You appear to be referring to *Cisco* APs. Thus thread is about *Aruba* APs, 
not Cisco.

It is well known that Cisco tries to keep you trapped in their products. Your 
post is off-topic for the thread.

Bruce Osborne
Wireless Engineer
IT Infrastructure & Media Solutions
 
(434) 592-4229
 
LIBERTY UNIVERSITY
Training Champions for Christ since 1971

-----Original Message-----
From: Frans Panken [mailto:frans.pan...@surfnet.nl] 
Sent: Tuesday, September 15, 2015 2:50 AM
Subject: Re: Aruba Instant IAP-215 Wireless Access Points

We experienced that LLDP does not work properly in the case of non Cisco the 
switches.
We have 3700 APs and Juniper switches. The APs require PoE+ to function with 
all MIMO capabilities (4 spatial streams). The WLC tells us that there is no 
PoE+. With Cisco switches, the WLC does mention that there is PoE+. Even with a 
PoE+ injector of Cisco, the WLC still mentions PoE.
This was when we used 8.0 MR1. Clients could still use 4 spatial streams. We 
were told this was a Cisco bug and the problem would be solved in MR2 (which we 
are not intending to use).
According to the Juniper swith, the APs use less power than you would
expect:

Interface    Admin       Oper    Max        Priority       Power          Class
             status      status  power                     consumption
ge-6/0/15    Enabled      ON     30.0W      Low            4.3W            4
ge-6/0/18    Enabled      ON     30.0W      Low            6.7W            4
ge-6/0/19    Enabled      ON     30.0W      Low            6.1W            4
ge-6/0/20    Enabled      ON     30.0W      Low            6.3W            4
ge-6/0/21    Enabled      ON     30.0W      Low            6.1W            4





Jake Snyder schreef op 15/09/15 om 03:20:
> The other thing you might check is to see if you have LLDP running on the 
> switches.  This can help with Poe negotiation.
>
> Thanks
> Jake Snyder
>
>
> Sent from my iPhone
>
>> On Sep 14, 2015, at 6:53 PM, James Michael Keller <jmkel...@houseofzen.org> 
>> wrote:
>>
>>> On 09/14/2015 11:37 AM, Ronald Loneker wrote:
>>> Good Morning -
>>>
>>> (forgive cross-postings - a member of the NETMAN list suggested this 
>>> might be the place to post this question)
>>>
>>> We just had close to 90 new Aruba Instant IAP-215 wireless access 
>>> points installed in our residence halls to upgrade our wireless network.
>>> Another building is soon to be underway, and I'm managing this project.
>>>
>>> Over the last couple of weeks, it seems like random access points 
>>> are shutting down wireless access.  They are not all connected to 
>>> the same Cisco switch (various Cisco POE switches in two residence 
>>> halls).  The access point is not ping-able, the MAC address is not 
>>> found in the virtual controller's table, the switch port is up and 
>>> power is being supplied to the access point.  The only way we seem 
>>> to get an access point back up is to do a shut/no shut on the switch 
>>> port to which it is connected.
>>>
>>> The vendor who configured the access points hasn't been able to 
>>> determine why this is happening and before we initiate an Aruba 
>>> support call, I was wondering if anyone had any similar experiences 
>>> like this and what you determined was the cause of the issue.  We 
>>> are running into walls here.
>>>
>>> Thanks in advance for any thoughts or ideas.
>>>
>>> Ron Loneker, Jr.
>>> Director of Media Services
>>> College of Saint Elizabeth
>>> Mahoney Library
>>> 2 Convent Road
>>> Morristown, NJ  07960
>>>
>>> Phone:  973-290-4229 <tel:973-290-4229>
>>>
>>> e-mail:  rlone...@cse.edu <mailto:rlone...@cse.edu>
>>>
>>> /**/
>>>
>>>
>>> ********** Participation and subscription information for this 
>>> EDUCAUSE Constituent Group discussion list can be found at 
>>> http://www.educause.edu/groups/.
>> I have seen similar with the campus APs when the PoE power is either 
>> dropping below min spec either due to switch power or cable run
>> resistance.   The APs will have enough power to initialize which brings
>> up the link, but they fail to boot into ArubaOS and hang until they 
>> are power cycled.  Typically the ones with cable run issues continue 
>> to fail on the next cycle.  Brown out triggered ones come up fine 
>> usually, and typically we see more then one on the same switch do it 
>> for PoE power issues.
>>
>> --
>>
>> -James
>>
>>
>> **********
>> Participation and subscription information for this EDUCAUSE Constituent 
>> Group discussion list can be found at http://www.educause.edu/groups/.
>>
> **********
> Participation and subscription information for this EDUCAUSE Constituent 
> Group discussion list can be found at http://www.educause.edu/groups/.

**********
Participation and subscription information for this EDUCAUSE Constituent Group 
discussion list can be found at http://www.educause.edu/groups/.

**********
Participation and subscription information for this EDUCAUSE Constituent Group 
discussion list can be found at http://www.educause.edu/groups/.

Reply via email to