Sam Why only Egress? We use Egress and Ingress both and have no issue. Steve Barnes Wireless Operations Manager New Lisbon Broadband NLBC.COM PCSWIN.COM 765-584-2288 ext:1101
From: [email protected] [mailto:[email protected]] On Behalf Of Sam Tetherow Sent: Tuesday, August 22, 2017 10:37 AM To: [email protected] Subject: Re: [Ubnt_users] Erratic downloads and uploads, PBE-M5-400 Use egress only. LAN egress is download, WLAN egress is upload. On 08/22/2017 08:59 AM, Troy Gibson, Byhalia.net wrote: Steve, Thats a good idea to test. Never set one up on the CPE. I see the area on the network tab, but not 100% how to set up and down limits on it. Is there a protocol to use so the settings function correctly? Thanks, Troy Sent from my Verizon, Samsung Galaxy smartphone -------- Original message -------- From: Steve Barnes <[email protected]><mailto:[email protected]> Date: 8/21/17 10:40 PM (GMT-05:00) To: Ubiquiti Users Group <[email protected]><mailto:[email protected]> Subject: Re: [Ubnt_users] Erratic downloads and uploads, PBE-M5-400 Try taking the queue off the Mtik and settIng it on the cpe Steve Barnes -----Original Message----- From: [email protected]<mailto:[email protected]> [mailto:[email protected]] On Behalf Of [email protected]<mailto:[email protected]> Sent: Monday, August 21, 2017 2:33 PM To: [email protected]<mailto:[email protected]> Subject: [Ubnt_users] Erratic downloads and uploads, PBE-M5-400 Time to ask the experts as I cannot figure out this issue!! This CPE worked perfect until a recent storm, but I have replaced the AP and CPE radios at this point too. I have one customer that reports erratic download and uploads. Actually sometimes going above the set rate in my Tik router, CCR1009-7G-1C+PC, Firmware Bugfix 6.38.7. This CPE is connected to an AP that is feed from routers that are directly connected to my fiber line in my Data Center in this area, so everything is at the base of the tower that feeds this AP directly, no jumps to other towers first. I spent a lot of time connected to this CPE at the customers house testing with and without airmax, changing radio firmware, decreasing and increasing power, but get the same erratic behavior. I changed the POE, M5 cone tested the cable (tested good), but still the same. I finally tested multiple channels at the AP and found a stable solution/temp fix, not perfect, but stable. I had to leave the CPE unlimited as it was still not behaving correctly so for the trouble I left it unlimited to buy time to figure this out. I even stopped at some other customers on that same road and AP and those tested like it should at the rate it was set to in the Tik router. Customer has been great during this time and sending me samples of speedtests at different times in the day. Still getting big swings in speeds that vary and when I check AirControl it does not even match the speeds they are reporting. I'm using AC 2.1 beta 7. I realize the unlimited setup could impact their tests, but why is AC2 not showing anything even close to their speedtests? Below are the radio stats for this CPE. I attached a word file of the M5 radio stats as the copied image would not paste correctly on this email. Signal: -56dBm H/V: -59/-58 dBm Transmit CCQ: 93% TX/RX: 72.222mbps/72.222mbps Firmware 5.6.15 XW Airmax is enabled and shows 96% for both. Channel Width: 10mhz Channel Freq: 5805 Distance is 1.7 miles TX power 26 Access Point is on 5.6.15 XW firmware Thank you for your support!! Troy Gibson Byhalia.net, LLC _______________________________________________ Ubnt_users mailing list [email protected]<mailto:[email protected]> http://lists.wispa.org/mailman/listinfo/ubnt_users _______________________________________________ Ubnt_users mailing list [email protected]<mailto:[email protected]> http://lists.wispa.org/mailman/listinfo/ubnt_users
_______________________________________________ Ubnt_users mailing list [email protected] http://lists.wispa.org/mailman/listinfo/ubnt_users
