If that's the case, it would be useful to see more of the log, in particular of the time when the report should have been run.
It's possible that the logger in your Davis is suffering from corrupted memory, but it's impossible to say without seeing the log. See the wiki <https://github.com/weewx/weewx/wiki/Troubleshooting-the-Davis-Vantage-station#weewx-generates-html-pages-but-it-does-not-update-them> . On Tue, Feb 8, 2022 at 4:59 AM Marek Šnapka <[email protected]> wrote: > Hello, Tom, > thanks, the 30 min archive interval is set up on purpose. > > However, after 12 hours, different configs and a full machine reinstall, > the system was able to create a report only once, then the index.html with > current weather has not been updated, but monthly reports were OK. > > Then I reinstalled the app again, configured it from the scratch...nothing. > > Thanks. > > Marek > Dne úterý 8. února 2022 v 13:51:52 UTC+1 uživatel [email protected] napsal: > >> Hello, Markek >> >> The first report is not generated until the end of the first archive >> interval. No report is generated on catchup. >> >> Your archive interval is rather long (1/2 hour), so you will have to wait >> a bit to see the first one. >> >> To change the archive interval, use the utility wee_device with option >> --set-interval >> <http://www.weewx.com/docs/hardware.htm#vantage_archive_interval>. >> >> On Tue, Feb 8, 2022 at 3:21 AM Marek Šnapka <[email protected]> >> wrote: >> >>> Hello, I have tried many threads any many things, however I am still >>> unsuccessful in getting WeeWX into the working state. >>> >>> I have installed a HyperV VM (gen2) with Debian 11: >>> >>> ###################################### >>> Icon name: computer-vm >>> Chassis: vm >>> Virtualization: microsoft >>> Operating System: Debian GNU/Linux 11 (bullseye) >>> Kernel: Linux 5.10.0-11-amd64 >>> Architecture: x86-64 >>> ####################################### >>> >>> >>> I successfully installed WeeWX using the docs: >>> https://weewx.com/docs/debian.htm >>> >>> I configured WeeWX to use my Vantage Pro2 station (via WeatherLink IP) >>> using the following config: >>> >>> ####################################### >>> # WEEWX CONFIGURATION FILE >>> # >>> # Copyright (c) 2009-2021 Tom Keffer <[email protected]> >>> # See the file LICENSE.txt for your rights. >>> >>> >>> ############################################################################## >>> >>> # This section is for general configuration information. >>> >>> # Set to 1 for extra debug info, otherwise comment it out or set to zero >>> debug = 1 >>> >>> # Root directory of the weewx data file hierarchy for this station >>> WEEWX_ROOT = / >>> >>> # Whether to log successful operations >>> log_success = True >>> >>> # Whether to log unsuccessful operations >>> log_failure = True >>> >>> # How long to wait before timing out a socket (FTP, HTTP) connection >>> socket_timeout = 20 >>> >>> # Do not modify this. It is used when installing and updating weewx. >>> version = 4.6.0 >>> >>> >>> ############################################################################## >>> >>> # This section is for information about the station. >>> >>> [Station] >>> >>> # Description of the station location >>> location = "Opava, Czech Republic" >>> >>> # Latitude in decimal degrees. Negative for southern hemisphere >>> latitude = 49.9296003 >>> # Longitude in decimal degrees. Negative for western hemisphere. >>> longitude = 17.8794469 >>> >>> # Altitude of the station, with the unit it is in. This is used only >>> # if the hardware cannot supply a value. >>> altitude = 270, meter >>> >>> # Set to type of station hardware. There must be a corresponding >>> stanza >>> # in this file, which includes a value for the 'driver' option. >>> station_type = Vantage >>> >>> # If you have a website, you may specify an URL. This is required if >>> you >>> # intend to register your station. >>> #station_url = http://www.example.com >>> >>> # The start of the rain year (1=January; 10=October, etc.). This is >>> # downloaded from the station if the hardware supports it. >>> rain_year_start = 1 >>> >>> # Start of week (0=Monday, 6=Sunday) >>> week_start = 0 >>> >>> >>> ############################################################################## >>> >>> [Vantage] >>> # This section is for the Davis Vantage series of weather stations. >>> >>> # Connection type: serial or ethernet >>> # serial (the classic VantagePro) >>> # ethernet (the WeatherLinkIP or Serial-Ethernet bridge) >>> type = ethernet >>> >>> # If the connection type is serial, a port must be specified: >>> # Debian, Ubuntu, Redhat, Fedora, and SuSE: >>> # /dev/ttyUSB0 is a common USB port name >>> # /dev/ttyS0 is a common serial port name >>> # BSD: >>> # /dev/cuaU0 is a common serial port name >>> # port = /dev/ttyUSB0 >>> >>> # If the connection type is ethernet, an IP Address/hostname is >>> required: >>> host = 192.168.9.2 >>> >>> ###################################################### >>> # The rest of this section rarely needs any attention. >>> # You can safely leave it "as is." >>> ###################################################### >>> >>> # Serial baud rate (usually 19200) >>> baudrate = 19200 >>> >>> # TCP port (when using the WeatherLinkIP) >>> tcp_port = 8080 >>> >>> # TCP send delay (when using the WeatherLinkIP): >>> tcp_send_delay = 0.5 >>> >>> # The type of LOOP packet to request: 1 = LOOP1; 2 = LOOP2; 3 = both >>> loop_request = 1 >>> >>> # The id of your ISS station (usually 1). If you use a wind meter >>> connected >>> # to a anemometer transmitter kit, use its id >>> iss_id = 1 >>> >>> # How long to wait for a response from the station before giving up >>> (in >>> # seconds; must be greater than 2) >>> timeout = 5 >>> >>> # How long to wait before trying again (in seconds) >>> wait_before_retry = 15 >>> >>> # How many times to try before giving up: >>> max_tries = 60 >>> >>> # Vantage model Type: 1 = Vantage Pro; 2 = Vantage Pro2 >>> model_type = 2 >>> >>> # The driver to use: >>> driver = weewx.drivers.vantage >>> >>> >>> ############################################################################## >>> >>> # This section is for uploading data to Internet sites >>> >>> [StdRESTful] >>> >>> [[StationRegistry]] >>> # To register this weather station with weewx, set this to true, >>> # then fill out option 'station_url' above. >>> register_this_station = false >>> >>> [[AWEKAS]] >>> # This section is for configuring posts to AWEKAS. >>> >>> # If you wish to post to AWEKAS, set the option 'enable' to >>> true, then specify a username >>> # and password. To guard against parsing errors, put the >>> password in quotes. >>> enable = false >>> username = replace_me >>> password = replace_me >>> >>> [[CWOP]] >>> # This section is for configuring posts to CWOP. >>> >>> # If you wish to post to CWOP, set the option 'enable' to true, >>> # then specify the station ID (e.g., CW1234). >>> enable = false >>> station = replace_me >>> # If this is an APRS (radio amateur) station, specify the >>> # passcode (e.g., 12345). Otherwise, ignore. >>> passcode = replace_me >>> >>> >>> [[PWSweather]] >>> # This section is for configuring posts to PWSweather.com. >>> >>> # If you wish to post to PWSweather.com, set the option 'enable' >>> to true, then specify a >>> # station and password. To guard against parsing errors, put the >>> password in quotes. >>> enable = false >>> station = replace_me >>> password = replace_me >>> >>> [[WOW]] >>> # This section is for configuring posts to WOW. >>> >>> # If you wish to post to WOW, set the option 'enable' to true, >>> then specify a station and >>> # password. To guard against parsing errors, put the password in >>> quotes. >>> enable = false >>> station = replace_me >>> password = replace_me >>> >>> [[Wunderground]] >>> # This section is for configuring posts to the Weather >>> Underground. >>> >>> # If you wish to post to the Weather Underground, set the option >>> 'enable' to true, then >>> # specify a station (e.g., 'KORHOODR3') and password. To guard >>> against parsing errors, put >>> # the password in quotes. >>> enable = false >>> station = replace_me >>> password = replace_me >>> >>> # If you plan on using wunderfixer, set the following >>> # to your API key: >>> api_key = replace_me >>> >>> # Set the following to True to have weewx use the WU "Rapidfire" >>> # protocol. Not all hardware can support it. See the User's >>> Guide. >>> rapidfire = False >>> >>> >>> ############################################################################## >>> >>> # This section specifies what reports, using which skins, to generate. >>> >>> [StdReport] >>> >>> # Where the skins reside, relative to WEEWX_ROOT >>> SKIN_ROOT = /etc/weewx/skins >>> >>> # Where the generated reports should go, relative to WEEWX_ROOT >>> HTML_ROOT = /var/www/html/weewx >>> >>> # The database binding indicates which data should be used in >>> reports. >>> data_binding = wx_binding >>> >>> # Whether to log a successful operation >>> log_success = True >>> >>> # Whether to log an unsuccessful operation >>> log_failure = True >>> >>> # Each of the following subsections defines a report that will be >>> run. >>> # See the customizing guide to change the units, plot types and line >>> # colors, modify the fonts, display additional sensor data, and other >>> # customizations. Many of those changes can be made here by >>> overriding >>> # parameters, or by modifying templates within the skin itself. >>> >>> [[SeasonsReport]] >>> # The SeasonsReport uses the 'Seasons' skin, which contains the >>> # images, templates and plots for the report. >>> skin = Seasons >>> enable = true >>> >>> [[SmartphoneReport]] >>> # The SmartphoneReport uses the 'Smartphone' skin, and the >>> images and >>> # files are placed in a dedicated subdirectory. >>> skin = Smartphone >>> enable = false >>> HTML_ROOT = /var/www/html/weewx/smartphone >>> >>> [[MobileReport]] >>> # The MobileReport uses the 'Mobile' skin, and the images and >>> files >>> # are placed in a dedicated subdirectory. >>> skin = Mobile >>> enable = false >>> HTML_ROOT = /var/www/html/weewx/mobile >>> >>> [[StandardReport]] >>> # This is the old "Standard" skin. By default, it is not enabled. >>> skin = Standard >>> enable = false >>> >>> [[FTP]] >>> # FTP'ing the results to a webserver is treated as just another >>> report, >>> # albeit one with an unusual report generator! >>> skin = Ftp >>> >>> # If you wish to use FTP, set "enable" to "true", then >>> # fill out the next four lines. >>> # Use quotes around passwords to guard against parsing errors. >>> enable = false >>> user = replace_me >>> password = replace_me >>> server = replace_me # The ftp server name, e.g, >>> www.myserver.org >>> path = replace_me # The destination directory, e.g., /weather >>> >>> # Set to True for an FTP over TLS (FTPS) connection. Not all >>> servers >>> # support this. >>> secure_ftp = False >>> >>> # To upload files from something other than what HTML_ROOT is set >>> # to above, specify a different HTML_ROOT here. >>> #HTML_ROOT = /var/www/html/weewx >>> >>> # Most FTP servers use port 21 >>> port = 21 >>> >>> # Set to 1 to use passive mode, zero for active mode >>> passive = 1 >>> >>> [[RSYNC]] >>> # rsync'ing to a webserver is treated as just another report >>> skin = Rsync >>> >>> # If you wish to use rsync, you must configure passwordless ssh >>> using >>> # public/private key authentication from the user account that >>> weewx >>> # runs to the user account on the remote machine where the files >>> # will be copied. >>> # >>> # If you wish to use rsync, set "enable" to "true", then >>> # fill out server, user, and path. >>> # The server should appear in your .ssh/config file. >>> # The user is the username used in the identity file. >>> # The path is the destination directory, such as >>> /var/www/html/weather. >>> # Be sure that the user has write permissions on the destination! >>> enable = false >>> server = replace_me >>> user = replace_me >>> path = replace_me >>> >>> # To upload files from something other than what HTML_ROOT is set >>> # to above, specify a different HTML_ROOT here. >>> #HTML_ROOT = /var/www/html/weewx >>> >>> # Rsync can be configured to remove files from the remote server >>> if >>> # they don't exist under HTML_ROOT locally. USE WITH CAUTION: if >>> you >>> # make a mistake in the remote path, you could could >>> unintentionally >>> # cause unrelated files to be deleted. Set to 1 to enable remote >>> file >>> # deletion, zero to allow files to accumulate remotely. >>> delete = 0 >>> >>> # Options in the [[Defaults]] section below will apply to all >>> reports. >>> # What follows are a few of the more popular options you may want to >>> # uncomment, then change. >>> [[Defaults]] >>> >>> # Which language to use for all reports. Not all skins support >>> all languages. >>> # You can override this for individual reports. >>> lang = en >>> >>> # Which unit system to use for all reports. Choices are 'us', >>> 'metric', or 'metricwx'. >>> # You can override this for individual reports. >>> unit_system = metricwx >>> >>> [[[Units]]] >>> >>> # Option "unit_system" above sets the general unit system, >>> but overriding specific unit >>> # groups is possible. These are popular choices. Uncomment >>> and set as appropriate. >>> # NB: The unit is always in the singular. I.e., >>> 'mile_per_hour', >>> # NOT 'miles_per_hour' >>> [[[[Groups]]]] >>> # group_altitude = meter # Options are >>> 'foot' or 'meter' >>> # group_pressure = mbar # Options are >>> 'inHg', 'mmHg', 'mbar', or 'hPa' >>> # group_rain = mm # Options are >>> 'inch', 'cm', or 'mm' >>> # group_rainrate = mm_per_hour # Options are >>> 'inch_per_hour', 'cm_per_hour', or 'mm_per_hour' >>> # The following line is used to keep the above lines >>> indented properly. >>> # It can be ignored. >>> unused = unused >>> >>> # Uncommenting the following section frequently results in >>> more >>> # attractive formatting of times and dates, but may not work >>> in >>> # your locale. >>> [[[[TimeFormats]]]] >>> # day = %H:%M >>> # week = %H:%M on %A >>> # month = %d-%b-%Y %H:%M >>> # year = %d-%b-%Y %H:%M >>> # rainyear = %d-%b-%Y %H:%M >>> # current = %d-%b-%Y %H:%M >>> # ephem_day = %H:%M >>> # ephem_year = %d-%b-%Y %H:%M >>> # The following line is used to keep the above lines >>> indented properly. >>> # It can be ignored. >>> unused = unused >>> >>> [[[Labels]]] >>> # Users frequently change the labels for these observation >>> types >>> [[[[Generic]]]] >>> # inHumidity = Inside Humidity >>> # inTemp = Inside Temperature >>> # outHumidity = Outside Humidity >>> # outTemp = Outside Temperature >>> # extraTemp1 = Temperature1 >>> # extraTemp2 = Temperature2 >>> # extraTemp3 = Temperature3 >>> # The following line is used to keep the above lines >>> indented properly. >>> # It can be ignored. >>> unused = unused >>> >>> >>> ############################################################################## >>> >>> # This service acts as a filter, converting the unit system coming from >>> # the hardware to a unit system in the database. >>> >>> [StdConvert] >>> >>> # The target_unit affects only the unit system in the database. Once >>> # chosen it cannot be changed without converting the entire database. >>> # Modification of target_unit after starting weewx will result in >>> # corrupt data - the database will contain a mix of US and METRIC >>> data. >>> # >>> # The value of target_unit does not affect the unit system for >>> # reporting - reports can display US, Metric, or any combination of >>> units. >>> # >>> # In most cases, target_unit should be left as the default: US >>> # >>> # In particular, those migrating from a standard wview installation >>> # should use US since that is what the wview database contains. >>> >>> # DO NOT MODIFY THIS VALUE UNLESS YOU KNOW WHAT YOU ARE DOING! >>> target_unit = US # Options are 'US', 'METRICWX', or 'METRIC' >>> >>> >>> ############################################################################## >>> >>> # This section can adjust data using calibration expressions. >>> >>> [StdCalibrate] >>> >>> [[Corrections]] >>> # For each type, an arbitrary calibration expression can be >>> given. >>> # It should be in the units defined in the StdConvert section. >>> # Example: >>> foo = foo + 0.2 >>> >>> >>> ############################################################################## >>> >>> # This section is for quality control checks. If units are not >>> specified, >>> # values must be in the units defined in the StdConvert section. >>> >>> [StdQC] >>> >>> [[MinMax]] >>> barometer = 26, 32.5, inHg >>> pressure = 24, 34.5, inHg >>> outTemp = -40, 120, degree_F >>> inTemp = 10, 120, degree_F >>> outHumidity = 0, 100 >>> inHumidity = 0, 100 >>> windSpeed = 0, 120, mile_per_hour >>> rain = 0, 10, inch >>> >>> >>> ############################################################################## >>> >>> # This section controls the origin of derived values. >>> >>> [StdWXCalculate] >>> >>> [[Calculations]] >>> # How to calculate derived quantities. Possible values are: >>> # hardware - use the value provided by hardware >>> # software - use the value calculated by weewx >>> # prefer_hardware - use value provide by hardware if available, >>> # otherwise use value calculated by weewx >>> >>> pressure = prefer_hardware >>> altimeter = prefer_hardware >>> appTemp = prefer_hardware >>> barometer = prefer_hardware >>> cloudbase = prefer_hardware >>> dewpoint = prefer_hardware >>> ET = prefer_hardware >>> heatindex = prefer_hardware >>> humidex = prefer_hardware >>> inDewpoint = prefer_hardware >>> maxSolarRad = prefer_hardware >>> rainRate = prefer_hardware >>> windchill = prefer_hardware >>> windrun = prefer_hardware >>> >>> >>> ############################################################################## >>> >>> # For hardware that supports it, this section controls how often the >>> # onboard clock gets updated. >>> >>> [StdTimeSynch] >>> >>> # How often to check the weather station clock for drift (in seconds) >>> clock_check = 14400 >>> >>> # How much it can drift before we will correct it (in seconds) >>> max_drift = 5 >>> >>> >>> ############################################################################## >>> >>> # This section is for configuring the archive service. >>> >>> [StdArchive] >>> >>> # If the station hardware supports data logging then the archive >>> interval >>> # will be downloaded from the station. Otherwise, specify it (in >>> seconds). >>> archive_interval = 1800 >>> >>> # If possible, new archive records are downloaded from the station >>> # hardware. If the hardware does not support this, then new archive >>> # records will be generated in software. >>> # Set the following to "software" to force software record >>> generation. >>> record_generation = hardware >>> >>> # Whether to include LOOP data in hi/low statistics >>> loop_hilo = True >>> >>> # The data binding used to save archive records >>> data_binding = wx_binding >>> >>> # Whether to log successful archive operations >>> log_success = True >>> >>> # Whether to log unsuccessful archive operations >>> log_failure = True >>> >>> >>> ############################################################################## >>> >>> # This section binds a data store to a database. >>> >>> [DataBindings] >>> >>> [[wx_binding]] >>> # The database must match one of the sections in [Databases]. >>> # This is likely to be the only option you would want to change. >>> database = archive_sqlite >>> # The name of the table within the database >>> table_name = archive >>> # The manager handles aggregation of data for historical >>> summaries >>> manager = weewx.manager.DaySummaryManager >>> # The schema defines the structure of the database. >>> # It is *only* used when the database is created. >>> schema = schemas.wview_extended.schema >>> >>> >>> ############################################################################## >>> >>> # This section defines various databases. >>> >>> [Databases] >>> >>> # A SQLite database is simply a single file >>> [[archive_sqlite]] >>> database_name = weewx.sdb >>> database_type = SQLite >>> >>> # MySQL >>> [[archive_mysql]] >>> database_name = weewx >>> database_type = MySQL >>> >>> >>> ############################################################################## >>> >>> # This section defines defaults for the different types of databases. >>> >>> [DatabaseTypes] >>> >>> # Defaults for SQLite databases >>> [[SQLite]] >>> driver = weedb.sqlite >>> # Directory in which the database files are located >>> SQLITE_ROOT = /var/lib/weewx >>> >>> # Defaults for MySQL databases >>> [[MySQL]] >>> driver = weedb.mysql >>> # The host where the database is located >>> host = localhost >>> # The user name for logging in to the host >>> user = weewx >>> # The password (use quotes to guard against parsing errors) >>> password = weewx >>> >>> >>> ############################################################################## >>> >>> # This section configures the internal weewx engine. >>> >>> [Engine] >>> >>> # The following section specifies which services should be run and >>> in what order. >>> [[Services]] >>> prep_services = weewx.engine.StdTimeSynch >>> data_services = , >>> process_services = weewx.engine.StdConvert, >>> weewx.engine.StdCalibrate, weewx.engine.StdQC, >>> weewx.wxservices.StdWXCalculate >>> xtype_services = weewx.wxxtypes.StdWXXTypes, >>> weewx.wxxtypes.StdPressureCooker, weewx.wxxtypes.StdRainRater, >>> weewx.wxxtypes.StdDelta >>> archive_services = weewx.engine.StdArchive >>> restful_services = weewx.restx.StdStationRegistry, >>> weewx.restx.StdWunderground, weewx.restx.StdPWSweather, >>> weewx.restx.StdCWOP, weewx.restx.StdWOW, weewx.restx.StdAWEKAS >>> report_services = weewx.engine.StdPrint, weewx.engine.StdReport >>> >>> ####################################### >>> >>> However, I am getting pretty odd results as I cannot see any HTML folder >>> created in /var/www/html/ . >>> >>> As the reporting was the only function I actually needed, this seems >>> rather unfortunate. >>> >>> However, what I have found out is that I cannot see any cheetahgenerator >>> logs at all in the syslog: >>> >>> ####################################### >>> >>> root@server9-weewx:~# tail -n 200 /var/log/syslog |grep 1617 >>> Feb 8 12:02:56 server9-weewx weewx[1617] DEBUG __main__: Initializing >>> engine >>> Feb 8 12:02:56 server9-weewx weewx[1617] INFO weewx.engine: Loading >>> station type Vantage (weewx.drivers.vantage) >>> Feb 8 12:02:56 server9-weewx weewx[1617] DEBUG weewx.drivers.vantage: >>> Driver version is 3.2.3 >>> Feb 8 12:02:56 server9-weewx weewx[1617] DEBUG weewx.drivers.vantage: >>> Option loop_request=1 >>> Feb 8 12:02:56 server9-weewx weewx[1617] DEBUG weewx.drivers.vantage: >>> Opened up ethernet host 192.168.9.2 on port 8080. timeout=5.0, >>> tcp_send_delay=0.5 >>> Feb 8 12:02:56 server9-weewx systemd[1]: weewx.service: Supervising >>> process 1617 which is not our child. We'll most likely not notice when it >>> exits. >>> Feb 8 12:02:56 server9-weewx weewx[1617] DEBUG weewx.drivers.vantage: >>> Gentle wake up of console successful >>> Feb 8 12:02:57 server9-weewx weewx[1617] DEBUG weewx.drivers.vantage: >>> Hardware type is 16 >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.drivers.vantage: >>> ISS ID is 1 >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.drivers.vantage: >>> Hardware name: Vantage Pro2 >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Loading >>> service weewx.engine.StdTimeSynch >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Finished >>> loading service weewx.engine.StdTimeSynch >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Loading >>> service weewx.engine.StdConvert >>> Feb 8 12:03:01 server9-weewx weewx[1617] INFO weewx.engine: StdConvert >>> target unit is 0x1 >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Finished >>> loading service weewx.engine.StdConvert >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Loading >>> service weewx.engine.StdCalibrate >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Finished >>> loading service weewx.engine.StdCalibrate >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Loading >>> service weewx.engine.StdQC >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Finished >>> loading service weewx.engine.StdQC >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Loading >>> service weewx.wxservices.StdWXCalculate >>> Feb 8 12:03:01 server9-weewx weewx[1617] INFO weewx.wxservices: >>> StdWXCalculate will use data binding wx_binding >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.manager: Daily >>> summary version is 4.0 >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Finished >>> loading service weewx.wxservices.StdWXCalculate >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Loading >>> service weewx.wxxtypes.StdWXXTypes >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Finished >>> loading service weewx.wxxtypes.StdWXXTypes >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Loading >>> service weewx.wxxtypes.StdPressureCooker >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Finished >>> loading service weewx.wxxtypes.StdPressureCooker >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Loading >>> service weewx.wxxtypes.StdRainRater >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Finished >>> loading service weewx.wxxtypes.StdRainRater >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Loading >>> service weewx.wxxtypes.StdDelta >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Finished >>> loading service weewx.wxxtypes.StdDelta >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Loading >>> service weewx.engine.StdArchive >>> Feb 8 12:03:01 server9-weewx weewx[1617] INFO weewx.engine: Archive >>> will use data binding wx_binding >>> Feb 8 12:03:01 server9-weewx weewx[1617] INFO weewx.engine: Record >>> generation will be attempted in 'hardware' >>> Feb 8 12:03:01 server9-weewx weewx[1617] INFO weewx.engine: Using >>> archive interval of 1800 seconds (specified by hardware) >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Use LOOP >>> data in hi/low calculations: 1 >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Finished >>> loading service weewx.engine.StdArchive >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Loading >>> service weewx.restx.StdStationRegistry >>> Feb 8 12:03:01 server9-weewx weewx[1617] INFO weewx.restx: >>> StationRegistry: Registration not requested. >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Finished >>> loading service weewx.restx.StdStationRegistry >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Loading >>> service weewx.restx.StdWunderground >>> Feb 8 12:03:01 server9-weewx weewx[1617] INFO weewx.restx: >>> Wunderground: Posting not enabled. >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Finished >>> loading service weewx.restx.StdWunderground >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Loading >>> service weewx.restx.StdPWSweather >>> Feb 8 12:03:01 server9-weewx weewx[1617] INFO weewx.restx: PWSweather: >>> Posting not enabled. >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Finished >>> loading service weewx.restx.StdPWSweather >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Loading >>> service weewx.restx.StdCWOP >>> Feb 8 12:03:01 server9-weewx weewx[1617] INFO weewx.restx: CWOP: >>> Posting not enabled. >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Finished >>> loading service weewx.restx.StdCWOP >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Loading >>> service weewx.restx.StdWOW >>> Feb 8 12:03:01 server9-weewx weewx[1617] INFO weewx.restx: WOW: Posting >>> not enabled. >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Finished >>> loading service weewx.restx.StdWOW >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Loading >>> service weewx.restx.StdAWEKAS >>> Feb 8 12:03:01 server9-weewx weewx[1617] INFO weewx.restx: AWEKAS: >>> Posting not enabled. >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Finished >>> loading service weewx.restx.StdAWEKAS >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Loading >>> service weewx.engine.StdPrint >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Finished >>> loading service weewx.engine.StdPrint >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Loading >>> service weewx.engine.StdReport >>> Feb 8 12:03:01 server9-weewx weewx[1617] INFO weewx.engine: 'pyephem' >>> not detected, extended almanac data is not available >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.engine: Finished >>> loading service weewx.engine.StdReport >>> Feb 8 12:03:01 server9-weewx weewx[1617] INFO __main__: Starting up >>> weewx version 4.6.0 >>> Feb 8 12:03:01 server9-weewx weewx[1617] DEBUG weewx.drivers.vantage: >>> Gentle wake up of console successful >>> Feb 8 12:03:02 server9-weewx weewx[1617] INFO weewx.engine: Clock error >>> is 2.52 seconds (positive is fast) >>> Feb 8 12:03:02 server9-weewx weewx[1617] INFO weewx.engine: Using >>> binding 'wx_binding' to database 'weewx.sdb' >>> Feb 8 12:03:02 server9-weewx weewx[1617] INFO weewx.manager: Starting >>> backfill of daily summaries >>> Feb 8 12:03:02 server9-weewx weewx[1617] INFO weewx.manager: Daily >>> summaries up to date >>> Feb 8 12:03:02 server9-weewx weewx[1617] DEBUG weewx.drivers.vantage: >>> Getting archive packets since 2022-02-08 11:30:00 CET (1644316200) >>> Feb 8 12:03:02 server9-weewx weewx[1617] DEBUG weewx.drivers.vantage: >>> Gentle wake up of console successful >>> Feb 8 12:03:04 server9-weewx weewx[1617] DEBUG weewx.drivers.vantage: >>> Retrieving 1 page(s); starting index= 4 >>> Feb 8 12:03:05 server9-weewx weewx[1617] INFO weewx.manager: Added >>> record 2022-02-08 12:00:00 CET (1644318000) to database 'weewx.sdb' >>> Feb 8 12:03:05 server9-weewx weewx[1617] INFO weewx.manager: Added >>> record 2022-02-08 12:00:00 CET (1644318000) to daily summary in 'weewx.sdb' >>> Feb 8 12:03:05 server9-weewx weewx[1617] INFO weewx.engine: Starting >>> main packet loop. >>> Feb 8 12:03:05 server9-weewx weewx[1617] DEBUG weewx.drivers.vantage: >>> Gentle wake up of console successful >>> Feb 8 12:03:06 server9-weewx weewx[1617] DEBUG weewx.drivers.vantage: >>> Requesting 200 LOOP packets. >>> Feb 8 12:03:06 server9-weewx weewx[1617] DEBUG weewx.drivers.vantage: >>> Gentle wake up of console successful >>> root@server9-weewx:~# >>> >>> ####################################### >>> >>> I have also used this thread to eliminate the read erros and migrated >>> from init.d to systemd (by Peter Fletcher at 14. 3. 2019 21:51:37): >>> https://groups.google.com/g/weewx-user/c/xhZYyX5cg8k >>> >>> This did indeed solve many IP read problems (and I highly recommend to >>> use this instead of init.d in packages). >>> >>> However, the HTMLs are still not generated despite the DB catchup runs >>> correctly. >>> >>> I kindly ask for help. >>> >>> Thank You. >>> >>> Marek Šnapka >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "weewx-user" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/weewx-user/2ad62eeb-94fc-4967-a454-49ac5fe2abaan%40googlegroups.com >>> <https://groups.google.com/d/msgid/weewx-user/2ad62eeb-94fc-4967-a454-49ac5fe2abaan%40googlegroups.com?utm_medium=email&utm_source=footer> >>> . >>> >> -- > You received this message because you are subscribed to the Google Groups > "weewx-user" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/weewx-user/c8e28193-fa7c-4569-bc7d-03bfb72c273an%40googlegroups.com > <https://groups.google.com/d/msgid/weewx-user/c8e28193-fa7c-4569-bc7d-03bfb72c273an%40googlegroups.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/weewx-user/CAPq0zECfErFnovbXabvGXjSronGON3P-6UAh8eOfdTnPz57KiA%40mail.gmail.com.
