On 07/21/2017 02:34 PM, Bin Meng wrote: > Hi Marek, > > On Fri, Jul 21, 2017 at 6:06 PM, Marek Vasut <[email protected]> wrote: >> On 07/21/2017 12:04 PM, Bin Meng wrote: >>> Hi Marek, >>> >>> On Fri, Jul 21, 2017 at 4:56 PM, Marek Vasut <[email protected]> wrote: >>>> On 07/21/2017 10:54 AM, Bin Meng wrote: >>>>> Hi Marek, >>>>> >>>>> On Thu, Jul 20, 2017 at 8:20 PM, Marek Vasut <[email protected]> wrote: >>>>>> On 07/20/2017 02:16 PM, Bin Meng wrote: >>>>>>> Hi Marek, >>>>>>> >>>>>>> On Thu, Jul 20, 2017 at 7:12 AM, Bin Meng <[email protected]> wrote: >>>>>>>> This series is the final series of the xHCI driver update. >>>>>>>> >>>>>>>> This adds the missing interrupt transfer support to xHCI driver, so >>>>>>>> that devices like USB keyboard that uses interrupt transfer when >>>>>>>> CONFIG_SYS_USB_EVENT_POLL is defined can work. >>>>>>>> >>>>>>>> This also adds full speed device support. Unlike low/high/super speed >>>>>>>> devices, full speed device may report its endpoint 0 max packet size >>>>>>>> as 8/16/32/64. xHCI driver guesses 64 for the first attempt to get the >>>>>>>> initial 8 bytes device descriptor, and later adjusts the context for >>>>>>>> endpoint 0. >>>>>>>> >>>>>>>> This series also made several updates to xHCI driver to conform with >>>>>>>> the spec. >>>>>>>> >>>>>>>> Previous two series: >>>>>>>> [1]: usb: xhci: Fix USB xHCI support on Intel platform >>>>>>>> https://lists.denx.de/pipermail/u-boot/2017-June/296166.html >>>>>>>> [2]: usb: hub: Support USB 3.0 hubs >>>>>>>> https://lists.denx.de/pipermail/u-boot/2017-June/296284.html >>>>>>>> >>>>>>>> This series is available at u-boot-x86/xhci-working3 for testing. >>>>>>>> >>>>>>>> Changes in v3: >>>>>>>> - rebase on u-boot-usb/master >>>>>>>> - add changes to poplar.h >>>>>>>> >>>>>>>> Bin Meng (13): >>>>>>>> usb: xhci: Add interrupt transfer support >>>>>>>> usb: configs: Clean up CONFIG_SYS_USB_EVENT_POLL_(xxx) in board >>>>>>>> configs >>>>>>>> usb: kbd: kconfig: Set a default polling mechanism for USB keyboard >>>>>>>> usb: Only get 64 bytes device descriptor for full speed devices >>>>>>>> usb: Read device descriptor after device is addressed for xHCI >>>>>>>> usb: xhci: Fix max packet size for full speed device endpoint 0 >>>>>>>> usb: hub: Clear port reset before usb_hub_port_connect_change() >>>>>>>> usb: hub: Clear BH reset status change for a 3.0 hub >>>>>>>> usb: Handle audio extension endpoint descriptor in usb_parse_config() >>>>>>>> usb: xhci: Honor endpoint's interval >>>>>>>> usb: xhci: Program max burst size for endpoint >>>>>>>> usb: xhci: Set 'Error Count' to 0 for isoch endpoints >>>>>>>> usb: xhci: Set 'Average TRB Length' to 8 for control endpoints >>>>>>>> >>>>>>> >>>>>>> This is the last xHCI series I have. Can you please take a look and >>>>>>> apply? >>>>>> >>>>>> I'd like to see some RB/TB from Stefan Roese first if possible. >>>>>> >>>>> >>>>> OK, if that's the case, can you send a pull request to Tom to get usb >>>>> in? So that I can apply Stefan's x86 patch series on top of this. (I >>>>> cannot send PR for x86 before the usb changes) >>>> >>>> I actually cannot because the USB is currently broken, sorry, I'm >>>> waiting for a fix before I do that. >>>> >>>> Stefan, can you look at this series please? >>> >>> What "broken" issues are you seeing? >> >> I think Layerscape stopped building. Look at email with this subject >> "Compile failure encountered on latest (2017-07-20) >> git://git.denx.de/u-boot-usb.git branch master for target >> ls1021atwr_nor_defconfig" > > I see Patrice is working on a fix for the build failure.
Correct, it's almost done. Sorry for the delay. -- Best regards, Marek Vasut _______________________________________________ U-Boot mailing list [email protected] https://lists.denx.de/listinfo/u-boot
