On Thu, 2012-10-11 at 11:12 +0100, Alexandre Santos wrote: > Hi, > yesterday I tried the new oVirt Node 2.5.3. I tried installing it > without the quiet flag but no luck. It hanged again and the kernel > didn't show any error on console (tty2). > Later will test without the rhgh flag.
Default options? TUI install? Hardware? UEFI or legacy bios? > > Alex > > BTW, now the hostname works on 2.5.3 :-) The network configuration is > still tricky... sometimes I have an "Apply" sometimes only a "Back" > choice. I *think* this is a feature of being registered to ovirt-engine. Once you are registered, you can't change the network through the TUI anymore. If you're not registered with Engine, please elaborate a bit and I'll try to figure out what is going on. Mike > > 2012/10/9 Alexandre Santos <[email protected]> > It's working now :-) > > Thanks a lot all! > > Alex > > P.S. I haven't tried installing it on my SATA disk because I > have there a Local Node already running but I'm going to try > again on another one to see if I can send to you the error > log. > > > 2012/10/8 Mike Burns <[email protected]> > On Mon, 2012-10-08 at 09:54 +0100, Alexandre Santos > wrote: > > > > > > 2012/10/8 Fabian Deutsch <[email protected]> > > Am Montag, den 08.10.2012, 09:24 +0100 > schrieb Alexandre > > Santos: > > > 2012/10/8 Fabian Deutsch > <[email protected]> > > > Hey, > > > > > > Am Sonntag, den 07.10.2012, 15:29 > +0100 schrieb > > Alexandre > > > Santos: > > > > Hi, > > > > I'm trying to install the > ovirt-node iso image on > > a SATA > > > disk and when > > > > it gets to the screen where it > shows 25% completed > > the > > > kernel hangs. I > > > > can't connect using a serial > console to see what > > has > > > happened. If I > > > > reboot using a usb linux disk I > see that the SATA > > disk has > > > been > > > > formated and the partitions that > existed before > > disappeared, > > > being > > > > there just one partition of type > "ee" > > > > > > > > > Is there any error displayed when > kernel hangs at > > 25%? And it > > > can take > > > some time to pass the 25% (up to > ~2min or so). > > > > > > No, I think it's a kernel hang because the > lights on the > > keyboard halt > > > and I can't change to tty2, etc.. I even > changed to tty2 and > > waited to > > > see if there were some errors but nothing. > I've read that > > "tty8" was > > > the logging console but no luck also. > > > BTW, I tried with an IDE disk and the > result was the same. > > > > > > Mh, okay. > > Could you try booting without the rhgb and > quiet kernel > > arguments. I > > hope that some errors will be displayed on > the screen so we > > get an idea > > about the problem. > > > > > > > > > If I use a 8 GB usb pen-drive > instead of the SATA > > disk, the > > > > installation comes to an end and > I reboot but then > > I get > > > some error > > > > about not > getting /dev/mapper/by-name/Root and the > > boot > > > fails to a > > > > dracut shell. > > > > Any ideas? > > > > > > > > > In the dracut shell, could you run > blkid and post > > the results? > > > > > > I noticed that the USB Disk was named > RootBackup instead of > > Root... I > > > then rebooted and chose uninstall and then > installed oVirt > > Node from > > > scratch and now it worked. > > > Glad it worked the second time. There should be 4 > partitions on the > disk. > > Partition 1 is for UEFI or bios_boot depending on your > machine type. > Partition 2 and Partition 3 are Root and RootBackup. > So seeing a > RootBackup is correct. Not seeing a Root is > incorrect. If you rebooted > the host in the middle of the install, or if the > install hung for some > reason, I can see that situation happening and see it > working after > uninstall/install. > > > > I can't activate Networking because I have > that "no > > hostname" error > > > mentioned in another post. I think it's > related to that... > > > You can't activate networking at all? That is news to > me. The node > should work perfectly fine with or without a FQDN. > > > > > > > > Yes, I've also seen the hostname error. And > I've also seen > > some problems > > with the rootfs lately. > > > Have you seen these issues with the 2.5.2 build? Or > only master branch > builds? > > > Could you provide a screenshot/dump of the > console with that > > error? > > > > - fabian > > > > > > Ok! I'll send them as soon as possible. > > > > Alex > > > > > > > _______________________________________________ > > Users mailing list > > [email protected] > > http://lists.ovirt.org/mailman/listinfo/users > > > > > > _______________________________________________ > Users mailing list > [email protected] > http://lists.ovirt.org/mailman/listinfo/users _______________________________________________ Users mailing list [email protected] http://lists.ovirt.org/mailman/listinfo/users
