I travel quite a bit for work- If I am ever in MA- I will shout On Sun, Aug 15, 2010 at 4:42 PM, Perry & Cindi <[email protected]> wrote:
> I live north of Boston MA. Feel free to send me a round trip ticket to > visit, HA, HA > > Good luck with your boat. > > Capt. Perry > > > ------------------------------ > > *From:* [email protected] [mailto: > [email protected]] *On Behalf Of *Maureen Washburn > *Sent:* Saturday, August 14, 2010 9:11 PM > *To:* [email protected] > *Subject:* Re: [UnifliteWorld] Bonding/Cathodic Protection Again > > > > Cap'n > You are quite a fount of knowledge- are you anywhere near Dallas TX? I > would pay to have you visit and inspect our old tub-OR- I would love to > visit you and your boat! > You obviously have a love of and great experience with these uni's- I would > love to sit at your feet and learn! I am generally a very competent soul > UNTIL I step aboard our DCMY-it no doubt needs more than I capable of > providing it! > > On Sat, Aug 14, 2010 at 12:14 PM, Perry & Cindi <[email protected]> > wrote: > > NO, you do not remove the 4 bolts! > > On each of the 4 bolts that goes thru the transom there should be a flat > washer and a locking nut that holds the bolt in place on the outside of the > transom. After that nut there should be another flat washer that the house > zinc buts up to and then another washer and nut to hold the zinc in place. > Unless one of the bolts is seeping water, do not disturb them. > > I did not get your attachment > Capt. Perry > > > -----Original Message----- > From: [email protected] [mailto: > [email protected]] > On Behalf Of mvcompromise > Sent: Saturday, August 14, 2010 12:31 PM > To: UnifliteWorld > Subject: [UnifliteWorld] Bonding/Cathodic Protection Again > > Hi All, > > Thanks for your reply's on my previous questions on bonding. I have a > 42' DCMY with 2 transom zincs. They appear to be attached by a bolt > through a backing plate then hull so to replace the terminal you have > to remove the bolt from the backing plate and hull? Therefore out of > the water and then reseal the bolts. I have added a picture in files > (100-0871) that shows 1 of the bolts attached to the backing and > hull. Could Uniflite have done it this way so you have to remove the > bolts from the transom? Thanks again for any help. > > Red > > -- > You received this message because you are subscribed to the Google Groups > "UnifliteWorld" group. > To post to this group, send email to [email protected]. > To unsubscribe from this group, send email to > [email protected]<unifliteworld%[email protected]> > . > For more options, visit this group at > http://groups.google.com/group/unifliteworld?hl=en. > > -- > You received this message because you are subscribed to the Google Groups > "UnifliteWorld" group. > To post to this group, send email to [email protected]. > To unsubscribe from this group, send email to > [email protected]<unifliteworld%[email protected]> > . > For more options, visit this group at > http://groups.google.com/group/unifliteworld?hl=en. > > > > > -- > Maureen Washburn, ND, RN, CPHQ, FACHE > [email protected] > 817-797-7707 > > -- > You received this message because you are subscribed to the Google Groups > "UnifliteWorld" group. > To post to this group, send email to [email protected]. > To unsubscribe from this group, send email to > [email protected]<unifliteworld%[email protected]> > . > For more options, visit this group at > http://groups.google.com/group/unifliteworld?hl=en. > > -- > You received this message because you are subscribed to the Google Groups > "UnifliteWorld" group. > To post to this group, send email to [email protected]. > To unsubscribe from this group, send email to > [email protected]<unifliteworld%[email protected]> > . > For more options, visit this group at > http://groups.google.com/group/unifliteworld?hl=en. > -- Maureen Washburn, ND, RN, CPHQ, FACHE [email protected] 817-797-7707 -- You received this message because you are subscribed to the Google Groups "UnifliteWorld" group. To post to this group, send email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/unifliteworld?hl=en.
