I have enabled the VLAN tagging but no dice. Still I cannot attach
logical network to the VLANS in oVirt, and I see them represented in the
list, like this:
name bond vlan Network name address
eth0 bond0.50 ovirtmgmt
bond0
eth1 bond0.60
ovirtmgmt
-------------------------------------------------------------
Also since ip address is added to a ovirtmgmt bridge, I can not save any
additional configuration until I resolve this because it ovirt says that
there are two interfaces with the same IP address.
System-Email
Mit freundlichen Grüßen / Best Regards
Bojan Popovic
System Administrator | IT Novi Sad
Tel: +49 (0) 711/ 320 90 285
www.jago24.de <http://www.jago24.de>
www.jago-ag.de <http://www.jago-ag.de>
E-Mail: bojan.popo...@jago-ag.de <mailto:bojan.popo...@jago-ag.de>
<http://www.jago24.de>
JAGO AG
Amtsgericht Stuttgart
Ingersheimer Str.12
Reg.Nr.: HRB 741306
D-70499 Stuttgart
USt-ID: DE283513307
Vorstand:
WEEE-Reg.-Nr. DE 70299572
Goran Jakovac
Aufsichtsratsvorsitzender:
Dipl.-oec. Univ. Rolf Breyer
Jago_AG_logo
On 30.03.2015. 13:14, René Koch wrote:
>
> Hi Bojan,
>
>
>
> Did you configure a VLAN tag für your ovirtmgmt interface?
>
> You have to do this in „Data Centers“ – select dc – „Logical Networks“.
>
> Afterwards you should be able to configure network from oVirt webadmin
> interface again.
>
> Don’t have a test setup with VLAN tags for ovirtmgmt atm, but did this
> multiple times before…
>
>
>
>
> Regards,
>
> René
>
>
>
>
>
> *Von:*users-boun...@ovirt.org [mailto:users-boun...@ovirt.org] *Im
> Auftrag von *Bojan Popovic
> *Gesendet:* Montag, 30. März 2015 12:15
> *An:* users@ovirt.org
> *Betreff:* [ovirt-users] oVirt management network
>
>
>
> Hello, I am having a strange issue in creating ovirtmgmt bridge over
> vlan interface.
>
> I have set-up a bond from physical interfaces. On top of a bond there
> are three VLANs one of which is in ovirtmgmt bridge. I have set it up
> manually according to http://www.ovirt.org/Bonding_VLAN_Bridge
>
> Somehow the bond itself is also added to bridge in oVirt web
> interface, after reboot there also were two added lines to
> configuration of that bond:
> # Generated by VDSM version 4.16.10-8.gitc937927.el7
> BRIDGE=ovirtmgmt
>
> No matter how I try to remove the bond from the bridge it doesn't
> succeed. If I edit the config files manually it isn't replicated to
> web interface. If I try to detach it from web interface, I can only
> attach bridge back to the bond interface. Of course configuration
> cannot be saved until the bridge is attached to an interface.
>
> I have tried putting the host in maintenance mode, shutting down the
> hosted engine and doing all the changes live.
>
> Anyone has a suggestion how to resolve this?
>
> Thanks.
>
>
>
>
>
>
>
_______________________________________________
Users mailing list
Users@ovirt.org
http://lists.ovirt.org/mailman/listinfo/users
