It is possible that there is some sort of incompatibility.. rare but possible. since you have it setup as a test lab.. .do you have another RB2011 ? that you can test with (i.e. 2011 to 2011) ?
Regards, Faisal Imtiaz Snappy Internet & Telecom 7266 SW 48 Street Miami, FL 33155 Tel: 305 663 5518 x 232 Help-desk: (305)663-5518 Option 2 or Email: [email protected] ----- Original Message ----- > From: "Jeff Evans" <[email protected]> > To: "Ubiquiti Users Group" <[email protected]> > Sent: Tuesday, September 13, 2016 7:45:49 AM > Subject: Re: [Ubnt_users] RB2011UiAS -- FiberPOE sfp woes > Faisal etal, > > I've looped both sides, they act as they should, the fiberPoe gets it's > link light and the router is sending and receiving, however when I put > fiber between the two devices, I only see Tx packets on the sfp port. > obviously the patch cables are ok and the sfp modules are ok, so it must > be one of the devices doesn't like something?? I'm at a loss as to what > to do / try now. > > Regards, Jeff > > > On 9/12/2016 9:46 PM, Jeff Evans wrote: >> Should have mentioned, I have this 'labbed' up on living room floor, all >> duplicate equipment, save for the router. >> >> I was wanting to use a single strand, but have more available. >> >> Tx Power is -3.798 if this is what you are looking for. >> >> Rx Power is -4.398 >> >> that is on a short length of fiber (factory jumper) >> >> >> On 9/12/2016 9:28 PM, Faisal Imtiaz wrote: >>> some troubleshooting suggestions:- >>> >>> 1) Take the RB2011 closer to the fiberpoE and test it with a short patch >>> cable. >>> 2) Create a loop by connecting the far side connectors together and see you >>> get >>> link up ? (tough to do with bidi/single strand of fiber). >>> 3) invest in an in-expensive light meter ... (approx $50) will do the job. >>> 4) can you read light TX & receive levels on the MT ? >>> >>> BTW what kind of fiber are you using ? >>> Based on the optics listed, are you trying to use a single strand of fiber ? >>> >>> Regards >>> >>> Faisal Imtiaz >>> Snappy Internet & Telecom >>> 7266 SW 48 Street >>> Miami, FL 33155 >>> Tel: 305 663 5518 x 232 >>> >>> Help-desk: (305)663-5518 Option 2 or Email: [email protected] >>> >>> ----- Original Message ----- >>>> From: "Jeff Evans" <[email protected]> >>>> To: "Ubiquiti Users Group" <[email protected]> >>>> Sent: Monday, September 12, 2016 8:34:59 PM >>>> Subject: [Ubnt_users] RB2011UiAS -- FiberPOE sfp woes >>>> I have an RB2011UiAS that I want to use for a customers home router, we >>>> have an 800 foot fiber run to a ubnt FiberPOE. Any modules I've tried >>>> only show Tx on the Interface, I have also tried the modules on a >>>> Netonix switch (replacing the FiberPoe) with the same result. >>>> >>>> The fiber modules that I have tried : Mikrotik S35LC20D/S53LC20D pair -- >>>> MAXXwave MW-1315-SM-US/MW-1513-SM-US pair >>>> the above both give me the blue light of success on the >>>> FiberPOE but no real joy. >>>> >>>> AND a set of Maxxwave MW-LX-SM-US -- dual fiber, no light on the >>>> FiberPOE with this. >>>> >>>> any ideas? Thanks! >>>> >>>> -- >>>> Jeff Evans, Managing Member >>>> PennWisp, LLC >>>> www.pennwisp.com >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>> _______________________________________________ >>> Ubnt_users mailing list >>> [email protected] >>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>> > > -- > Jeff Evans, Managing Member > PennWisp, LLC > www.pennwisp.com > > _______________________________________________ > Ubnt_users mailing list > [email protected] > http://lists.wispa.org/mailman/listinfo/ubnt_users _______________________________________________ Ubnt_users mailing list [email protected] http://lists.wispa.org/mailman/listinfo/ubnt_users
