Shaping works best on egress interfaces. Tower router controls download speeds, upload speeds are shaped on the WAN port of the CPE radio.
On Tue, Aug 22, 2017 at 7:59 AM, Troy Gibson, Byhalia.net <[email protected]> wrote: > Steve, > > Thats a good idea to test. Never set one up on the CPE. I see the area > on the network tab, but not 100% how to set up and down limits on it. Is > there a protocol to use so the settings function correctly? > > Thanks, > > Troy > > > > Sent from my Verizon, Samsung Galaxy smartphone > > -------- Original message -------- > From: Steve Barnes <[email protected]> > Date: 8/21/17 10:40 PM (GMT-05:00) > To: Ubiquiti Users Group <[email protected]> > Subject: Re: [Ubnt_users] Erratic downloads and uploads, PBE-M5-400 > > Try taking the queue off the Mtik and settIng it on the cpe > > Steve Barnes > > -----Original Message----- > From: [email protected] [mailto:[email protected]] > On Behalf Of [email protected] > Sent: Monday, August 21, 2017 2:33 PM > To: [email protected] > Subject: [Ubnt_users] Erratic downloads and uploads, PBE-M5-400 > > Time to ask the experts as I cannot figure out this issue!! This CPE > worked perfect until a recent storm, but I have replaced the AP and CPE > radios at this point too. > > I have one customer that reports erratic download and uploads. Actually > sometimes going above the set rate in my Tik router, CCR1009-7G-1C+PC, > Firmware Bugfix 6.38.7. This CPE is connected to an AP that is feed from > routers that are directly connected to my fiber line in my Data Center in > this area, so everything is at the base of the tower that feeds this AP > directly, no jumps to other towers first. > > I spent a lot of time connected to this CPE at the customers house testing > with and without airmax, changing radio firmware, decreasing and increasing > power, but get the same erratic behavior. I changed the POE, > M5 cone tested the cable (tested good), but still the same. I finally > tested multiple channels at the AP and found a stable solution/temp fix, > not perfect, but stable. I had to leave the CPE unlimited as it was still > not behaving correctly so for the trouble I left it unlimited to buy time > to figure this out. I even stopped at some other customers on that same > road and AP and those tested like it should at the rate it was set to in > the Tik router. > > Customer has been great during this time and sending me samples of > speedtests at different times in the day. Still getting big swings in > speeds that vary and when I check AirControl it does not even match the > speeds they are reporting. I'm using AC 2.1 beta 7. I realize the > unlimited setup could impact their tests, but why is AC2 not showing > anything even close to their speedtests? > > Below are the radio stats for this CPE. I attached a word file of the M5 > radio stats as the copied image would not paste correctly on this email. > > Signal: -56dBm > H/V: -59/-58 dBm > > Transmit CCQ: 93% > TX/RX: 72.222mbps/72.222mbps > Firmware 5.6.15 XW > > Airmax is enabled and shows 96% for both. > > Channel Width: 10mhz > Channel Freq: 5805 > Distance is 1.7 miles > TX power 26 > > Access Point is on 5.6.15 XW firmware > > Thank you for your support!! > > Troy Gibson > > Byhalia.net, LLC > _______________________________________________ > Ubnt_users mailing list > [email protected] > http://lists.wispa.org/mailman/listinfo/ubnt_users > > _______________________________________________ > Ubnt_users mailing list > [email protected] > http://lists.wispa.org/mailman/listinfo/ubnt_users > > -- Kurt Albershardt | Mimbres Communications, LLC | 575-342-0042
_______________________________________________ Ubnt_users mailing list [email protected] http://lists.wispa.org/mailman/listinfo/ubnt_users
