Hello Paul, I am not Anne. But I think I could help. There is a switch for the 12 battery pack. Look on the rear where the cord protrudes out of the pack, and you will see a very small switch. It moves from left to right and back and forth. I hope this helps.
E V -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Paul Hunt Sent: Saturday, March 22, 2014 8:28 AM To: [email protected] Subject: Re: Setting up the StandScan Pro Hello Anne. Thanks for your descriptions. I'll try setting up the Standscan later today. I have one question. Why is there a switch on the nine volt battery pack but no switch on the twelve volt battery pack? Thanks so much. > On Mar 20, 2014, at 4:35 PM, Anne Robertson <[email protected]> wrote: > > Hello Paul, > > I'll start with the accessories. The small box with the switch is the holder for a 9 v battery. This is a battery with two terminals and it is not provided with the StandScan Pro. > > The long box holds 8 AA batteries and these are not supplied either. > > So, you have the choice of connecting your StandScan Pro to mains electricity, to a 12 v battery pack or to a 9 v battery. > > Now to setting up your StandScan Pro. Lay the StandScan on a table as though it were a large envelope with a flap that will open away from you. This flap is held down by magnets so just pull it up. > > You should now be able to unfold the next layer of the package to the left. You should find crease marks on the left-hand piece, one at the front, and one at the back. If you follow along one of these creases, you'll find that it gradually gets closer to the centre of the piece, and at the far left edge, you'll find a circular lump at either side of the crease. Fold the outer edge upwards along the crease so that you have a long thin triangle standing up at right angles to the table. > > You do this at the front and at the back, then you unfold the next two layers out to the right. You'll find that the third section from the left is a mirror image of the left-hand section and has the same creases in it. > > The right-hand piece is the top of the box and has a hole in its centre and the LEDs next to a crease a couple of inches from its back edge. > > Raise the left-hand piece and then the back piece and you should be able to connect the magnets on the back triangle of the left side and the back. Make sure that the small flap does not close. > > The third section attaches to the back in the same way and the right-hand section comes over the top and has edges that fold down and meet with magnets on all four sides. > > Once assembled, the cable should protrude from the upper back left corner, and you should have an open side in front of you. > > If this still doesn't make sense, you'll need sighted help. > > Cheers, > > Anne > > >> On 20 Mar 2014, at 19:41, Paul Hunt <[email protected]> wrote: >> >> Hello everyone. I got my Standscan pro today and have some questions. >> First, I've looked ad gthe description and don't understand the >> assembly instructions that Anne posted. I may need some sighted >> assistance. There are three accessories that came with my Standscan. >> One is an AC adapter. There is a box with a switch on it that has a >> short cable that connects to the cable from the Standscan pro. >> There's a third long narrow box with a cable on one end. I assume >> that this is a battery pack. First, how do I charge the battery pack? >> What is the function of the box with the switch? It appears that all >> three boxes connect to the Standscan pro. >> >> -----Original Message----- >> From: [email protected] [mailto:[email protected]] On >> Behalf Of Anne Robertson >> Sent: Sunday, March 16, 2014 5:58 PM >> To: [email protected] [email protected] >> Subject: Setting up the StandScan Pro >> >> Hello everyone, >> >> Here is a description of how to set up the StandScan Pro that I >> posted almost a year ago. >> >> >> Lay the folded StandScan on a table with the small flap away from you. >> Open the small flap and fold back the body of the StandScan towards you. >> Now the topmost piece should open to the left, and the remaining part >> will open to the right but will still be a double thickness. >> Open the final piece to the right. >> Go to the lefthand piece and you'll find that there is a crease >> running from where it joins the second piece to the lefthand edge, a few centimetres in. >> Fold along this crease making an elongated triangle. >> The same thing can be found on the back edge of the same piece, and >> on the front and back edges of the third section. >> The piece at the extreme right is the top and you can find the LEDs >> along its back edge, and the cable at its back left corner. >> Lift the righthand section and lift the lefthand section, then fold >> over the flap at the end of the section with the LEDs so that the >> magnets meet the magnets on the lefthand section. >> A flap of the top section folds down to engage with the magnets on >> the triangular pieces, and the piece still lying flat at the back >> lifts up to meet the top and the triangular side pieces at the back. >> Your StandScan should now look like a large box with an open front >> and a short cable coming out of the upper back lefthand corner. >> >> Cheers, >> >> Anne >> >> -- >> You received this message because you are subscribed to the "VIPhone" >> Google Group. >> >> Post a new message to VIPhone by emailing [email protected]. >> >> Search and view the VIPhone archives by visiting >> http://www.mail-archive.com/[email protected]/. >> >> Reach the VIPhone owner and moderators by emailing >> [email protected]. >> >> Unsubscribe and leave VIPhone by emailing >> [email protected]. >> >> More VIPhone group options can be found by visiting >> http://groups.google.com/group/viphone?hl=en. >> --- >> You received this message because you are subscribed to the Google >> Groups "VIPhone" group. >> To unsubscribe from this group and stop receiving emails from it, >> send an email to [email protected]. >> For more options, visit https://groups.google.com/d/optout. >> >> -- >> The following information is important for all members of the viphone list. All new members to the this list are moderated by default. If you have any questions or concerns about the running of this list, or if you feel that a member's post is inappropriate, please contact the owners or moderators directly rather than posting on the list itself. The archives for this list can be searched at http://www.mail-archive.com/[email protected]/. >> --- >> You received this message because you are subscribed to the Google Groups "VIPhone" group. >> To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. >> To post to this group, send email to [email protected]. >> Visit this group at http://groups.google.com/group/viphone. >> For more options, visit https://groups.google.com/d/optout. > > -- > The following information is important for all members of the viphone list. All new members to the this list are moderated by default. If you have any questions or concerns about the running of this list, or if you feel that a member's post is inappropriate, please contact the owners or moderators directly rather than posting on the list itself. The archives for this list can be searched at http://www.mail-archive.com/[email protected]/. > --- > You received this message because you are subscribed to the Google Groups "VIPhone" group. > To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. > To post to this group, send email to [email protected]. > Visit this group at http://groups.google.com/group/viphone. > For more options, visit https://groups.google.com/d/optout. -- The following information is important for all members of the viphone list. All new members to the this list are moderated by default. If you have any questions or concerns about the running of this list, or if you feel that a member's post is inappropriate, please contact the owners or moderators directly rather than posting on the list itself. The archives for this list can be searched at http://www.mail-archive.com/[email protected]/. --- You received this message because you are subscribed to the Google Groups "VIPhone" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To post to this group, send email to [email protected]. Visit this group at http://groups.google.com/group/viphone. For more options, visit https://groups.google.com/d/optout. -- The following information is important for all members of the viphone list. All new members to the this list are moderated by default. If you have any questions or concerns about the running of this list, or if you feel that a member's post is inappropriate, please contact the owners or moderators directly rather than posting on the list itself. The archives for this list can be searched at http://www.mail-archive.com/[email protected]/. --- You received this message because you are subscribed to the Google Groups "VIPhone" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To post to this group, send email to [email protected]. Visit this group at http://groups.google.com/group/viphone. For more options, visit https://groups.google.com/d/optout.
