If you disconnect the RS232 cable between the P3 and the K3, the P3 display
stays on during tx and shows the tx signal. I haven't tried it in digital
modes but it certainly works for CW and SSB. It's a good workaround that has
been mentioned on this reflector in the past.
73 to all
Geoff
G3UCK
-----Original Message-----
From: Mel Farrer
Sent: Tuesday, September 24, 2013 8:49 PM
To: Gary Gregory ; Sam Morgan
Cc: elecraft@mailman.qth.net
Subject: Re: [Elecraft] P3 Feature Request - Transmit sampling
I would like to state a glitch that happens once in a great while on my P3.
It will stay on while transmitting and I see my transmitted signal. If it
is a glitch, it must be a SW one because the display hardware is doing its
job. Then one would suggest it could be toggled on and off???? What a
wonderful thought.... hint hint.....
Mel, K6KBE
________________________________
From: Gary Gregory <vk1zzg...@gmail.com>
To: Sam Morgan <k5oai....@gmail.com>
Cc: "elecraft@mailman.qth.net" <elecraft@mailman.qth.net>
Sent: Tuesday, September 24, 2013 8:06 AM
Subject: Re: [Elecraft] P3 Feature Request - Transmit sampling
Sam,
I still believe in the ol saying...the squeeky wheel get's the oil...so
it's good to keep our requests up.
73
On 25 September 2013 01:03, Sam Morgan <k5oai....@gmail.com> wrote:
I know we aren't suppose to do the 'me to' kind of posts here
and before hundreds of others add theirs and the topic gets canned
(again)...
as far as I am concerned this is the only remaining 'feature' that ruins
an otherwise perfect station combo.
perhaps the Flex is worth looking at again if this is never going to be
addressed??
On 9/24/2013 9:11 AM, Gary Gregory wrote:
Your not alone...:-(
On 25 September 2013 00:09, Bob <wb4...@gmail.com> wrote:
So I've been loving my P3 for about 2 years now, and I keep looking at
that
lonely sensor window in the back, dreaming and wishing....
Yesterday I received an email from a ham a few thousand miles away
asking
me to clean up my signal -- I was running JT65 at the time, and he saw
my
signal decode on his rig in a half-dozen spots across the waterfall. I
panicked, of course, and immediately checked everything -- Line Level
was
four bars steady with an occasional fifth bar flickering, transmit power
was 5.0 watts, monitor was sounding perfectly fine, and my handheld
receiver was sounding OK too. Later that night a nearby ham was nice
enough to run a spectral analysis on my signal and found it looked clean
as
well.
Imagine how easy it would be for me to verify my outbound signal quality
if
my P3 had an outboard RF sampling tap that communicated via IR back to
the
P3 and allows the outbound RF to be displayed.
One can dream and wish.
73, Bob, WB4SON
--
GB & 73
K5OAI
Sam Morgan
______________________________**______________________________**__
Elecraft mailing list
Home:
http://mailman.qth.net/**mailman/listinfo/elecraft<http://mailman.qth.net/mailman/listinfo/elecraft>
Help: http://mailman.qth.net/mmfaq.**htm<http://mailman.qth.net/mmfaq.htm>
Post: mailto:elecr...@mailman.qth.**net <Elecraft@mailman.qth.net>
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
--
*Gary - VK1ZZ
Skype: Gary.VK1ZZ
http://www.qsl.net/vk1zz
Motorhome Portable*
*"Grumpy's House"*
*Elecraft K3
KPA500FT
KAT500FT**
*
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
