I would like to state a glitch that happens once in a great while on my P3. It will stay on while transmitting and I see my transmitted signal. If it is a glitch, it must be a SW one because the display hardware is doing its job. Then one would suggest it could be toggled on and off???? What a wonderful thought.... hint hint.....
Mel, K6KBE ________________________________ From: Gary Gregory <vk1zzg...@gmail.com> To: Sam Morgan <k5oai....@gmail.com> Cc: "elecraft@mailman.qth.net" <elecraft@mailman.qth.net> Sent: Tuesday, September 24, 2013 8:06 AM Subject: Re: [Elecraft] P3 Feature Request - Transmit sampling Sam, I still believe in the ol saying...the squeeky wheel get's the oil...so it's good to keep our requests up. 73 On 25 September 2013 01:03, Sam Morgan <k5oai....@gmail.com> wrote: > I know we aren't suppose to do the 'me to' kind of posts here > and before hundreds of others add theirs and the topic gets canned > (again)... > > as far as I am concerned this is the only remaining 'feature' that ruins > an otherwise perfect station combo. > > perhaps the Flex is worth looking at again if this is never going to be > addressed?? > > > On 9/24/2013 9:11 AM, Gary Gregory wrote: > >> Your not alone...:-( >> >> >> On 25 September 2013 00:09, Bob <wb4...@gmail.com> wrote: >> >> So I've been loving my P3 for about 2 years now, and I keep looking at >>> that >>> lonely sensor window in the back, dreaming and wishing.... >>> >>> Yesterday I received an email from a ham a few thousand miles away asking >>> me to clean up my signal -- I was running JT65 at the time, and he saw my >>> signal decode on his rig in a half-dozen spots across the waterfall. I >>> panicked, of course, and immediately checked everything -- Line Level was >>> four bars steady with an occasional fifth bar flickering, transmit power >>> was 5.0 watts, monitor was sounding perfectly fine, and my handheld >>> receiver was sounding OK too. Later that night a nearby ham was nice >>> enough to run a spectral analysis on my signal and found it looked clean >>> as >>> well. >>> >>> Imagine how easy it would be for me to verify my outbound signal quality >>> if >>> my P3 had an outboard RF sampling tap that communicated via IR back to >>> the >>> P3 and allows the outbound RF to be displayed. >>> >>> One can dream and wish. >>> >>> 73, Bob, WB4SON >>> >> > > -- > > GB & 73 > K5OAI > Sam Morgan > > ______________________________**______________________________**__ > Elecraft mailing list > Home: > http://mailman.qth.net/**mailman/listinfo/elecraft<http://mailman.qth.net/mailman/listinfo/elecraft> > Help: http://mailman.qth.net/mmfaq.**htm<http://mailman.qth.net/mmfaq.htm> > Post: mailto:elecr...@mailman.qth.**net <Elecraft@mailman.qth.net> > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > -- *Gary - VK1ZZ Skype: Gary.VK1ZZ http://www.qsl.net/vk1zz Motorhome Portable* *"Grumpy's House"* *Elecraft K3 KPA500FT KAT500FT** * ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
