We have a problem in Kannel with opening a "new" (i.e., after a boot) serial device.
opening the device first using minicom (just open it and then close minicom - you
don't need to issue any commands) before running Kannel will solve the problem.
We are working on a fix, but as we are not sure what the problem is - I cannot give a
time estimate.
--
Oded Arbel
m-Wise Mobile Solutions
[EMAIL PROTECTED]
Mobile: +972-67-340014
Tel: +972-9-9581711 (ext: 116)
::..
"Where time or intelligence are lacking, a goto may do the job."
-- M.E. Hopkins, "A Case for the GOTO," 1972.
> -----Original Message-----
> From: Martin, Kenn [mailto:[EMAIL PROTECTED]]
> Sent: Wednesday, June 19, 2002 9:59 AM
> To: '[EMAIL PROTECTED]'
> Subject: RE: TC-35 Startup
>
>
> I have the same problem with a Nokia 6210. The system was
> working perfectly
> until a power cut. When the power was restored I see the
> results as below. I
> don't think the cable is the answer.
>
> Kenn
>
> -----Original Message-----
> From: Richard Bowen [mailto:[EMAIL PROTECTED]]
> Sent: 19 June 2002 08:50
> To: [EMAIL PROTECTED]; [EMAIL PROTECTED]
> Subject: Re: TC-35 Startup
>
>
> Thomas
>
> I had the same problem, make sure the speed setting is equal
> to 19200 in
> both the smsc at2 group and the modem group. If not it might
> be your serial
> cable.
>
> Rich
>
> >>> Tampier Thomas <[EMAIL PROTECTED]> 06/18/02 23:45 PM >>>
> Hi list,
>
> i have troubles starting my Siemens TC35. Every time i try to
> start the
> bearerbox i get this log (i tried all possible configurations in
> kannel.conf, its always the same) --> any ideas?
>
> thx for your help
> Thomas
>
> 2002-06-19 00:38:30 [5] INFO: AT2[/dev/ttyS0]: speed set to 19200
> 2002-06-19 00:38:30 [5] DEBUG: AT2[/dev/ttyS0]: --> ^M
> 2002-06-19 00:38:32 [5] DEBUG: AT2[/dev/ttyS0]: --> AT^M
> 2002-06-19 00:38:36 [5] DEBUG: AT2[/dev/ttyS0]: --> AT^M
> 2002-06-19 00:38:40 [5] DEBUG: AT2[/dev/ttyS0]: -->AT^M
> 2002-06-19 00:38:44 [5] INFO: AT2[/dev/ttyS0]: closing device
> 2002-06-19 00:38:44 [5] INFO: AT2[/dev/ttyS0]: opening device
> 2002-06-19 00:38:44 [5] DEBUG: AT2[/dev/ttyS0]: device opened
> 2002-06-19 00:38:44 [5] INFO: AT2[/dev/ttyS0]: speed set to 9600
> 2002-06-19 00:38:44 [5] DEBUG: AT2[/dev/ttyS0]: --> ^M
> 2002-06-19 00:38:46 [5] DEBUG: AT2[/dev/ttyS0]: --> AT^M
> 2002-06-19 00:38:50 [5] DEBUG: AT2[/dev/ttyS0]: --> AT^M
> 2002-06-19 00:38:54 [5] DEBUG: AT2[/dev/ttyS0]: --> AT^M
> 2002-06-19 00:38:58 [5] INFO: AT2[/dev/ttyS0]: closing device
> 2002-06-19 00:38:58 [5] INFO: AT2[/dev/ttyS0]: cannot detect speed
> 2002-06-19 00:38:58 [5] DEBUG: Thread 5
> (gw/smsc_at2.c:at2_device_thread)
> terminates.
>
>
>
>
> _____________________________________________________________________
> This message has been checked for all known viruses by UUNET
> delivered
> through the MessageLabs Virus Control Centre. For further
> information visit
> http://www.uk.uu.net/products/security/virus/
>
>
> _____________________________________________________________________
> This message has been checked for all known viruses by UUNET
> delivered
> through the MessageLabs Virus Control Centre. For further
> information visit
> http://www.uk.uu.net/products/security/virus/
> **********************************************************************
> This Email and any files transmitted with it are confidential and
> intended solely for the use of the individual or entity to
> whom they
> are addressed. If you have received this Email in error please notify
> the system manager.
>
> This footnote also confirms that this Email message has been swept by
> MIMEsweeper and Norton Anti-Virus for the presence of
> computer viruses.
>
> **********************************************************************
> VISIT OUR WEBSITE AT HTTP://WWW.DOMINO-PRINTING.COM/
> **********************************************************************
>
>
