Hi Jason, coming late into this thread,
Jason Bradfield wrote:
Thanks Jeff.
FYI, These zones will be allocated to different clients each with root
access to their zone and running their own software.
Whether you choose to provide root access to the non-global zone users
has no effect on the ability to set the limits via zonecfg in Nevada and
the next update of Solaris 10. They will not be able to increase the cap
from within the non-global zone. (This is not the case with S10 11/06 and
prior, where rcapd runs per zone. A user with sufficient privileges in the
zone could change the cap.)
What we really want and are waiting for is dedicated memory, not capping..
Your workload characteristics and service delivery constraints may be best
served with dedicated memory, and it is independent of whether the zones'
users have root access.
Steffen
Do you know when this will be coming, and will this also include prstat,
df, swap etc only displaying the allocated Memory..
Jeff Victor wrote:
Jason Bradfield wrote:
Sorry if this comes through as a duplicate response but I responded
from a different email account earlier...
Thanks Bob and Jeff...
Therefore here is my confusion..
From Bob
* swap: the amount of disk space set aside to copy physical memory to
when copying it out of RAM
From Jeff
set swap= this is VM - the total address space available to the
zone
Ok.. to solve my immediate problem 16GB Physical and 16GB disk =
total of 32GB Virtual
If I were to create 3 zones and wanted to evenly allocate memory to
all 3 and the global zone, would this config be ok
zonecfg:host30> add capped-memory
zonecfg:host30:capped-memory> set physical=4G
zonecfg:host30:capped-memory> set swap=8G
zonecfg:host30:capped-memory> end
Memory capping isn't really intended to solve the 'problem' of
allocating memory, because usually there isn't a problem. Memory
capping is intended to prevent memory hogs (accidental or otherwise)
from impacting proper operation of other workloads. This allows you
to choose large caps, improving resource usage efficiency.
With some v12n solutions, allocating memory is required. This has the
potential of wasting memory - if one virtual server is not using all
of its memory, another cannot.
With zones, memory allocation (and its wastefulness) is not necessary.
Further, choosing a physical memory cap that is too low will result in
unnecessary paging activity, which will significantly reduce
performance on that one zone, and also affect performance of other
zones, to some extent.
However, if you want to ensure that one zone does not use too much and
impact other zones, measure (or estimate) its normal memory usage, and
choose a value larger than that. After the zone is running, "prstat
-Z" can be used to measure memory usage, both physical and swap.
With all of that in mind, in your situation I would choose much larger
numbers than the ones shown above. But without understanding the
normal resource consumption of your workloads, I can't guess at good
values.
Finally, it usually helps to know that those caps can be changed while
the zone is running, using rcapadm from the global zone.
Thanks.
Bob Bownes wrote:
>> Can anyone, in lamens (ex linux) terms explain the differences
between
>> virtual/swap/rss/size/physical etc or recomend a good
>> blog/article/document.
>
>I don't know Linux terms, so I'll define terms for this conversation:
>* physical memory: RAM, memory chips
>* VM (virtual memory): the total memory space available, both in
RAM and
> on disk
>
I'll add:
* swap: the amount of disk space set aside to copy physical memory
to when copying it out of RAM
* rss: Resident Set Size - the part of a process address space which
is currently resident in RAM
* size: The total address space used by a process
* physical - various definitions, most common one i've seen is the
total amount of RAM in the system. Also refered to as 'real' in some
places
And a link I found that might be of some use:
http://www.memorymanagement.org/
>The terms in zonecfg are:
>* set physical= this is what I am calling "physical memory"
>* set swap= this is VM - the total address space available to
the zone
>
>So if you want to limit the zone's processes to 384MB of VM and
128MB of RAM, use:
>
>add capped-memory
>set physical=128m
>set swap=384m
>end
>If you already have added these, you must use "select
capped-memory" instead
>of "add capped-memory".
>
>
>Does that help?
_______________________________________________
zones-discuss mailing list
zones-discuss@opensolaris.org
_______________________________________________
zones-discuss mailing list
zones-discuss@opensolaris.org
