That's not a good idea. You will create multipath interference, which will have an overall negative impact.
On Mon, Feb 1, 2010 at 8:09 PM, Jeremie Chism <jchi...@gmail.com> wrote: > You may have to rotate your cpe to get a lower signal from the tower. > I have one that is pointed at a 45 degree angle away from the tower. > > Sent from my iPhone > > On Feb 1, 2010, at 9:06 PM, RickG <rgunder...@gmail.com> wrote: > > > It's a PtMP environment. I have some customers much further away > > running > > high -70's. > > If I drop the AP side, dont I risk loosing them or affecting their > > throughput? > > What about using an attenuator and padding it down some? > > Thanks! -RickG > > > > On Mon, Feb 1, 2010 at 9:02 PM, Nick Olsen > > <n...@brevardwireless.com> wrote: > > > >> Like we said, Drop both sides till the signal gets in the -55 to > >> -65 range. > >> Doesn't matter what the power is, as long as the signal is around > >> there. As > >> its where your going to get your best throughput, Barring any other > >> interference. > >> > >> Nick Olsen > >> Network Engineer / Customer Support > >> (321) 205-1100 x106 > >> > >> ---------------------------------------- > >> > >> From: "RickG" <rgunder...@gmail.com> > >> Sent: Monday, February 01, 2010 8:56 PM > >> To: "WISPA General List" <wireless@wispa.org> > >> Subject: Re: [WISPA] power > >> > >> Ya, thats what I do. I'm just concerned about what the best power > >> level > >> is? > >> I hate to create a monster based on the wrong settings. > >> > >> On Mon, Feb 1, 2010 at 8:21 PM, Robert West > >> <robert.w...@just-micro.com>wrote: > >> > >>> I have a few like that. Cheap and quick for low density > >>> population. Use > >> a > >>> pac grid for the backhaul and a bullet with an omni for the AP. > >>> Check > >> your > >>> polarity, make sure you're on the right orientation and right > >>> radio. My > >>> grids are horz. Pol and the omnis, well..... Vertical of course! > >>> > >>> Bob- > >>> > >>> > >>> > >>> -----Original Message----- > >>> From: wireless-boun...@wispa.org [mailto:wireless- > >>> boun...@wispa.org] On > >>> Behalf Of RickG > >>> Sent: Monday, February 01, 2010 8:08 PM > >>> To: WISPA General List > >>> Subject: [WISPA] power > >>> > >>> OK, I need a little input. I've got several "poor mans repeaters" > >>> around > >> by > >>> using a pair of bullets, one for backhaul and the other for the AP. > >> Today, > >>> I > >>> installed a Bullet on a new customer that was a stones throw away > >>> from > >> the > >>> AP. At full power, he got just under 1Mbps. Turning down the > >>> power, he > >> got > >>> 3Mbps+. Is turning down the power on the CPE side on a test and > >>> trial > >> basis > >>> or is there some kind of method to it? > >>> -RickG > >>> > >>> > >>> > >>> > >> > >> --- > >> --- > >> --- > >> ------------------------------------------------------------------- > >> > >>> ---- > >>> WISPA Wants You! Join today! > >>> http://signup.wispa.org/ > >>> > >>> > >> > >> --- > >> --- > >> --- > >> ------------------------------------------------------------------- > >> > >>> ---- > >>> > >>> WISPA Wireless List: wireless@wispa.org > >>> > >>> Subscribe/Unsubscribe: > >>> http://lists.wispa.org/mailman/listinfo/wireless > >>> > >>> Archives: http://lists.wispa.org/pipermail/wireless/ > >>> > >>> > >>> > >>> > >>> > >> > >> --- > >> --- > >> --- > >> ------------------------------------------------------------------- > >> ---- > >>> WISPA Wants You! Join today! > >>> http://signup.wispa.org/ > >>> > >>> > >> > >> --- > >> --- > >> --- > >> ------------------------------------------------------------------- > >> ---- > >>> > >>> WISPA Wireless List: wireless@wispa.org > >>> > >>> Subscribe/Unsubscribe: > >>> http://lists.wispa.org/mailman/listinfo/wireless > >>> > >>> Archives: http://lists.wispa.org/pipermail/wireless/ > >>> > >> > >> > >> --- > >> --- > >> --- > >> ------------------------------------------------------------------- > >> ---- > >> WISPA Wants You! Join today! > >> http://signup.wispa.org/ > >> > >> --- > >> --- > >> --- > >> ------------------------------------------------------------------- > >> ---- > >> > >> WISPA Wireless List: wireless@wispa.org > >> > >> Subscribe/Unsubscribe: > >> http://lists.wispa.org/mailman/listinfo/wireless > >> > >> Archives: http://lists.wispa.org/pipermail/wireless/ > >> > >> > >> > >> > >> > >> --- > >> --- > >> --- > >> --- > >> -------------------------------------------------------------------- > >> WISPA Wants You! Join today! > >> http://signup.wispa.org/ > >> > >> --- > >> --- > >> --- > >> --- > >> -------------------------------------------------------------------- > >> > >> WISPA Wireless List: wireless@wispa.org > >> > >> Subscribe/Unsubscribe: > >> http://lists.wispa.org/mailman/listinfo/wireless > >> > >> Archives: http://lists.wispa.org/pipermail/wireless/ > >> > > > > > > --- > > --- > > --- > > --- > > -------------------------------------------------------------------- > > WISPA Wants You! Join today! > > http://signup.wispa.org/ > > --- > > --- > > --- > > --- > > -------------------------------------------------------------------- > > > > WISPA Wireless List: wireless@wispa.org > > > > Subscribe/Unsubscribe: > > http://lists.wispa.org/mailman/listinfo/wireless > > > > Archives: http://lists.wispa.org/pipermail/wireless/ > > > > -------------------------------------------------------------------------------- > WISPA Wants You! Join today! > http://signup.wispa.org/ > > -------------------------------------------------------------------------------- > > WISPA Wireless List: wireless@wispa.org > > Subscribe/Unsubscribe: > http://lists.wispa.org/mailman/listinfo/wireless > > Archives: http://lists.wispa.org/pipermail/wireless/ > -------------------------------------------------------------------------------- WISPA Wants You! Join today! http://signup.wispa.org/ -------------------------------------------------------------------------------- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
