On Fri, 21 Mar 2003, Daniel wrote: > Melisa, > > I get the same problem (missing libglide2x.so) with XFree86 4.2.99.902 > release (essentially 4.3) whilst trying to get my Radion 9000 pro to run > in X under Linux Mandrake 9.0. How did you solve this? > -Did you get create the soft link with the libglide3x.so rather than > libglide2x.so
>>no, as I was informed the libglide3x.so was used only with 3Dfx cards >>(Note: i have no idea why the message appeared -- on reboot it did not >>show up again). Do you still get that message? Were you able to make >>Xconfig recognize your card? Did you get your driver from ATI (I don't >>remember what u said)? > I have to admit, I haven't attempted to start X since getting the message (missing libglide2x.so) when I run Xfree86 -configure. I guess I assumed the worst and didn't bother. Assuming the XF8Config.new looks ok then I will try this tomorrow. The drivers from ATI didn't work (I'm not alone in experiencing how ineffectual they are!) 1) attempted to install the 4.2.X ATI drivers found athttp://www.ati.com/support/drivers/linux/radeon-linux.html?cboOS=Linux XFree86&cboProducts=RADEON+9000&eula=&choice=agree&cm however, when I login as root and try: 2) $>rpm -i <name of file for x server 4.2.x> : yields no ouptut, so do I assume everything is ok 3) $>rpm -q <name of file for x server 4.2.x> :tells me the package is not installed 4) $>rpm -qpl <name of file for x server4 .2.x> : yields no output 5) Also I also can't seem to find where "fglrxconfig" is meant to be installed let alone run it! >>Note: I have read a number of posts on ATI chips...most particularly the >>Radeon 9000. Perhaps messaging one of those people who answered queries on >>that type card (they tend to know one manufacturer well) would attract >>attention? Do you keep these posts? (try [EMAIL PROTECTED] -- I sent >>you one of his posts that mentioned Radeon's 9000) thanks for sending me the email from Danian - that too looks promising > -Did you have to edit the XF86config to take account of this change (I > have created mine with XFree86 - configure) > >>My Xconfig would not work until I reduced the refresh rate to 60, the >>color bit to 8 and selected VESA...way bad, but was able to at least >>increase the resolution to over 800x600! Hmmmm sounds a bit worrying; I will bear this in mind >>VSince I am not content (I got better results with the XFree86 version >>that >>came with RH7.3 -- I only went to XFree86 ver4.3 as it promised SiS300 >>support which wasn't happening under the RH7.3 version (I forget which >>version that is)), I am gonna try to go to RH8.0 and be content till I can >>buy a new card... ;P > > I'm beginning to see why Windows XP (which happily coexists with my > 9000) is so popular! > > Without XP we wouldn't be able to exchange these e-mails! I like Linux (as it is similar to the Solaris I use at work) but I would want to be totally reliant on it! So to end I will give some of your suggestions a go in a structured fashion and see what works best Good night Daniel >>Yes, I understand that a bit! I do dual boot with Win2K still as evidently >>I too am far away from being ready/able to changeover;[ ! >>Sorry I can't help you more...I keep checking all the posts and reading >>elsewhere in hopes to find something that might put some light on this >>subject. If I read anything (more), or get help from the Xconfig >>people (before or after the upgrade), I will try to pass it on. mgolter > > > Regards > > > Daniel > > > > >The linux and XFree4 install was so I can run some 3D > applications...but I > >did not know that glide was so specifically aimed...the Real problem > was > >that I couldn't get the X server configured at all. Right now I am > >stuck with 16 bit color...(using generic VESA in Xconfigurator, which > is > >not as good as what I could get with the XFree86 version that came with > >RH7.3! > > >{I installed the 4.3 version as no other version even lists the SiS300 > >chip...and it looks like 4.3 doesn't really support it either...) > > >Thanks for info on the .so (so's I am not a gonna worry (esp since no > >system complaints!) > > ;) > > mgolter > > > > On Fri, 14 Mar 2003, Mike A. Harris wrote: > > > On Fri, 14 Mar 2003, Melissa Golter wrote: > > > > >Date: Fri, 14 Mar 2003 14:57:34 -0600 (CST) > > >From: Melissa Golter <[EMAIL PROTECTED]> > > >To: "'[EMAIL PROTECTED]'" <[EMAIL PROTECTED]> > > >Cc: [EMAIL PROTECTED] > > >Reply-To: [EMAIL PROTECTED] > > >Content-Type: TEXT/PLAIN; charset=US-ASCII > > >Subject: RE: Sis300 support in XFree86 version 4.3.0 > > > > > >If I am reading the filename correctly, that file is 26Mb -- but if > that > > >is OK to > > >send to you, will do...in the meantime, I put it in > > >ftp.evl.uic.edu/pub/INcoming/mgolter/xfree/ > > > > > >btw, ver 4.3.0 has libglide3.so but not the 2x.so nec to configure > the > > >system correctly. I am supposing I can find the libglide2x.so > somewhere > > >(note: the previous version of XFree86 -- the one that came with > RH7.3, > > >did not include it either it seems (a *whereis* did not yield a > result > > >from the saved XFree version directory either). ;P > > > > Just so you don't end up wasting your time.... > > > > Glide is strictly a 3Dfx low level 3D video driver library which > > talks directly to 3Dfx Voodoo and Banshee video hardware. > > > > Glide 2 is for Voodoo Graphics I/II hardware, and Glide3 is for > > Voodoo 3/4/5 and Banshee hardware. > > > > Glide does not work on any other video hardware, and is totally > > useless unless you have 3Dfx video hardware, in which case it > > provides the layer between DRI and the 3Dfx video card for 3D > > acceleration. > > > > In short: You've got an SiS video card, and Glide is meaningless > > as far as your system is concerned. > > > > -- > > Mike A. Harris > > > > > > _______________________________________________ > > XFree86 mailing list > > [EMAIL PROTECTED] > > http://XFree86.Org/mailman/listinfo/xfree86 > > > Radion 9000 Pro ML9.0 and the m > _______________________________________________ XFree86 mailing list [EMAIL PROTECTED] http://XFree86.Org/mailman/listinfo/xfree86

