After trying, I can contact and send AT commands to my M20, with minicom.
Juxener wrote: > > Thanx Nikos. > I can send SMS with Gnokii, with /dev/ttyS0 device. My modem works... > > But I've found my issue : with speed 19200, it's works (the speed > attribute was redefined with 9600...) ! It's works... almost. > > Now, I've this issue : > > ju:/etc/kannel# bearerbox -v 0 /etc/kannel/sms.conf > 2009-09-05 18:20:06 [4205] [4] INFO: AT2[/dev/ttyS0]: opening device > 2009-09-05 18:20:06 [4205] [4] DEBUG: AT2[/dev/ttyS0]: device opened > 2009-09-05 18:20:07 [4205] [4] DEBUG: AT2[/dev/ttyS0]: device opened > 2009-09-05 18:20:07 [4205] [4] INFO: AT2[/dev/ttyS0]: init device > 2009-09-05 18:20:07 [4205] [4] INFO: AT2[/dev/ttyS0]: speed set to 19200 > 2009-09-05 18:20:08 [4205] [4] DEBUG: AT2[/dev/ttyS0]: --> ATZ^M > 2009-09-05 18:20:08 [4205] [4] DEBUG: AT2[/dev/ttyS0]: <-- OK > 2009-09-05 18:20:08 [4205] [4] DEBUG: AT2[/dev/ttyS0]: --> AT^M > 2009-09-05 18:20:08 [4205] [4] DEBUG: AT2[/dev/ttyS0]: <-- AT > 2009-09-05 18:20:08 [4205] [4] DEBUG: AT2[/dev/ttyS0]: <-- OK > 2009-09-05 18:20:08 [4205] [4] DEBUG: AT2[/dev/ttyS0]: --> AT&F^M > 2009-09-05 18:20:08 [4205] [4] DEBUG: AT2[/dev/ttyS0]: <-- AT&F > 2009-09-05 18:20:08 [4205] [4] DEBUG: AT2[/dev/ttyS0]: <-- OK > 2009-09-05 18:20:08 [4205] [4] DEBUG: AT2[/dev/ttyS0]: --> ATE0^M > 2009-09-05 18:20:08 [4205] [4] DEBUG: AT2[/dev/ttyS0]: <-- ATE0 > 2009-09-05 18:20:08 [4205] [4] DEBUG: AT2[/dev/ttyS0]: <-- OK > 2009-09-05 18:20:08 [4205] [4] DEBUG: AT2[/dev/ttyS0]: --> AT\Q3^M > 2009-09-05 18:20:08 [4205] [4] DEBUG: AT2[/dev/ttyS0]: <-- ERROR > 2009-09-05 18:20:08 [4205] [4] ERROR: AT2[/dev/ttyS0]: Generic error: > ERROR > 2009-09-05 18:20:08 [4205] [4] INFO: AT2[/dev/ttyS0]: cannot enable > hardware handshake > 2009-09-05 18:20:08 [4205] [4] DEBUG: AT2[/dev/ttyS0]: --> AT+CPIN?^M > 2009-09-05 18:20:08 [4205] [4] DEBUG: AT2[/dev/ttyS0]: <-- +CPIN: READY > 2009-09-05 18:20:08 [4205] [4] DEBUG: AT2[/dev/ttyS0]: <-- OK > 2009-09-05 18:20:08 [4205] [4] DEBUG: AT2[/dev/ttyS0]: --> AT+CMGF=0^M > 2009-09-05 18:20:09 [4205] [4] DEBUG: AT2[/dev/ttyS0]: <-- OK > 2009-09-05 18:20:09 [4205] [4] DEBUG: AT2[/dev/ttyS0]: --> AT+CSMS=?^M > 2009-09-05 18:20:09 [4205] [4] DEBUG: AT2[/dev/ttyS0]: <-- +CSMS: > (0,1,128) > 2009-09-05 18:20:09 [4205] [4] DEBUG: AT2[/dev/ttyS0]: <-- OK > 2009-09-05 18:20:09 [4205] [4] INFO: AT2[/dev/ttyS0]: Phase 2+ is > supported > 2009-09-05 18:20:09 [4205] [4] DEBUG: AT2[/dev/ttyS0]: --> AT+CSMS=1^M > 2009-09-05 18:20:09 [4205] [4] DEBUG: AT2[/dev/ttyS0]: <-- +CSMS: 1,1,1 > 2009-09-05 18:20:09 [4205] [4] DEBUG: AT2[/dev/ttyS0]: <-- OK > 2009-09-05 18:20:09 [4205] [4] DEBUG: AT2[/dev/ttyS0]: --> > AT+CNMI=1,2,0,1,0^M > 2009-09-05 18:20:09 [4205] [4] DEBUG: AT2[/dev/ttyS0]: <-- ERROR > 2009-09-05 18:20:09 [4205] [4] ERROR: AT2[/dev/ttyS0]: Generic error: > ERROR > 2009-09-05 18:20:09 [4205] [4] ERROR: AT2[/dev/ttyS0]: Opening failed. > Terminating > 2009-09-05 18:20:09 [4205] [4] INFO: AT2[/dev/ttyS0]: closing device > > In sms.conf, I have : > group = core > admin-port = 13000 > admin-password = bar > > group = modems > id = siemens_m20 > name = "Siemens M20" > detect-string = "SIEMENS" > detect-string2 = "M20" > speed = 19200 > enable-hwhs = "AT\\Q3" > keepalive-cmd = "AT+CBC;+CSQ" > need-sleep = true > > group = smsc > smsc = at > modemtype = siemens_m20 > device = /dev/ttyS0 > > group = smsbox > bearerbox-host = localhost > sendsms-port = 13013 > > group = sendsms-user > username = tester > password = foobar > > group = sendsms-user > username = kannel > password = rL4y > user-deny-ip = "*.*.*.*" > user-allow-ip = "127.0.0.1" > > group = sms-service > keyword = default > text = "No service specified" > > Thanx a lot, again. > > > > > Nikos Balkanas wrote: >> >> Hi, >> >> Your modem doesn't repond. Try the following: >> >> 1) dmesg | grep tty in Linux. grep tty /var/adm/messages in Solaris. >> Verify >> you have the correct device for your modem. >> >> 2) Using minicom or wvdial, connect to device from part (1) and type a >> simple AT. If you don't get a response you have a hardware problem (port, >> cable, modem). >> >> Configure correct parameters to kannel and retry. Assuming you have the >> correct device, and the modem doesn't respond to kannel, it is almost >> certainly case (2). >> >> BR, >> Nikos >> ----- Original Message ----- >> From: "Juxener" <[email protected]> >> To: <[email protected]> >> Sent: Saturday, September 05, 2009 3:42 PM >> Subject: Re: Send SMS with Siemens M20 on Linux >> >> >>> >>> Thank you for your answer. >>> >>> Since my last message, I've better results : with Gnokii, I can send SMS >>> ! >>> Gnokii is not interessant in it, but it proves that my M20 works (with >>> my >>> new SIM card). And it's configured with the /dev/ttyS0 device... >>> >>> Unfortunately, it doesn't works with Kannel... always the same error : >>> ju:~# bearerbox -v 0 /etc/kannel/sms.conf >>> [...] >>> 2009-09-05 16:34:33 [2854] [6] DEBUG: AT2[/dev/ttyS0]: device opened >>> 2009-09-05 16:34:33 [2854] [6] INFO: AT2[/dev/ttyS0]: init device >>> 2009-09-05 16:34:33 [2854] [6] INFO: AT2[/dev/ttyS0]: speed set to 9600 >>> 2009-09-05 16:34:33 [2854] [6] DEBUG: AT2[/dev/ttyS0]: --> ATZ^M >>> 2009-09-05 16:34:37 [2854] [6] ERROR: AT2[/dev/ttyS0]: Wrong or no >>> answer >>> to >>> ATZ, ignoring >>> 2009-09-05 16:34:37 [2854] [6] DEBUG: AT2[/dev/ttyS0]: --> AT^M >>> 2009-09-05 16:34:41 [2854] [6] ERROR: AT2[/dev/ttyS0]: Wrong or no >>> answer >>> to >>> AT. Trying again >>> 2009-09-05 16:34:41 [2854] [6] DEBUG: AT2[/dev/ttyS0]: --> AT^M >>> 2009-09-05 16:34:45 [2854] [6] ERROR: AT2[/dev/ttyS0]: Second attempt to >>> send AT failed >>> 2009-09-05 16:34:45 [2854] [6] ERROR: AT2[/dev/ttyS0]: Opening failed. >>> Terminating >>> 2009-09-05 16:34:45 [2854] [6] INFO: AT2[/dev/ttyS0]: closing device >>> [...] >>> >>> I don't no what to do.... >>> Thanx a lot. >>> >>> >>> >>> Nikos Balkanas wrote: >>>> >>>> Hi, >>>> >>>> I don't know gnokii, and I am not interested in it. However, I do know >>>> wvdial, minicom and statserial all useful tools to diagnose serial >>>> problems. >>>> >>>> Are you sure your modem is at /dev/ttyS0? What does: >>>> >>>> dmesg | grep tty >>>> >>>> show? >>>> >>>> BR, >>>> Nikos >>>> ----- Original Message ----- >>>> From: "Juxener" <[email protected]> >>>> To: <[email protected]> >>>> Sent: Wednesday, August 19, 2009 9:05 PM >>>> Subject: Re: Send SMS with Siemens M20 on Linux >>>> >>>> >>>>> >>>>> Thanks for your answer Jovan, >>>>> >>>>> but in my /etc/kannel/sms.conf I've : >>>>> include = "/etc/kannel/modems.conf" >>>>> >>>>> And in my /etc/kannel/modems.conf I've : >>>>> group = modems >>>>> id = siemens_m20 >>>>> name = "Siemens M20" >>>>> detect-string = "SIEMENS" >>>>> detect-string2 = "M20" >>>>> speed = 19200 >>>>> enable-hwhs = "AT\\Q3" >>>>> keepalive-cmd = "AT+CBC;+CSQ" >>>>> need-sleep = true >>>>> >>>>> But that doesn't works... >>>>> >>>>> >>>>> >>>>> Jovan Kostovski-2 wrote: >>>>>> >>>>>> On Mon, Aug 17, 2009 at 12:01 AM, Juxener<[email protected]> wrote: >>>>>>> >>>>>>> Hello, >>>>>>> sorry for my english (I'm french). >>>>>>> >>>>>>> I'm trying to use an Siemens M20 modem >>>>>>> (http://www.coster.info/costerit/teleges/doc/gsm812s.pdf), to send a >>>>>>> text. >>>>>>> I'm on Linux. >>>>>> >>>>>> Check this list message: >>>>>> http://www.ultraviolet.org/mail-archives/kannel.2006/msg01164.html >>>>>> >>>>>> BR, Jovan >>>>>> >>>>>> >>>>>> >>>>> >>>>> -- >>>>> View this message in context: >>>>> http://www.nabble.com/Send-SMS-with-Siemens-M20-on-Linux-tp24941326p25049150.html >>>>> Sent from the Kannel - User mailing list archive at Nabble.com. >>>>> >>>>> >>>> >>>> >>>> >>>> >>> >>> -- >>> View this message in context: >>> http://www.nabble.com/Send-SMS-with-Siemens-M20-on-Linux-tp24941326p25308016.html >>> Sent from the Kannel - User mailing list archive at Nabble.com. >>> >>> >> >> >> >> > > -- View this message in context: http://www.nabble.com/Send-SMS-with-Siemens-M20-on-Linux-tp24941326p25318392.html Sent from the Kannel - User mailing list archive at Nabble.com.
