Did you try the tip I gave in my last message? Running it on the 4s and the tip I gave works for me.
Sent from my iPhone On Jul 12, 2013, at 3:13 PM, "Brent Harding" <br...@hostany.net> wrote: > For me, on the 4S, VO dies right when I launch the app. I haven't tried it by > closing VO before launching. > > ----- Original Message ----- > From: Ben Blatchford > To: viphone@googlegroups.com > Cc: <viphone@googlegroups.com> > Sent: Friday, July 12, 2013 5:05 PM > Subject: Re: Very interesting news about Fire 2 recorder > > What I do is when I double tap the add button and VoiceOver dies, I doubletap > with two fingers to bring VoiceOber back on and I do another two finger > double To keep voiceover and stop music playing. That always works for me. > > Sent from my iPhone > > On Jul 12, 2013, at 2:49 PM, "Neal Ewers" <neal.ew...@ravenswood.org> wrote: > >> Esther, as per usual, you are full of lengthy, sound advice. There are a >> couple things to add here. My Fire 2 app dies as soon as I open it. It not >> only dies, but the screen is frozen, so nothing can be acted upon. I >> have had sighted assistance look at what happens and nothing we do changes >> anything. Now, this might be different on other people’s devices. If, >> however, you have my problem, I would suggest that you turn VoiceOver >> off before you open the app. Then follow Esther’s very concise >> instructions. On the other hand, if your app does not die right away, >> her instructions can likely be followed to the letter. >> Let’s hope Rode brings back the functionality of this app. >> Thanks again Esther. >> Neal >> From: viphone@googlegroups.com [mailto:viphone@googlegroups.com] On Behalf >> Of Esther >> Sent: Friday, July 12, 2013 4:06 PM >> To: viphone@googlegroups.com >> Subject: Re: Very interesting news about Fire 2 recorder >> Hi Neal, Brent, Cokes, and Others who asked about FiRe 2, >> Neal's correct that earlier versions of FiRe 2 from January at the beginning >> of this year, up to the last version (released May 28, 2013), worked with >> VoiceOver. The FiRe 2 app got purchased by RØDE microphones, who will be >> taking over support for the app from Audiofile Engineering. They announced >> this on the RØDE microphones web site on July 2nd. >> If you have an older version of the app that you can revert to, by deleting >> the latest version on your iOS device and using iTunes on your computer to >> sync this across to your device, you can still use the app. There's also a >> clunky way to get the audio back using the latest version, provided that you >> don't want to change the recording specs for bit rate on the configuration >> screen. It's based on being to navigate the controls of the screen by >> knowing where the control sequence is without audio feedback from VoiceOver, >> because you lose the VOiceOver audio when you double tap the "Recordings >> List Configure Input" button in the bottom left corner of the "Recordings" >> screen, and you don't get it back until you double tap the "Recordings List >> Add" button in the bottom right corner of the same "Recordings" screen. >> So, if you aren't changing the hardware configuration of recording setup or >> the recording bit rate, which is set to 44.1 KHz by default., do the >> following when you start a new recording: >> 1. Double tap the "Recordings List Add" button in the bottom right corner of >> the "Recordings" screen. This is where you lose audio from VoiceOver, >> because the app launches the configuration screen, as though you double >> tapped the "Recordings List Configure Input" button. However, focus will be >> on the "Cancel, back" button, so double tap to get out of the configuration >> screen. >> 2. You'll be taken back to the "Recordings" screen, still without VoiceOver >> audio. Do a four finger tap on the bottom half of the screen to move to the >> last element of the screen, which is the "Recordings List Add" button, and >> then double tap. >> 3. At this point you'll be in the screen for the recording you just added, >> and should be able to record normally. If you don't have the "Record" >> button, navigate to the "Settings" button at the bottom of the screen and >> double tap. Navigate to "Transport" and make sure that "Button Controls" >> switch under the Record button heading of the Transport screen is set to >> "on". Then navigate back to your recording and record as usual. >> Once you've done this, you can add recordings with the "Recordings List Add" >> button on the Recordings screen and make new recordings as long as the app >> is open without losing VoiceOver. But if you close the app, you'll have to >> go through this again to start your recordings. >> I haven't used additional stereo mic connections with FiRe. If you want to >> save those settings, I think that when you reach the configure screen, >> after about 5 or so seconds of checking for your hardware configuration, the >> app will add stereo channels to the end of the screen. Neal can probably >> tell you whether this is selected by default. If you want to save this >> setting, and it is selected by default, just flick twice to the right and >> double tap. You're moving from the default focus of the "Cancel" button at >> the top left of the configure screen, to the screen heading, and then to the >> "Save" button. Again, you'll be at the Recordings screen, and will want to >> pick up at step 2., where you do a four finger tap on the bottom half of the >> screen to move to the "Recordings List Add" button and double tap to get >> back your VoiceOver audio. >> Can people try this and check that it works for them? >> HTH. Cheers, >> Esther >> On 12 Jul 2013, at 08:24, Neal Ewers wrote: >> >> >> Hi, previous versions did work. The last one totally crashed VoiceOver. I >> have no clue what Rode will do with this. I will just have to wait and see. >> Neal >> From: viphone@googlegroups.com [mailto:viphone@googlegroups.com] On Behalf >> Of Brent Harding >> Sent: Friday, July 12, 2013 11:44 AM >> To: viphone@googlegroups.com >> Subject: Re: Very interesting news about Fire 2 recorder -- You received this message because you are subscribed to the "VIPhone" Google Group. Post a new message to VIPhone by emailing viphone@googlegroups.com. Search and view the VIPhone archives by visiting http://www.mail-archive.com/viphone@googlegroups.com/. Reach the VIPhone owner and moderators by emailing viphone+ow...@googlegroups.com. Unsubscribe and leave VIPhone by emailing viphone+unsubscr...@googlegroups.com. More VIPhone group options can be found by visiting http://groups.google.com/group/viphone?hl=en. --- You received this message because you are subscribed to the Google Groups "VIPhone" group. To unsubscribe from this group and stop receiving emails from it, send an email to viphone+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/groups/opt_out.
