu #603 WAYPOINT > > Set FORMAT: KENWOOD > > Set NAME: 9]char > > Set OUTPUT: ALL > > > > Menu #606 BEACON INFORMATION > > Set SPEED : ON > > Set ALTITUDE : ON > > Set AMBIGUITY : OFF > > > > Menu #608 STATUS TEXT > > Pressing the MHZ button will put the flashing cursor to the left of > > a number between 1 and 5. Press eUSEf and an > > asterisk will be set between the cursor and the number. Pressing MHZ > > gets you to the sub menu items. > > In the TEXT FIELD, you can enter some text or leave blank. You can > > also set the text transmission rate: 1/1 or 1/3, etc. > > > > Menu #609 PACKET FILTER > > You might want to set the POSITION LIMIT to something like 50 or 100 > > miles to keep the noise down. For the TYPE just leave all the > > selections with an asterisk. > > > > #610 STATION ICON > > Select OTHERS > > Then select the appropriate SYMBOL and TABLE. It defaults to KENWOOD. > > > > Menu #611 BEACON TX ALGORITHM > > Set METHOD : Set to AUTO or SMARTBEACONING (Additional SMARTBEACONING > > settings are in menu #630 and menu #631) > > Set INITIAL INTERVAL : 2 (The manual only shows > > 0.2/0.5/1/3/5/10/20/30 minutes but there is a setting for 2 min > > with the latest firmware) > > Verify DECAY ALGORITHM : ON > > Verify PROPORTIONAL PATHING : ON > > > > Menu #612 PACKET PATH > > Set TYPE : Select eNEW]N PARADIGM and press eUSEf > > Set WIDE1]1 : Set to ON if you need to use a local digipeater to > > get to an IGATE > > Set TOTAL HOPS : Set to 2 unless you have WIDE1-1 on then set to 3 > > Verify PATH IS VIA: WIDE2]2 or WIDE1-1,WIDE2-2 depending on above > > settings. > > > > Menu #613 NETWORK > > Verify an asterisk is next to APRS. > > > > Menu #624 SOUND > > RX BEEP : OFF > > TX BEEP (BEACON) : OFF > > SPECIAL CALL : Blank > > APRS VOICE : OFF > > > > Menu #625 INTERRUPT DISPLAY > > Set per personal preference > > > > Menu #626 DISPLAY UNIT 1 > > Verify SPEED, DISTANCE : mi/h, mile > > Verify ALTITUDE, RAIN : feet, inch > > Verify TEMPERATURE : F > > > > Menu #630 SMARTBEACONING 1 > > Set LOW SPEED : 5 > > Set HIGH SPEED : 60 > > Set SLOW RATE : 10 MIN (600 seconds) > > Set FAST RATE : 120 SEC > > > > Menu #631 SMARTBEACONING 2 > > You can leave as is to begin with but I prefer: > > Set TURN ANGLE : 40 DEG > > Verify SLOPE : 26 (10 DEG/SPEED) > > Set TURN TIME : 60 > > > > > > > > Larry > > K7YBZ > > > > > > > > ------------------------------------ > > > > Yahoo! Groups Links > > > > > > > > -- > Erich J. Ritzmann >
