AND THIS VIA DMESG SECTION OF THE DIAGNOSTIC PAGE (PART 3 OF 3) [ 0.935424] Non-periodic Split Transactions [ 0.935424] Periodic Split Transactions [ 0.935424] High-Speed Isochronous Endpoints [ 0.935424] Interrupt/Control Split Transaction hack enabled [ 0.935431] dwc_otg: Microframe scheduler enabled [ 0.935487] WARN::hcd_init_fiq:459: FIQ on core 1 at 0x805d26f8 [ 0.935497] WARN::hcd_init_fiq:460: FIQ ASM at 0x805d2a60 length 36 [ 0.935507] WARN::hcd_init_fiq:486: MPHI regs_base at 0xbe87e000 [ 0.935560] dwc_otg 3f980000.usb: DWC OTG Controller [ 0.935594] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1 [ 0.935629] dwc_otg 3f980000.usb: irq 62, io mem 0x00000000 [ 0.935672] Init: Port Power? op_state=1 [ 0.935676] Init: Power Port (0) [ 0.935896] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.935906] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.935913] usb usb1: Product: DWC OTG Controller [ 0.935920] usb usb1: Manufacturer: Linux 4.14.26-pcpCore_v7 dwc_otg_hcd [ 0.935927] usb usb1: SerialNumber: 3f980000.usb [ 0.936525] hub 1-0:1.0: USB hub found [ 0.936568] hub 1-0:1.0: 1 port detected [ 0.937053] dwc_otg: FIQ enabled [ 0.937058] dwc_otg: NAK holdoff enabled [ 0.937061] dwc_otg: FIQ split-transaction FSM enabled [ 0.937071] Module dwc_common_port init [ 0.937308] usbcore: registered new interface driver usb-storage [ 0.937505] mousedev: PS/2 mouse device common for all mice [ 0.937571] IR NEC protocol handler initialized [ 0.937576] IR RC5(x/sz) protocol handler initialized [ 0.937580] IR RC6 protocol handler initialized [ 0.937583] IR JVC protocol handler initialized [ 0.937587] IR Sony protocol handler initialized [ 0.937591] IR SANYO protocol handler initialized [ 0.937595] IR Sharp protocol handler initialized [ 0.937599] IR MCE Keyboard/mouse protocol handler initialized [ 0.937603] IR XMP protocol handler initialized [ 0.938263] bcm2835-wdt 3f100000.watchdog: Broadcom BCM2835 watchdog timer [ 0.938503] bcm2835-cpufreq: min=600000 max=900000 [ 0.939495] sdhci: Secure Digital Host Controller Interface driver [ 0.939500] sdhci: Copyright(c) Pierre Ossman [ 0.939827] sdhost-bcm2835 3f202000.mmc: could not get clk, deferring probe [ 0.939930] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.940417] ledtrig-cpu: registered to indicate activity on CPUs [ 0.940518] hidraw: raw HID events driver (C) Jiri Kosina [ 0.940668] usbcore: registered new interface driver usbhid [ 0.940673] usbhid: USB HID core driver [ 0.941245] vchiq: vchiq_init_state: slot_zero = bdd80000, is_master = 0 [ 0.942737] [vc_sm_connected_init]: start [ 0.946049] vc_vchi_sm_init: failed to open VCHI service (-1) [ 0.946057] [vc_sm_connected_init]: failed to initialize shared memory service [ 0.946065] [vc_sm_connected_init]: end - returning -1 [ 0.946696] Initializing XFRM netlink socket [ 0.946720] NET: Registered protocol family 17 [ 0.946812] Key type dns_resolver registered [ 0.947229] Registering SWP/SWPB emulation handler [ 0.947838] registered taskstats version 1 [ 0.953165] uart-pl011 3f201000.serial: cts_event_workaround enabled [ 0.953249] 3f201000.serial: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2 [ 0.955092] sdhost: log_buf @ bdd13000 (fdd13000) [ 1.031693] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1) [ 1.032656] of_cfs_init [ 1.032823] of_cfs_init: OK [ 1.053065] Freeing unused kernel memory: 1024K [ 1.160863] mmc0: host does not support reading read-only switch, assuming write-enable [ 1.161863] Indeed it is in host mode hprt0 = 00021501 [ 1.222754] mmc0: new high speed SDHC card at address aaaa [ 1.223497] mmcblk0: mmc0:aaaa SL32G 29.7 GiB [ 1.225492] mmcblk0: p1 p2 [ 1.381770] usb 1-1: new high-speed USB device number 2 using dwc_otg [ 1.381977] Indeed it is in host mode hprt0 = 00001101 [ 1.632067] usb 1-1: New USB device found, idVendor=0424, idProduct=9514 [ 1.632084] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 1.632765] hub 1-1:1.0: USB hub found [ 1.632890] hub 1-1:1.0: 5 ports detected [ 1.951806] usb 1-1.1: new high-speed USB device number 3 using dwc_otg [ 2.081861] Under-voltage detected! (0x00050005) [ 2.082197] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00 [ 2.082212] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.085253] smsc95xx v1.0.6 [ 2.176211] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:31:37:8c [ 2.471723] usb 1-1.5: new high-speed USB device number 4 using dwc_otg [ 2.602592] usb 1-1.5: New USB device found, idVendor=20b1, idProduct=3023 [ 2.602607] usb 1-1.5: New USB device strings: Mfr=1, Product=3, SerialNumber=0 [ 2.602617] usb 1-1.5: Product: S16 USB DAC [ 2.602628] usb 1-1.5: Manufacturer: aune [ 2.607380] input: aune S16 USB DAC as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.5/1-1.5:1.4/0003:20B1:3023.0001/input/input0 [ 2.672029] hid-generic 0003:20B1:3023.0001: input,hidraw0: USB HID v1.10 Device [aune S16 USB DAC] on usb-3f980000.usb-1.5/input4 [ 3.907353] zram: Added device: zram0 [ 3.942151] zram0: detected capacity change from 0 to 247705600 [ 3.957032] Adding 241896k swap on /dev/zram0. Priority:-2 extents:1 across:241896k SSFS [ 4.153267] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 4.753529] EXT4-fs (mmcblk0p2): recovery complete [ 4.754852] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 4.881191] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 8.311857] Voltage normalised (0x00000000) [ 8.466992] usbcore: registered new interface driver snd-usb-audio [ 8.874403] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 10.407188] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC5E1 [ 15.202765] random: crng init done
Then I went back in the Squeezelite settings (Squeezelite was still running with disabled onboard card) and now - hell know why - I could see all kinds of outputs devices inlcuding the one i usually use. 25888 After choosing the right output- and the other settings, followed by the restart everything seems to work again. Sounds is back again. Still not sure why but at least it´s there again. But now I´m hesitating going back to v4.0.0. Or do you know the reason for this - from my point of view - strange behaviour? Thanks again for your support. Cheers, Markus +-------------------------------------------------------------------+ |Filename: 2018-11-03 10_42_20-pCP - Squeezelite Settings.png | |Download: http://forums.slimdevices.com/attachment.php?attachmentid=25888| +-------------------------------------------------------------------+ ------------------------------------------------------------------------ marflao's Profile: http://forums.slimdevices.com/member.php?userid=57334 View this thread: http://forums.slimdevices.com/showthread.php?t=109404
_______________________________________________ unix mailing list [email protected] http://lists.slimdevices.com/mailman/listinfo/unix
