It's working now :-) Thanks a lot all!
Alex P.S. I haven't tried installing it on my SATA disk because I have there a Local Node already running but I'm going to try again on another one to see if I can send to you the error log. 2012/10/8 Mike Burns <[email protected]> > On Mon, 2012-10-08 at 09:54 +0100, Alexandre Santos wrote: > > > > > > 2012/10/8 Fabian Deutsch <[email protected]> > > Am Montag, den 08.10.2012, 09:24 +0100 schrieb Alexandre > > Santos: > > > 2012/10/8 Fabian Deutsch <[email protected]> > > > Hey, > > > > > > Am Sonntag, den 07.10.2012, 15:29 +0100 schrieb > > Alexandre > > > Santos: > > > > Hi, > > > > I'm trying to install the ovirt-node iso image on > > a SATA > > > disk and when > > > > it gets to the screen where it shows 25% completed > > the > > > kernel hangs. I > > > > can't connect using a serial console to see what > > has > > > happened. If I > > > > reboot using a usb linux disk I see that the SATA > > disk has > > > been > > > > formated and the partitions that existed before > > disappeared, > > > being > > > > there just one partition of type "ee" > > > > > > > > > Is there any error displayed when kernel hangs at > > 25%? And it > > > can take > > > some time to pass the 25% (up to ~2min or so). > > > > > > No, I think it's a kernel hang because the lights on the > > keyboard halt > > > and I can't change to tty2, etc.. I even changed to tty2 and > > waited to > > > see if there were some errors but nothing. I've read that > > "tty8" was > > > the logging console but no luck also. > > > BTW, I tried with an IDE disk and the result was the same. > > > > > > Mh, okay. > > Could you try booting without the rhgb and quiet kernel > > arguments. I > > hope that some errors will be displayed on the screen so we > > get an idea > > about the problem. > > > > > > > > > If I use a 8 GB usb pen-drive instead of the SATA > > disk, the > > > > installation comes to an end and I reboot but then > > I get > > > some error > > > > about not getting /dev/mapper/by-name/Root and the > > boot > > > fails to a > > > > dracut shell. > > > > Any ideas? > > > > > > > > > In the dracut shell, could you run blkid and post > > the results? > > > > > > I noticed that the USB Disk was named RootBackup instead of > > Root... I > > > then rebooted and chose uninstall and then installed oVirt > > Node from > > > scratch and now it worked. > > Glad it worked the second time. There should be 4 partitions on the > disk. > > Partition 1 is for UEFI or bios_boot depending on your machine type. > Partition 2 and Partition 3 are Root and RootBackup. So seeing a > RootBackup is correct. Not seeing a Root is incorrect. If you rebooted > the host in the middle of the install, or if the install hung for some > reason, I can see that situation happening and see it working after > uninstall/install. > > > > I can't activate Networking because I have that "no > > hostname" error > > > mentioned in another post. I think it's related to that... > > You can't activate networking at all? That is news to me. The node > should work perfectly fine with or without a FQDN. > > > > > > > Yes, I've also seen the hostname error. And I've also seen > > some problems > > with the rootfs lately. > > Have you seen these issues with the 2.5.2 build? Or only master branch > builds? > > > Could you provide a screenshot/dump of the console with that > > error? > > > > - fabian > > > > > > Ok! I'll send them as soon as possible. > > > > Alex > > > > > > _______________________________________________ > > Users mailing list > > [email protected] > > http://lists.ovirt.org/mailman/listinfo/users > > >
_______________________________________________ Users mailing list [email protected] http://lists.ovirt.org/mailman/listinfo/users
