Hi Neal, Brent, Cokes, and Others who asked about FiRe 2, Neal's correct that earlier versions of FiRe 2 from January at the beginning of this year, up to the last version (released May 28, 2013), worked with VoiceOver. The FiRe 2 app got purchased by RØDE microphones, who will be taking over support for the app from Audiofile Engineering. They announced this on the RØDE microphones web site on July 2nd.
If you have an older version of the app that you can revert to, by deleting the latest version on your iOS device and using iTunes on your computer to sync this across to your device, you can still use the app. There's also a clunky way to get the audio back using the latest version, provided that you don't want to change the recording specs for bit rate on the configuration screen. It's based on being to navigate the controls of the screen by knowing where the control sequence is without audio feedback from VoiceOver, because you lose the VOiceOver audio when you double tap the "Recordings List Configure Input" button in the bottom left corner of the "Recordings" screen, and you don't get it back until you double tap the "Recordings List Add" button in the bottom right corner of the same "Recordings" screen. So, if you aren't changing the hardware configuration of recording setup or the recording bit rate, which is set to 44.1 KHz by default., do the following when you start a new recording: 1. Double tap the "Recordings List Add" button in the bottom right corner of the "Recordings" screen. This is where you lose audio from VoiceOver, because the app launches the configuration screen, as though you double tapped the "Recordings List Configure Input" button. However, focus will be on the "Cancel, back" button, so double tap to get out of the configuration screen. 2. You'll be taken back to the "Recordings" screen, still without VoiceOver audio. Do a four finger tap on the bottom half of the screen to move to the last element of the screen, which is the "Recordings List Add" button, and then double tap. 3. At this point you'll be in the screen for the recording you just added, and should be able to record normally. If you don't have the "Record" button, navigate to the "Settings" button at the bottom of the screen and double tap. Navigate to "Transport" and make sure that "Button Controls" switch under the Record button heading of the Transport screen is set to "on". Then navigate back to your recording and record as usual. Once you've done this, you can add recordings with the "Recordings List Add" button on the Recordings screen and make new recordings as long as the app is open without losing VoiceOver. But if you close the app, you'll have to go through this again to start your recordings. I haven't used additional stereo mic connections with FiRe. If you want to save those settings, I think that when you reach the configure screen, after about 5 or so seconds of checking for your hardware configuration, the app will add stereo channels to the end of the screen. Neal can probably tell you whether this is selected by default. If you want to save this setting, and it is selected by default, just flick twice to the right and double tap. You're moving from the default focus of the "Cancel" button at the top left of the configure screen, to the screen heading, and then to the "Save" button. Again, you'll be at the Recordings screen, and will want to pick up at step 2., where you do a four finger tap on the bottom half of the screen to move to the "Recordings List Add" button and double tap to get back your VoiceOver audio. Can people try this and check that it works for them? HTH. Cheers, Esther On 12 Jul 2013, at 08:24, Neal Ewers wrote: > Hi, previous versions did work. The last one totally crashed VoiceOver. I > have no clue what Rode will do with this. I will just have to wait and see. > > Neal > > > From: [email protected] [mailto:[email protected]] On Behalf Of > Brent Harding > Sent: Friday, July 12, 2013 11:44 AM > To: [email protected] > Subject: Re: Very interesting news about Fire 2 recorder > > I bought this thing awhile ago. Besides having to use the Focus 40 blue in > place of hearing audio from VO, is there a way to not have it turn the audio > all the way off when launching it? I suppose it's $6 down the drain, most > likely, but thought I'd ask. > > ----- Original Message ----- > From: Neal Ewers > To: [email protected] > Sent: Friday, July 12, 2013 11:33 AM > Subject: Very interesting news about Fire 2 recorder > > I just got this from the developer. > I had ask when the upade that would fix the voiceover problems would be out. > Their answer follows. > > > > “It will be available in RØDE Rec 2.8. As you might have heard, RØDE > Microphones acquired FiRe a couple of weeks ago. We imagine version 2.8 will > ship late August.” > > > Neal > -- -- You received this message because you are subscribed to the "VIPhone" Google Group. Post a new message to VIPhone by emailing [email protected]. Search and view the VIPhone archives by visiting http://www.mail-archive.com/[email protected]/. Reach the VIPhone owner and moderators by emailing [email protected]. Unsubscribe and leave VIPhone by emailing [email protected]. More VIPhone group options can be found by visiting http://groups.google.com/group/viphone?hl=en. --- You received this message because you are subscribed to the Google Groups "VIPhone" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/groups/opt_out.
