Hello all ... I did it all you told me but I'm having the same problem yet.
I used the command wvdialconf /etc/wvdial.conf for be sure if the modem is on /dev/ttyS0 and I got the fallow: **** Editing `/etc/wvdial.conf'. Scanning your serial ports for a modem. ttyS0<Info>: Device or resource busy Modem Port Scan<*1>: S0 ttyS1<Info>: Device or resource busy Modem Port Scan<*1>: S1 ttyS2<Info>: Device or resource busy Modem Port Scan<*1>: S2 ttyS3<Info>: Device or resource busy Modem Port Scan<*1>: S3 Sorry, no modem was detected! Is it in use by another program? Did you configure it properly with setserial? Please read the FAQ at http://open.nit.ca/wiki/?WvDial If you still have problems, send mail to <[email protected]>. ***** But using gnome-ppp it detected the modem, it's the output: ******** GNOME PPP: STDOUT: Scanning your serial ports for a modem. GNOME PPP: STDOUT: GNOME PPP: STDERR: ttyS0<*1>: ATQ0 V1 E1 -- ��U��W� GNOME PPP: STDERR: ttyS0<*1>: failed with 9600 baud, next try: 115200 baud GNOME PPP: STDERR: ttyS0<*1>: ATQ0 V1 E1 -- OK GNOME PPP: STDERR: ttyS0<*1>: ATQ0 V1 E1 Z -- OK GNOME PPP: STDERR: ttyS0<*1>: ATQ0 V1 E1 S0=0 -- OK GNOME PPP: STDERR: ttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK GNOME PPP: STDERR: ttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK GNOME PPP: STDERR: ttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK GNOME PPP: STDERR: ttyS0<*1>: Modem Identifier: ATI -- WAVECOM WIRELESS CPU GNOME PPP: STDERR: ttyS0<*1>: Max speed is 115200; that should be safe. GNOME PPP: STDERR: ttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK GNOME PPP: STDERR: ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud GNOME PPP: STDERR: ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud GNOME PPP: STDERR: ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. GNOME PPP: STDOUT: GNOME PPP: STDERR: Modem Port Scan<*1>: S2 S3 GNOME PPP: STDOUT: Found a modem on /dev/ttyS0. GNOME PPP: STDOUT: Modem configuration written to /dev/null. GNOME PPP: STDERR: ttyS0<Info>: Speed 115200; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0" ********************** So I think that the problem could be a PIN code, maybe I have to set it, please check the error: ********************* 009-10-07 09:58:03 [3180] [6] DEBUG: AT2[mSmsc]: detecting modem speed. 2009-10-07 09:58:03 [3180] [6] INFO: AT2[mSmsc]: opening device 2009-10-07 09:58:03 [3180] [6] DEBUG: AT2[mSmsc]: device opened. Telnet mode = 0 2009-10-07 09:58:03 [3180] [5] DEBUG: Thread 5 (gw/bb_boxc.c:smsboxc_run) maps to pid 3180. 2009-10-07 09:58:03 [3180] [0] DEBUG: Started thread 6 (gw/smsc/smsc_at.c:at2_device_thread) 2009-10-07 09:58:03 [3180] [0] DEBUG: Started thread 7 (gw/bb_smscconn.c:sms_router) 2009-10-07 09:58:03 [3180] [0] INFO: ---------------------------------------- 2009-10-07 09:58:03 [3180] [0] INFO: Kannel bearerbox II version starting 2009-10-07 09:58:03 [3180] [0] INFO: MAIN: Start-up done, entering mainloop 2009-10-07 09:58:03 [3180] [0] DEBUG: AT2[mSmsc]: start called 2009-10-07 09:58:03 [3180] [7] DEBUG: Thread 7 (gw/bb_smscconn.c:sms_router) maps to pid 3180. 2009-10-07 09:58:04 [3180] [6] DEBUG: AT2[mSmsc]: device opened 2009-10-07 09:58:04 [3180] [6] INFO: AT2[mSmsc]: speed set to 115200 2009-10-07 09:58:04 [3180] [6] DEBUG: AT2[mSmsc]: --> ^M 2009-10-07 09:58:06 [3180] [6] DEBUG: AT2[mSmsc]: --> AT^M 2009-10-07 09:58:06 [3180] [6] DEBUG: AT2[mSmsc]: <-- OK 2009-10-07 09:58:06 [3180] [6] INFO: AT2[mSmsc]: Closing device 2009-10-07 09:58:06 [3180] [6] INFO: AT2[mSmsc]: detect speed is 115200 2009-10-07 09:58:06 [3180] [6] DEBUG: AT2[mSmsc]: detecting modem type 2009-10-07 09:58:06 [3180] [6] INFO: AT2[mSmsc]: opening device 2009-10-07 09:58:06 [3180] [6] DEBUG: AT2[mSmsc]: device opened. Telnet mode = 0 2009-10-07 09:58:07 [3180] [6] DEBUG: AT2[mSmsc]: device opened 2009-10-07 09:58:07 [3180] [6] INFO: AT2[mSmsc]: speed set to 115200 2009-10-07 09:58:07 [3180] [6] DEBUG: AT2[mSmsc]: --> ^M 2009-10-07 09:58:09 [3180] [6] DEBUG: AT2[mSmsc]: --> AT^M 2009-10-07 09:58:09 [3180] [6] DEBUG: AT2[mSmsc]: <-- OK 2009-10-07 09:58:09 [3180] [6] DEBUG: AT2[mSmsc]: --> AT&F^M 2009-10-07 09:58:09 [3180] [6] DEBUG: AT2[mSmsc]: <-- OK 2009-10-07 09:58:09 [3180] [6] DEBUG: AT2[mSmsc]: --> ATE0^M 2009-10-07 09:58:09 [3180] [6] DEBUG: AT2[mSmsc]: <-- OK 2009-10-07 09:58:09 [3180] [6] DEBUG: AT2[mSmsc]: --> ATI^M 2009-10-07 09:58:09 [3180] [6] DEBUG: AT2[mSmsc]: <-- WAVECOM WIRELESS CPU 2009-10-07 09:58:09 [3180] [6] DEBUG: AT2[mSmsc]: <-- MULTIBAND G850 1900 2009-10-07 09:58:09 [3180] [6] DEBUG: AT2[mSmsc]: <-- OK 2009-10-07 09:58:09 [3180] [6] DEBUG: AT2[mSmsc]: found string <WAVECOM>, using modem definition <WAVECOM> 2009-10-07 09:58:09 [3180] [6] DEBUG: AT2[mSmsc]: --> AT+CSMS=?^M 2009-10-07 09:58:09 [3180] [6] DEBUG: AT2[mSmsc]: <-- ERROR 2009-10-07 09:58:09 [3180] [6] ERROR: AT2[mSmsc]: Generic error: ERROR 2009-10-07 09:58:09 [3180] [6] INFO: AT2[mSmsc]: Closing device 2009-10-07 09:58:09 [3180] [6] INFO: AT2[mSmsc]: opening device 2009-10-07 09:58:09 [3180] [6] DEBUG: AT2[mSmsc]: device opened. Telnet mode = 0 2009-10-07 09:58:09 [3180] [6] DEBUG: AT2[mSmsc]: device opened 2009-10-07 09:58:09 [3180] [6] INFO: AT2[mSmsc]: Logging in 2009-10-07 09:58:10 [3180] [6] INFO: AT2[mSmsc]: init device 2009-10-07 09:58:10 [3180] [6] INFO: AT2[mSmsc]: speed set to 115200 2009-10-07 09:58:10 [3180] [6] DEBUG: AT2[mSmsc]: --> ATZ^M 2009-10-07 09:58:10 [3180] [6] DEBUG: AT2[mSmsc]: <-- OK 2009-10-07 09:58:10 [3180] [6] DEBUG: AT2[mSmsc]: --> AT^M 2009-10-07 09:58:10 [3180] [6] DEBUG: AT2[mSmsc]: <-- AT 2009-10-07 09:58:10 [3180] [6] DEBUG: AT2[mSmsc]: <-- OK 2009-10-07 09:58:10 [3180] [6] DEBUG: AT2[mSmsc]: --> AT&F^M 2009-10-07 09:58:10 [3180] [6] DEBUG: AT2[mSmsc]: <-- AT&F 2009-10-07 09:58:10 [3180] [6] DEBUG: AT2[mSmsc]: <-- OK 2009-10-07 09:58:10 [3180] [6] DEBUG: AT2[mSmsc]: --> ATE0^M 2009-10-07 09:58:10 [3180] [6] DEBUG: AT2[mSmsc]: <-- ATE0 2009-10-07 09:58:10 [3180] [6] DEBUG: AT2[mSmsc]: <-- OK 2009-10-07 09:58:10 [3180] [6] DEBUG: AT2[mSmsc]: --> AT+IFC=2,2^M 2009-10-07 09:58:10 [3180] [6] DEBUG: AT2[mSmsc]: <-- OK 2009-10-07 09:58:10 [3180] [6] DEBUG: AT2[mSmsc]: --> AT+CPIN?^M 2009-10-07 09:58:10 [3180] [6] DEBUG: AT2[mSmsc]: <-- ERROR 2009-10-07 09:58:10 [3180] [6] ERROR: AT2[mSmsc]: Generic error: ERROR 2009-10-07 09:58:10 [3180] [6] ERROR: AT2[mSmsc]: Initialization of device failed. 2009-10-07 09:58:10 [3180] [6] INFO: AT2[mSmsc]: Closing device 2009-10-07 09:58:10 [3180] [6] ERROR: AT2[mSmsc]: Couldn't connect (retrying in 10 seconds). ************************ Additionally, you need to be sure your modem is on /dev/ttyS0 . If you are using Linux, run > > # wvdialconf /etc/wvdial.conf > > This will do a scan and give you a visual display of the > available modem and 'location'. On Wed, 2009-10-07 at 10:10 -0400, Elvis Jorge wrote: > > ----- Original Message ----- > From: Nikos Balkanas > To: [email protected] ; [email protected] > Cc: [email protected] > Sent: Wednesday, October 07, 2009 12:44 AM > Subject: Re: problem with GSM Modem > > > Hi, > > Just a note to avoid confusion. In the cvs modems.conf id, wavecom is > in lower case: > > group = modems > id = wavecom > name = Wavecom > detect-string = "WAVECOM" > > Therefore if working with that, modemtype in group smsc should also > be: > > modemtype = wavecom > > as well. > > BR, > Nikos > ----- Original Message ----- > From: Kenny Orisanaiye > To: [email protected] > Cc: [email protected] > Sent: Wednesday, October 07, 2009 1:08 AM > Subject: Re: problem with GSM Modem > > > Hi Elvis, > > I also use Wavecom Fastrack Supreme and after much trial and > errors with the setting i discoved that the default settings > works just fine for us. Below is an extract from our config. > > ######################## > group = modems > id = WAVECOM > name = "WAVECOM" > detect-string = "WAVECOM" > ######################## > > ######################## > group = smsc > smsc = at > smsc-id = mSmsc > modemtype = WAVECOM > device = /dev/ttyS0 > my-number = ************ > connect-allow-ip = ****** > log-level = 0 > ######################## > > Additionally, you need to be sure your modem is > on /dev/ttyS0 . If you are using Linux, run > > # wvdialconf /etc/wvdial.conf > > This will do a scan and give you a visual display of the > available modem and 'location'. > > > -- > Kenny > > e: [email protected] > w: www.nuObjects.com > > Bulk SMS Solutions | Managed Hosting | Enterprise Application > Development > > > On Tue, Oct 6, 2009 at 2:50 PM, Elvis Manuel Jorge > <[email protected]> wrote: > I did that you told me Alejandro but It didn't work > I'm having the same > error, somebody that has worked with Wavecom modem > help me. > > Thanks > > > On Mon, 2009-10-05 at 23:10 +0200, Alejandro Guerrieri > wrote: > > Try changing "wavecom" for "WAVECOM" on the > detect-string. > > > > > > Regards, > > > > > > Alex > > > > On Mon, Oct 5, 2009 at 10:58 PM, Elvis Manuel Jorge > > <[email protected]> wrote: > > Hello all... > > > > I had configured kannel to use my cellphone > (Sony Ericsson > > P1i) as > > modem, but know I bought a Wavecom Fastrack > Supreme 20 modem > > and I've > > couldn't configure correctly, here they are > the errors and my > > configuration file. Please I need you to > help me. > > > > 2009-10-05 16:49:18 [3143] [6] DEBUG: > AT2[gsm]: --> ATI^M > > 2009-10-05 16:49:18 [3143] [6] DEBUG: > AT2[gsm]: <-- WAVECOM > > WIRELESS CPU > > 2009-10-05 16:49:18 [3143] [6] DEBUG: > AT2[gsm]: <-- MULTIBAND > > G850 > > 1900 > > 2009-10-05 16:49:18 [3143] [6] DEBUG: > AT2[gsm]: <-- OK > > 2009-10-05 16:49:18 [3143] [6] DEBUG: > AT2[gsm]: Cannot detect > > modem, > > using generic > > 2009-10-05 16:49:18 [3143] [6] DEBUG: > AT2[gsm]: Reading modem > > definitions from <smskannel2.conf> > > 2009-10-05 16:49:18 [3143] [6] DEBUG: > AT2[gsm]: Found <1> > > modems in > > config > > 2009-10-05 16:49:18 [3143] [6] PANIC: > AT2[gsm]: Cannot detect > > modem and > > generic not found > > 2009-10-05 16:49:18 [3143] [6] > PANIC: ./bearerbox(gw_panic > > +0xc2) > > [0x80cbf72] > > 2009-10-05 16:49:18 [3143] [6] > PANIC: ./bearerbox [0x806ca22] > > 2009-10-05 16:49:18 [3143] [6] > PANIC: ./bearerbox [0x806d5b1] > > 2009-10-05 16:49:18 [3143] [6] > PANIC: ./bearerbox [0x80c2831] > > 2009-10-05 16:49:18 [3143] [6] > PANIC: /lib/libpthread.so.0 > > [0x72b50b] > > 2009-10-05 16:49:18 [3143] [6] > PANIC: /lib/libc.so.6(clone > > +0x5e) > > [0x66cb2e] > > > > group = core > > admin-port = 13000 > > smsbox-port = 13001 > > admin-password = bar > > admin-allow-ip = "*.*.*.*" > > log-file = "/var/log/kannel/kannel.log" > > log-level = 0 > > access-log = "/var/log/kannel/access.log" > > > > group = modems > > id = wavecom > > name = "wavecom" > > detect-string = "wavecom" > > init-string = "ATZ" > > init-string = "ATQ0 V1 E1 S0=0 &C1 &D2 > +FCLASS=0" > > > > group = smsc > > smsc = at > > modemtype = auto > > smsc-id = gsm > > device = /dev/ttyS0 > > my-number = +18298666697 > > sms-center = +18098599999 > > log-level = 0 > > > > group = sendsms-user > > username = tester > > password = foobar > > user-allow-ip = "*.*.*.*" > > > > group = sms-service > > keyword = nop > > text = "You asked nothing and I did it!" > > > > group = sms-service > > keyword = default > > catch-all = yes > > accept-x-kannel-headers = true > > assume-plain-text = true > > text = "No service specified" > > -- INSERT -- > >
