2012/10/11 Alexandre Santos <santosa...@gmail.com> > 2012/10/11 Mike Burns <mbu...@redhat.com> > >> On Thu, 2012-10-11 at 11:12 +0100, Alexandre Santos wrote: >> > Hi, >> > yesterday I tried the new oVirt Node 2.5.3. I tried installing it >> > without the quiet flag but no luck. It hanged again and the kernel >> > didn't show any error on console (tty2). >> > Later will test without the rhgh flag. >> >> Default options? TUI install? Hardware? UEFI or legacy bios? >> > > I always choose the troubleshooting option and then do an install with > basic video. The only thing I changed from the default kernel boot line was > the quiet flag. > > Yes, TUI. > > Hardware: this is an old MSI P35Neo MB with 4 GB RAM and a Xeon 3040. The > SATA disk is connected to the onboard controller. The same problem occurred > with an IDE HDD. >
Without rhgb and quiet no luck at all. Tomorrow will try with a SATA PCI Card with a Sil chip. > > >> >> > >> > Alex >> > >> > BTW, now the hostname works on 2.5.3 :-) The network configuration is >> > still tricky... sometimes I have an "Apply" sometimes only a "Back" >> > choice. >> >> I *think* this is a feature of being registered to ovirt-engine. Once >> you are registered, you can't change the network through the TUI >> anymore. >> >> If you're not registered with Engine, please elaborate a bit and I'll >> try to figure out what is going on. >> > > What you're saying makes sense. The problem I had was that my node was > booting with DHCP and the IP changed. When I got to the engine / web > administrator, my Host was not detected and I couldn't change it's IP, only > the hostname... On the TUI I can't change the IP because I'm registered but > can't change it also on the engine. Is this correct? > >> >> Mike >> >> > >> > 2012/10/9 Alexandre Santos <santosa...@gmail.com> >> > It's working now :-) >> > >> > Thanks a lot all! >> > >> > Alex >> > >> > P.S. I haven't tried installing it on my SATA disk because I >> > have there a Local Node already running but I'm going to try >> > again on another one to see if I can send to you the error >> > log. >> > >> > >> > 2012/10/8 Mike Burns <mbu...@redhat.com> >> > On Mon, 2012-10-08 at 09:54 +0100, Alexandre Santos >> > wrote: >> > > >> > > >> > > 2012/10/8 Fabian Deutsch <fabi...@redhat.com> >> > > Am Montag, den 08.10.2012, 09:24 +0100 >> > schrieb Alexandre >> > > Santos: >> > > > 2012/10/8 Fabian Deutsch >> > <fabi...@redhat.com> >> > > > Hey, >> > > > >> > > > Am Sonntag, den 07.10.2012, 15:29 >> > +0100 schrieb >> > > Alexandre >> > > > Santos: >> > > > > Hi, >> > > > > I'm trying to install the >> > ovirt-node iso image on >> > > a SATA >> > > > disk and when >> > > > > it gets to the screen where it >> > shows 25% completed >> > > the >> > > > kernel hangs. I >> > > > > can't connect using a serial >> > console to see what >> > > has >> > > > happened. If I >> > > > > reboot using a usb linux disk I >> > see that the SATA >> > > disk has >> > > > been >> > > > > formated and the partitions that >> > existed before >> > > disappeared, >> > > > being >> > > > > there just one partition of type >> > "ee" >> > > > >> > > > >> > > > Is there any error displayed when >> > kernel hangs at >> > > 25%? And it >> > > > can take >> > > > some time to pass the 25% (up to >> > ~2min or so). >> > > > >> > > > No, I think it's a kernel hang because the >> > lights on the >> > > keyboard halt >> > > > and I can't change to tty2, etc.. I even >> > changed to tty2 and >> > > waited to >> > > > see if there were some errors but nothing. >> > I've read that >> > > "tty8" was >> > > > the logging console but no luck also. >> > > > BTW, I tried with an IDE disk and the >> > result was the same. >> > > >> > > >> > > Mh, okay. >> > > Could you try booting without the rhgb and >> > quiet kernel >> > > arguments. I >> > > hope that some errors will be displayed on >> > the screen so we >> > > get an idea >> > > about the problem. >> > > >> > > > >> > > > > If I use a 8 GB usb pen-drive >> > instead of the SATA >> > > disk, the >> > > > > installation comes to an end and >> > I reboot but then >> > > I get >> > > > some error >> > > > > about not >> > getting /dev/mapper/by-name/Root and the >> > > boot >> > > > fails to a >> > > > > dracut shell. >> > > > > Any ideas? >> > > > >> > > > >> > > > In the dracut shell, could you run >> > blkid and post >> > > the results? >> > > > >> > > > I noticed that the USB Disk was named >> > RootBackup instead of >> > > Root... I >> > > > then rebooted and chose uninstall and then >> > installed oVirt >> > > Node from >> > > > scratch and now it worked. >> > >> > >> > Glad it worked the second time. There should be 4 >> > partitions on the >> > disk. >> > >> > Partition 1 is for UEFI or bios_boot depending on your >> > machine type. >> > Partition 2 and Partition 3 are Root and RootBackup. >> > So seeing a >> > RootBackup is correct. Not seeing a Root is >> > incorrect. If you rebooted >> > the host in the middle of the install, or if the >> > install hung for some >> > reason, I can see that situation happening and see it >> > working after >> > uninstall/install. >> > >> > > > I can't activate Networking because I have >> > that "no >> > > hostname" error >> > > > mentioned in another post. I think it's >> > related to that... >> > >> > >> > You can't activate networking at all? That is news to >> > me. The node >> > should work perfectly fine with or without a FQDN. >> > >> > >> > > >> > > >> > > Yes, I've also seen the hostname error. And >> > I've also seen >> > > some problems >> > > with the rootfs lately. >> > >> > >> > Have you seen these issues with the 2.5.2 build? Or >> > only master branch >> > builds? >> > >> > > Could you provide a screenshot/dump of the >> > console with that >> > > error? >> > > >> > > - fabian >> > > >> > > >> > > Ok! I'll send them as soon as possible. >> > > >> > > Alex >> > > >> > > >> > >> > > _______________________________________________ >> > > Users mailing list >> > > Users@ovirt.org >> > > http://lists.ovirt.org/mailman/listinfo/users >> > >> > >> > >> > >> > >> > _______________________________________________ >> > Users mailing list >> > Users@ovirt.org >> > http://lists.ovirt.org/mailman/listinfo/users >> >> >> >
_______________________________________________ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users