Yep, I’ll just swap to the test server. Thanks On Tue, Sep 4, 2018 at 11:38 PM Colin Larsen <[email protected]> wrote:
> You may need to change unit_system to match yours is all > > On Wed, 5 Sep 2018, 15:25 G Hammer, <[email protected]> wrote: > >> Thanks. >> I’ll swap to test tomorrow. >> >> >> It’s always something... >> >> >> On Tue, Sep 4, 2018 at 11:01 PM Colin Larsen <[email protected]> >> wrote: >> >>> Here's mine that work fine >>> >>> >>> Weewx.conf >>> >>> [[MQTT]] >>> >>> #This section is for the MQTT service setup >>> >>> server_url = mqtt://test.mosquitto.org:1883/ >>> >>> topic = weather/41south >>> >>> unit_system = METRIC >>> >>> binding = archive, loop >>> >>> aggregation = aggregate >>> >>> Skin.conf >>> >>> >>> # MQTT Defaults >>> >>> mqtt_enabled = 1 >>> >>> mqtt_host = "test.mosquitto.org" >>> >>> mqtt_port = 8080 >>> >>> mqtt_ssl = 0 >>> >>> mqtt_topic = "weather/41south/#" >>> >>> disconnect_live_website_visitor = 1800000 >>> >>> On Wed, Sep 5, 2018 at 2:31 PM G Hammer <[email protected]> wrote: >>> >>>> I can say that my mosquitto install is not using websockets. >>>> With mqtt-spy on the server, I can set it up for either default or >>>> websockets. >>>> Default works fine, websockets does not. >>>> Though only item I changed in the mosquitto.conf is protocol websockets >>>> >>>> So, stumped. Anyone have a working mosquitto install that they would >>>> share the conf? >>>> >>>> >>>> >>>> >>>> On Tuesday, September 4, 2018 at 5:53:18 PM UTC-4, Pat wrote: >>>>> >>>>> On second glance, use this tool instead. >>>>> http://mitsuruog.github.io/what-mqtt/ since it can support SSL >>>>> brokers (even though it's not documented). Maybe I should setup my own >>>>> websocket test tool? :) >>>>> >>>>> If your MQTT is setup with SSL, then you'll want to connect to secure >>>>> websockets with WSS. Otherwise it'll use normal websockets which is ws. >>>>> >>>>> Example: wss://your.broker.com:port for secure. Then subscribe to >>>>> your topic and see if its working >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> On Tuesday, September 4, 2018 at 5:44:14 PM UTC-4, Pat wrote: >>>>>> >>>>>> The skin - at its core - will show the data from the previous >>>>>> archive. Once connected it'll update those fields from the MQTT messages. >>>>>> >>>>>> The MQTT will show "connected" in the status bar once it gets a >>>>>> timestamp from the published message. >>>>>> >>>>>> Check to make sure your broker allows websockets. To validate you can >>>>>> use this test tool. http://www.hivemq.com/demos/websocket-client/ >>>>>> >>>>>> If that test tool works, make sure your config options are correct. >>>>>> >>>>>> Anything in the Chrome console log? >>>>>> >>>>>> On Tuesday, September 4, 2018 at 4:53:08 PM UTC-4, G Hammer wrote: >>>>>>> >>>>>>> Hi Colin, >>>>>>> >>>>>>> I don't think the problem is with sending or retrieving data from >>>>>>> the MQTT server, I have done both the test.mosquitto.org and then >>>>>>> installed mosquitto on my server. >>>>>>> I used MQTT.fx to subscribe to both and both are getting the data. >>>>>>> The skin is getting data as it shows the temp, humidity, wind, but >>>>>>> never shows a connection and never completes the main page. Graphs on >>>>>>> the >>>>>>> page are missing/blank but shown on the Graphs page. >>>>>>> >>>>>>> You can better understand the issue by visiting the site. After you >>>>>>> are there for 30 seconds or so, refresh the page and see that the data >>>>>>> has >>>>>>> changed. >>>>>>> My Weather Site <https://ghammer.net/weather/> >>>>>>> >>>>>> >>>>>>> -- >>>> You received this message because you are subscribed to the Google >>>> Groups "weewx-user" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to [email protected]. >>>> For more options, visit https://groups.google.com/d/optout. >>>> >>> -- >>> You received this message because you are subscribed to a topic in the >>> Google Groups "weewx-user" group. >>> To unsubscribe from this topic, visit >>> https://groups.google.com/d/topic/weewx-user/81PjpX0Ajas/unsubscribe. >>> To unsubscribe from this group and all its topics, send an email to >>> [email protected]. >>> For more options, visit https://groups.google.com/d/optout. >> >> >>> -- >> You received this message because you are subscribed to the Google Groups >> "weewx-user" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> For more options, visit https://groups.google.com/d/optout. >> > -- > You received this message because you are subscribed to a topic in the > Google Groups "weewx-user" group. > To unsubscribe from this topic, visit > https://groups.google.com/d/topic/weewx-user/81PjpX0Ajas/unsubscribe. > To unsubscribe from this group and all its topics, send an email to > [email protected]. > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
