This is what I'm seeing...
pi@raspitest:~ $ cd /home/weewx/bin/user pi@raspitest:/home/weewx/bin/user $ dir extensions.py HP1000.py __init__.py installer __pycache__ pi@raspitest:/home/weewx/bin/user $ sudo nano HP1000.py # # Copyright (c) 2017 Susan Mackay # acknowledging that this driver code originated from and # is structured in a similar way to the Weewx 'Simulator' driver code # that carries the following line: # # # """hp1000 driver for the weewx weather system This driver communicates with the HP1000/WS1001/XC0422 and whatever other clone weather stations respond over the LAN to the 'easyweather' protocol. Communication starts with a UDP IP broadcast on the local subnet to port 6000 to see if the weather station responds. The broadcast packet is structured as: Offset Value Structure Comment 0x00 PC2000 8 byte string Identifies the calling station 0x08 SEARCH 8 byte string Command On Wednesday, 2 September 2020 at 23:03:15 UTC+1 [email protected] wrote: > Hi Gary, > > Yes to both questions. > > Thanks for your help > > On Wednesday, 2 September 2020 at 22:28:23 UTC+1 gjr80 wrote: > >> OK, let’s start with the obvious. Is HP1000.py in /home/weewx/bin/user >> and if you view the contents of the file is it legible code? >> >> Gary >> On Thursday, 3 September 2020 at 07:08:58 UTC+10 [email protected] wrote: >> >>> this is what i'm seeing >>> >>> pi@raspitest:/var/tmp $ sudo /home/weewx/bin/wee_extension >>> --install=/var/tmp/HP1000-master/HP1000.tar.gz >>> Request to install '/var/tmp/HP1000-master/HP1000.tar.gz' >>> Extracting from tar archive /var/tmp/HP1000-master/HP1000.tar.gz >>> Saving installer file to /home/weewx/bin/user/installer/HP1000 >>> Finished installing extension '/var/tmp/HP1000-master/HP1000.tar.gz' >>> pi@raspitest:/var/tmp $ /home/weewx/bin/wee_config --list-drivers >>> >>> Module name Driver name Version Status >>> weewx.drivers.acurite AcuRite 0.4 >>> weewx.drivers.cc3000 CC3000 0.40 >>> weewx.drivers.fousb FineOffsetUSB 1.20 >>> weewx.drivers.simulator Simulator 3.2 >>> weewx.drivers.te923 TE923 0.41 >>> weewx.drivers.ultimeter Ultimeter 0.41 >>> weewx.drivers.vantage Vantage 3.2.1 >>> weewx.drivers.wmr100 WMR100 3.5.0 >>> weewx.drivers.wmr200 WMR200 3.5.0 >>> weewx.drivers.wmr300 WMR300 0.33 >>> weewx.drivers.wmr9x8 WMR9x8 3.4.1 >>> weewx.drivers.ws1 WS1 0.41 >>> weewx.drivers.ws23xx WS23xx 0.41 >>> weewx.drivers.ws28xx WS28xx 0.51 >>> On Wednesday, 2 September 2020 at 21:59:38 UTC+1 [email protected] >>> wrote: >>> >>>> Apologies for resurrecting an old thread but I'm trying to do a fresh >>>> install using the commands listed above, using Weewx 4.1.1 and the HP1000 >>>> driver is not appearing in the list so it cannot be chosen. Has anything >>>> fundamental changes between the previous and current weewx versions? >>>> >>>> Thanks >>>> >>>> On Tuesday, 15 October 2019 at 19:50:53 UTC+1 [email protected] wrote: >>>> >>>>> Finally, it's working. >>>>> >>>>> Thanks all for your help. >>>>> >>>>> >>>>> On Tuesday, 15 October 2019 12:51:24 UTC+1, Matt wrote: >>>>> >>>>>> Hi All, >>>>>> >>>>>> First post. >>>>>> >>>>>> I got Weewx set up on a brand new Raspberry Pi 3 model B yesterday. >>>>>> I saw that it was posting data but last night most of the data was >>>>>> incorrect (e.g. outside temp 0 degrees C when it was actually 10 >>>>>> degrees). >>>>>> I decided to leave it and went to bed. Today I am seeing better values >>>>>> but >>>>>> all readings appear to be summing/appending to the previous reading. >>>>>> For >>>>>> example, the temperature has risen from 0 to around 21 degrees very >>>>>> uniformly. The actual temperature is around 13 degrees. >>>>>> >>>>>> I have an Aercus station, identical to Fine Offset HP1000. I have >>>>>> set Weewx driver to both 'simulator' and 'Fine Offset' with no change in >>>>>> data. >>>>>> >>>>>> I read somewhere about an HP1000 driver written by aussie susan but >>>>>> editing the daemon file was beyond my capabilities so I couldn't proceed >>>>>> with it. >>>>>> >>>>>> My station can be seen at: >>>>>> https://www.pwsweather.com/obs/ILITTLEW9.html# >>>>>> >>>>>> I appreciate that I will need to provide logs etc, but I am work at >>>>>> the moment and will upload logs later. I just wanted to get the post up >>>>>> to >>>>>> see if anyone had experienced anything similar or has any advice for a >>>>>> newbie. >>>>>> >>>>>> I love the functionality of weewx and look forward to using it. >>>>>> >>>>>> Many thanks in advance. >>>>>> >>>>>> Matt >>>>>> >>>>> -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/weewx-user/61d4972e-636d-4a4b-b60f-2512fe7b2137n%40googlegroups.com.
