I found some settings that work: S5.0E 11700 V 9750 t v W15 [E0 10 38 F0] W100 [E0 10 38 F0] W100 [E0 11 00] W100 A W15 t S5.0E 99999 V 10600 t v W15 [E0 10 38 F1] W100 [E0 10 38 F1] W100 [E0 11 00] W100 A W15 T S5.0E 11700 H 9750 t V W15 [E0 10 38 F2] W100 [E0 10 38 F2] W100 [E0 11 00] W100 A W15 t S5.0E 99999 H 10600 t V W15 [E0 10 38 F3] W100 [E0 10 38 F3] W100 [E0 11 00] W100 A W15 T
S13.0E 11700 V 9750 t v W15 [E0 10 38 F4] W100 [E0 10 38 F4] W100 [E0 11 00] W100 B W15 t S13.0E 99999 V 10600 t v W15 [E0 10 38 F5] W100 [E0 10 38 F5] W100 [E0 11 00] W100 B W15 T S13.0E 11700 H 9750 t V W15 [E0 10 38 F6] W100 [E0 10 38 F6] W100 [E0 11 00] W100 B W15 t S13.0E 99999 H 10600 t V W15 [E0 10 38 F7] W100 [E0 10 38 F7] W100 [E0 11 00] W100 B W15 T S16.0E 11700 V 9750 t v W15 [E0 10 38 F8] W100 [E0 10 38 F8] W100 [E0 11 00] W100 A W15 t S16.0E 99999 V 10600 t v W15 [E0 10 38 F9] W100 [E0 10 38 F9] W100 [E0 11 00] W100 A W15 T S16.0E 11700 H 9750 t V W15 [E0 10 38 FA] W100 [E0 10 38 FA] W100 [E0 11 00] W100 A W15 t S16.0E 99999 H 10600 t V W15 [E0 10 38 FB] W100 [E0 10 38 FB] W100 [E0 11 00] W100 A W15 T S19.2E 11700 V 9750 t v W15 [E0 10 38 FC] W100 [E0 10 38 FC] W100 [E0 11 00] W100 B W15 t S19.2E 99999 V 10600 t v W15 [E0 10 38 FD] W100 [E0 10 38 FD] W100 [E0 11 00] W100 B W15 T S19.2E 11700 H 9750 t V W15 [E0 10 38 FE] W100 [E0 10 38 FE] W100 [E0 11 00] W100 B W15 t S19.2E 99999 H 10600 t V W15 [E0 10 38 FF] W100 [E0 10 38 FF] W100 [E0 11 00] W100 B W15 T They are in the order of ports on switch. A non proved explanation is that the LNB needs 100ms to powerup until it can work. Regards, Ilariu On 1/29/07, Ilariu Raducan < [EMAIL PROTECTED]> wrote:
I'm using VDR4You distribution, and I don't want to install kaffeine on it. I want to keep it small ;) I need to check if vdr is sending something that is not suposed to. Note that vdr works for channels on LNB1 if you disable diseqc in the setup. Ilariu On 1/29/07, Gregoire Favre < [EMAIL PROTECTED]> wrote: > > On Mon, Jan 29, 2007 at 01:32:16PM +0000, Ilariu Raducan wrote: > > I also have problems with 4 quad LNBs on a diseqc switch (1.0 and > another > > 2.0) > > If I plug out the cable from the card and plug it back again (reset > switch > > and LNBs) > > I can use szap to change the channels. I believe the quad LNBs have > diseqc > > switch > > inside and at reset they are in backward compatible mode > (Tone/Voltage). > > In Diseqc specifications/recommendations they recommend the diseqc LNB > > > should ignore responding > > to Tone/Voltage commands when they receive one diseqc command. > > Unfortunately, I did not find the proper diseqc commands for the LNBs. > > > > I will try today a workaround to reset the LNB before sending the > > diseqc.conf sequence in backward compatible mode: > > - switch to another LNB (hope the power will be cut for the one I need > for > > the channel) > > - do the sequence for current channel > > t v [E0 10 38 FF] W500 (switch to LNB4 and wait 500) [E0 10 38 F0] > W100 A > > W15 t (switch to LNB1, wait for power to stabilize, use back > compatible) > > > > If I am lucky enough the switch will cut the power for the LNB1 when I > > switch to LNB4. > > > > Does anybody knows the Diseqc commands for Quad LNBs?? > > Very stangely, under kaffeine here all runs perfectly ??? > Did you also try to use your quiete similar setup under kaffeine ? > > I have tried an hudge number of setup, including diseqc reset, resent of > messages... > > Maybe there is only two VDR user with quad lnb in the world using > diseqc ? > -- > Grégoire FAVRE http://gregoire.favre.googlepages.com http://www.gnupg.org > > _______________________________________________ > vdr mailing list > [email protected] > http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr >
_______________________________________________ vdr mailing list [email protected] http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr
