I am not sure I understand what you think is wrong with the readings of Pressure 29.89 Barometer 32.609 Altimeter 32.40 and why you believe something is wrong
On Friday, 14 February 2020 05:57:36 UTC+2, Dan Blanchard wrote: > > Altitude is 2,320 ft. and the values are in the screen shot on the > previous post. Did you see that? > > On Thursday, February 13, 2020 at 7:16:11 PM UTC-8, Andrew Milner wrote: >> >> I give up - looks correct to me. >> >> have you run from the command line and seen the LOOP and REC data weewx >> is receiving? >> >> what altitude is your station, and what values are you currently getting >> for pressure, barometer and altimeter? >> >> On Thursday, 13 February 2020 22:10:08 UTC+2, Dan Blanchard wrote: >>> >>> I don't know, but that makes sense so I did it. I'm still not getting >>> desired results though. >>> >>> On Thursday, February 13, 2020 at 9:38:55 AM UTC-8, Kevin Davis wrote: >>>> >>>> Do you need a space between your minus sign and the adjustment value? >>>> >>>> On Thu, Feb 13, 2020 at 9:32 AM Dan Blanchard <[email protected]> >>>> wrote: >>>> >>>>> Hey Andrew, will you please look at the attached screen shots and let >>>>> me know if this looks correct? >>>>> >>>>> Do I need to restart (sudo /etc/init.d/weewx restart) after I make >>>>> these changes? I have and the changes don't seem to be taking effect. >>>>> Is >>>>> there something else I need to do? >>>>> >>>>> With regard to the barometer and altimeter having the same settings; I >>>>> have probably misled. They are not exactly the same but they were >>>>> relatively close to each other compared to the pressure value. Here are >>>>> the current readings as of now when I run sudo weewxd >>>>> /etc/weewx/weewx.conf. >>>>> >>>>> pressure: 29.98 >>>>> altimeter: 32.57 >>>>> barometer: 32.74 >>>>> >>>>> >>>>> >>>>> On Thursday, February 13, 2020 at 12:07:50 AM UTC-8, Andrew Milner >>>>> wrote: >>>>>> >>>>>> If you have a LaCrosse WS28xx station then according to the hardware >>>>>> guide the station outputs PRESSURE in weewx terminology - regardless of >>>>>> what LaCrosse call it - and weewx should calculate barometer and >>>>>> altimeter >>>>>> settings. >>>>>> >>>>>> If pressure is incorrect then it can be adjusted as you specified - >>>>>> by adjusting pressure (not barometer or altimeter) >>>>>> >>>>>> Make sure pressure is set to use hardware and barometer and altimeter >>>>>> are set to use software. >>>>>> >>>>>> I am surprised barometer and altimeter are the same values - have you >>>>>> set the station's altitude in weewx.conf, and have you specified >>>>>> software >>>>>> generation for the values? >>>>>> >>>>>> >>>>>> >>>>>> On Thursday, 13 February 2020 09:23:27 UTC+2, Dan Blanchard wrote: >>>>>>> >>>>>>> Andrew, are you suggesting that I make a 'correction' entry under >>>>>>> [StdCalibrate] such as barometer = barometer -2.8 assuming that I am >>>>>>> getting a pressure reading of 30.13 and Barometer and ALtitude >>>>>>> readings of >>>>>>> 32.93? >>>>>>> >>>>>>> (see attached screenshot) >>>>>>> >>>>>>> On Wednesday, February 12, 2020 at 7:42:08 PM UTC-8, Andrew Milner >>>>>>> wrote: >>>>>>>> >>>>>>>> 1. use stdcalibrate section of weewx.conf >>>>>>>> http://weewx.com/docs/usersguide.htm#StdCalibrate >>>>>>>> 2. FO station = Fine Offset weather station >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> On Wednesday, 12 February 2020 22:15:48 UTC+2, Dan Blanchard wrote: >>>>>>>>> >>>>>>>>> Andrew, how do I calibrate the pressure in weewx? Also, what's a >>>>>>>>> FO station? >>>>>>>>> >>>>>>>>> On Tuesday, February 11, 2020 at 8:01:08 PM UTC-8, Andrew Milner >>>>>>>>> wrote: >>>>>>>>>> >>>>>>>>>> check that the absolute pressure is correct - I have had a FO >>>>>>>>>> station which had a dodgy pressure sensor before now. Calibrating >>>>>>>>>> pressure >>>>>>>>>> in weewx solved it. >>>>>>>>>> >>>>>>>>> -- >>>>> You received this message because you are subscribed to the Google >>>>> Groups "weewx-user" group. >>>>> To unsubscribe from this group and stop receiving emails from it, send >>>>> an email to [email protected]. >>>>> To view this discussion on the web visit >>>>> https://groups.google.com/d/msgid/weewx-user/08c79655-b1af-4134-9a2b-82a4f52f051f%40googlegroups.com >>>>> >>>>> <https://groups.google.com/d/msgid/weewx-user/08c79655-b1af-4134-9a2b-82a4f52f051f%40googlegroups.com?utm_medium=email&utm_source=footer> >>>>> . >>>>> >>>> -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/weewx-user/9a0d6cfa-8346-4bc6-95c8-89c6a70e3365%40googlegroups.com.
