Jordan Share <[EMAIL PROTECTED]> writes: > A couple of bugs: > > First, some of the directories under "os" have long filenames. This > is fine with the dos boot disk, presumably because it mangles them the > same for winnt as it does for install.pl. > > Under linux, though, the initial installer gets told to copy files > from "win2kServer", which doesn't work in dosemu.
Rename the directories to use shorter names. :-) We can probably fix this by implementing name-mangling ourselves, using the mangled names in the portions of the install which are run by DOS. Maybe just doit.bat. This strikes me as a fair bit of work for only moderate gain. Feel like opening a formal bug tracking ticket? > Another problem I'm running into is when it tries to copy my driver > files over. > > I am getting the error: > > Setup was unable to copy the following file: > > IA32 > > o press ENTER to retry the copy operation > [ etc. ] > > I did a find in the os directory and this is the only hit: > ./win2ksp4/I386/$oem$/$1/drivers/shuttle/LAN/Windows/Drivers/IA32 The exact same directory works when copied from DOS? And the failure happens on all of your machines, or only with the 160G disk you mention below? Can you put a tarred copy of drivers/shuttle someplace where I can download it? I would like to try to reproduce this myself. > IA32 is the only one it complains about. Perhaps it is too deep? Perhaps. FreeDOS bug, maybe. > When it first detects the drive (a 160gig drive), I get various errors > in the style of: > Odd. C/H/S does not multiply out to 312581808. > > Setting C/H/S for hda to 19457/255/63...done. This is not really an error; I get something similar on a couple of machines. It just means the total drive size is not an integral number of cylinders, where a "cylinder" is 512 bytes times H times S. The cylinder count is not terribly important; it is the head and sector counts that matter. > The boot output is: > hda: ST3160021A, ATA DISK drive > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > hda: max request size: 1024KiB > hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63, These CHS values and drive size agree with ours, which I suppose is good. > UDMA(100) > hda: hda1 > > These CHS values do not correspond to what the BIOS thinks the drive > is. We query the BIOS for the "legacy" geometry (H and S only), and then compute C from those plus the drive size. If you change your BIOS setting, you should see the values we report change as well. How was your BIOS set to when you performed this test? > Here's the BIOS settings, and what it ends up with for C/H/S with each > of them: > > CHS -- 65535/16/255 With H/S of 16/255, the drive is too big to fit even with the cylinder count maxed out. So they max out the cylinder count, which makes sense. > LBA -- 16643/255/63 This is just wrong. 16643*255*63*512 == 136G, not 160. Hm... That does pretty much agree with CHS == 65535/16/255. I wonder what is going on here. > Large -- 4095/240/255 No idea where this is coming from. > Auto -- 65535/16/255 (same as CHS) > This might be related to the next problem... > > ---- > Finally, (after skipping the copy of IA32), It reboots and I end up with: > Setup cannot find the temporary installation files. > > The hard drive on which Setup placed temporary files is not > currently available to Windows 2000. You may need a > ... > [ snip ] Questions: Does this system install OK when you use the DOS boot disk? Have you tried using this hard drive (or any >137G drive) in a different computer? Did you change the BIOS settings between the initial boot and the execution of Windows Setup? (Unlikely, but I had to ask...) Did you allow Unattended to partition the drive automatically? I still do not see what is going on. The initial partition should be a 4G FAT partition. Even if our cylinder count is too large, we should be fine. Two things you might try. First, experiment with different BIOS settings (LARGE/LBA/CHS). Each time you change, be sure to allow Unattended to replace the partition table, though. Second, try partitioning the disk under DOS, then booting to Linux and choosing "do nothing" for the partitioning step. If that works, we can debug from there. - Pat ------------------------------------------------------- This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click _______________________________________________ unattended-devel mailing list [EMAIL PROTECTED] https://lists.sourceforge.net/lists/listinfo/unattended-devel
