Re: [Elphel-support] Elphel 393 Nand upgrade
Hello Mohamed, Internal secondary power supplies (that generate 1.0V, 1.5V, 1.8V) on the 10393 board are constantly monitored and shut down if any of them drops below threshold. When 5.0V is turned on, even with no load it charges capacitors and it causes extra load on the primary 3.3V, so either 3.3V itself or one of the secondary ones for the short time drops below the limit. It is possible to modify the driver to temporarily disable power fault detection, turn 5V on and then re-enable detection. But as your camera works with 10385 and power extra load for turning 5V is small makes me suspect that there is a problem with 3V power source - it is close to the lower limit, or the wires are long, or smth. else. So the camera can reset itself at later stages (turning on streaming, or recording to SSD or anything else. Andrey On Thu, 13 Dec 2018 13:24:41 -0800 Mohamed Morsy wrote I replaced it with the 10385 board and now it works. Thanks. On Thu, Dec 13, 2018 at 4:21 PM Mohamed Morsy wrote: There are no sensors connected. I'm using direct 3.3V from a power supply. I can try the 10385 board. On Thu, Dec 13, 2018 at 4:19 PM Oleg wrote: This happens when the board tries to turn on 5V and fails. Try: * disconnect sensors if any connected * another power supply (how do you power the board? direct 3.3V or 48V via 10385 board?) * another power cable On Thu, Dec 13, 2018 at 1:50 PM Mohamed Morsy wrote: No it does not boot from flash. The card does work with other boards. On Thu, Dec 13, 2018 at 3:46 PM Oleg wrote: Hi Mohamed, Does the board boot fine from flash? Does the same uSD card work with other rev B boards? On Thu, Dec 13, 2018 at 1:30 PM Mohamed Morsy wrote: Hi Oleg, I'm having another issue with another Elphel. It doesn't seem to boot up completely. When I connect the USB cable, open minicom, and power on the Elphel, it starts booting up for 2 seconds then stops and minicom says "Cannot open /dev/ttyUSB0!" The last thing on minicom before it stops is: [ 2.034545] elphel393-pwr elphel393-pwr@0: Probing elphel393-pwr This is a Rev B Elphel running on a uSD card. Do you know what the issue might be? Thanks, Mohamed On Wed, Dec 5, 2018 at 9:48 AM Mohamed Morsy wrote: That worked. Thanks. Mohamed On Tue, Dec 4, 2018 at 5:30 PM Oleg wrote: Wrong file. My bad. Try this one. On Tue, Dec 4, 2018 at 3:17 PM Morsy, Mohamed K wrote: Hi Oleg, I tried replacing the devicetree.dtb file in the nand folder from elphel393_20180511 with the one you sent. I tried the ipaddress/update_software.html tool again but nothing changed. When I log into the elphel from minicom and try ifconfig I still only get the local address at 127.0.0.1. This is on a Rev C board. Do you have any other ideas? Also I meant to send the previous email from my Redzone email so I'll CC myself to this chain. Thanks, Mohamed Morsy From: Oleg Sent: Tuesday, December 4, 2018 2:51 PM To: Morsy, Mohamed K Cc: elphel support-list Subject: Re: [Elphel-support] Elphel 393 Nand upgrade Hi Mohamed, I think it's not related. Most likely you need an updated device tree (devicetree.dtb). The newest boards are revC - they have a different PHY reg address compared to revB (and older). The recovery cards came with updated devicetree - and so, the network is working. The revision letter is printed near the network connector on top of the board. For revC - try devicetree.dtb from the attachment. fix_net_config.tar.gz - just moves network configuration from /etc/elphel393/init_elphel393.py to /etc/network/interfaces which is a more conventional place for linux. And it will be included in the next release. I'm having trouble upgrading the NAND memory on an elphel 393. I've tried it with multiple boards. I used the ipaddress/update_software.html tool. When I flash the board, I shut it down, remove the uSD card, and reboot it. But it doesn't boot up correctly. I'm able to log in on minicom but when I try ifconfig I find that the board doesn't have an ip address. Do you know how to resolve this issue? I noticed there's a recent upload at community.elphel.com/files/393 called fix_net_config.tar.gz. Is that related to my issue? Thanks, Mohamed Morsy RedZone Robotics ___ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com ___ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com Best regards, Oleg Dzhimiev Electronics Engineer phone: +1 801 783 x124 Elphel, Inc. ___ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com ___ Support-list mailing list Su
Re: [Elphel-support] Elphel 393 Nand upgrade
Alright, so it's some marginal 3.3V. If you need 3.3V - try replacing the wires or the power supply. On Thu, Dec 13, 2018 at 2:26 PM Mohamed Morsy wrote: > I replaced it with the 10385 board and now it works. Thanks. > > On Thu, Dec 13, 2018 at 4:21 PM Mohamed Morsy wrote: > >> There are no sensors connected. I'm using direct 3.3V from a power >> supply. I can try the 10385 board. >> >> On Thu, Dec 13, 2018 at 4:19 PM Oleg >> wrote: >> >>> This happens when the board tries to turn on 5V and fails. >>> >>> Try: >>> * disconnect sensors if any connected >>> * another power supply (how do you power the board? direct 3.3V or 48V >>> via 10385 board?) >>> * another power cable >>> >>> On Thu, Dec 13, 2018 at 1:50 PM Mohamed Morsy >>> wrote: >>> >>>> No it does not boot from flash. >>>> The card does work with other boards. >>>> >>>> On Thu, Dec 13, 2018 at 3:46 PM Oleg >>>> wrote: >>>> >>>>> Hi Mohamed, >>>>> >>>>> Does the board boot fine from flash? >>>>> Does the same uSD card work with other rev B boards? >>>>> >>>>> On Thu, Dec 13, 2018 at 1:30 PM Mohamed Morsy >>>>> wrote: >>>>> >>>>>> Hi Oleg, >>>>>> >>>>>> I'm having another issue with another Elphel. It doesn't seem to boot >>>>>> up completely. When I connect the USB cable, open minicom, and power on >>>>>> the >>>>>> Elphel, it starts booting up for 2 seconds then stops and minicom says >>>>>> "Cannot open /dev/ttyUSB0!" The last thing on minicom before it stops is: >>>>>> >>>>>> [2.034545] elphel393-pwr elphel393-pwr@0: Probing elphel393-pwr >>>>>> >>>>>> This is a Rev B Elphel running on a uSD card. Do you know what the >>>>>> issue might be? >>>>>> >>>>>> Thanks, >>>>>> >>>>>> Mohamed >>>>>> >>>>>> On Wed, Dec 5, 2018 at 9:48 AM Mohamed Morsy >>>>>> wrote: >>>>>> >>>>>>> That worked. Thanks. >>>>>>> >>>>>>> Mohamed >>>>>>> >>>>>>> On Tue, Dec 4, 2018 at 5:30 PM Oleg >>>>>>> wrote: >>>>>>> >>>>>>>> Wrong file. My bad. Try this one. >>>>>>>> >>>>>>>> On Tue, Dec 4, 2018 at 3:17 PM Morsy, Mohamed K >>>>>>>> wrote: >>>>>>>> >>>>>>>>> Hi Oleg, >>>>>>>>> >>>>>>>>> >>>>>>>>> I tried replacing the devicetree.dtb file in the nand folder from >>>>>>>>> elphel393_20180511 >>>>>>>>> with the one you sent. I tried the ipaddress/update_software.html >>>>>>>>> tool again but nothing changed. When I log into the elphel from >>>>>>>>> minicom and >>>>>>>>> try ifconfig I still only get the local address at 127.0.0.1. This is >>>>>>>>> on a >>>>>>>>> Rev C board. Do you have any other ideas? >>>>>>>>> >>>>>>>>> >>>>>>>>> Also I meant to send the previous email from my Redzone email so >>>>>>>>> I'll CC myself to this chain. >>>>>>>>> >>>>>>>>> >>>>>>>>> Thanks, >>>>>>>>> >>>>>>>>> >>>>>>>>> Mohamed Morsy >>>>>>>>> >>>>>>>>> >>>>>>>>> -- >>>>>>>>> *From:* Oleg >>>>>>>>> *Sent:* Tuesday, December 4, 2018 2:51 PM >>>>>>>>> *To:* Morsy, Mohamed K >>>>>>>>> *Cc:* elphel support-list >>>>>>>>> *Subject:* Re: [Elphel-support] Elphel 393 Nand upgrade >>>>>>>>> >>>>>>>>> Hi Mohamed, >>>>>>>>> >>>>>>>>> I think it's not related. >>>>>>>>> >>>>>>>
Re: [Elphel-support] Elphel 393 Nand upgrade
This happens when the board tries to turn on 5V and fails. Try: * disconnect sensors if any connected * another power supply (how do you power the board? direct 3.3V or 48V via 10385 board?) * another power cable On Thu, Dec 13, 2018 at 1:50 PM Mohamed Morsy wrote: > No it does not boot from flash. > The card does work with other boards. > > On Thu, Dec 13, 2018 at 3:46 PM Oleg > wrote: > >> Hi Mohamed, >> >> Does the board boot fine from flash? >> Does the same uSD card work with other rev B boards? >> >> On Thu, Dec 13, 2018 at 1:30 PM Mohamed Morsy wrote: >> >>> Hi Oleg, >>> >>> I'm having another issue with another Elphel. It doesn't seem to boot up >>> completely. When I connect the USB cable, open minicom, and power on the >>> Elphel, it starts booting up for 2 seconds then stops and minicom says >>> "Cannot open /dev/ttyUSB0!" The last thing on minicom before it stops is: >>> >>> [2.034545] elphel393-pwr elphel393-pwr@0: Probing elphel393-pwr >>> >>> This is a Rev B Elphel running on a uSD card. Do you know what the issue >>> might be? >>> >>> Thanks, >>> >>> Mohamed >>> >>> On Wed, Dec 5, 2018 at 9:48 AM Mohamed Morsy wrote: >>> >>>> That worked. Thanks. >>>> >>>> Mohamed >>>> >>>> On Tue, Dec 4, 2018 at 5:30 PM Oleg >>>> wrote: >>>> >>>>> Wrong file. My bad. Try this one. >>>>> >>>>> On Tue, Dec 4, 2018 at 3:17 PM Morsy, Mohamed K >>>>> wrote: >>>>> >>>>>> Hi Oleg, >>>>>> >>>>>> >>>>>> I tried replacing the devicetree.dtb file in the nand folder from >>>>>> elphel393_20180511 >>>>>> with the one you sent. I tried the ipaddress/update_software.html >>>>>> tool again but nothing changed. When I log into the elphel from minicom >>>>>> and >>>>>> try ifconfig I still only get the local address at 127.0.0.1. This is on >>>>>> a >>>>>> Rev C board. Do you have any other ideas? >>>>>> >>>>>> >>>>>> Also I meant to send the previous email from my Redzone email so I'll >>>>>> CC myself to this chain. >>>>>> >>>>>> >>>>>> Thanks, >>>>>> >>>>>> >>>>>> Mohamed Morsy >>>>>> >>>>>> >>>>>> -- >>>>>> *From:* Oleg >>>>>> *Sent:* Tuesday, December 4, 2018 2:51 PM >>>>>> *To:* Morsy, Mohamed K >>>>>> *Cc:* elphel support-list >>>>>> *Subject:* Re: [Elphel-support] Elphel 393 Nand upgrade >>>>>> >>>>>> Hi Mohamed, >>>>>> >>>>>> I think it's not related. >>>>>> >>>>>> Most likely you need an updated device tree (devicetree.dtb). The >>>>>> newest boards are revC - they have a different PHY reg address compared >>>>>> to >>>>>> revB (and older). The recovery cards came with updated devicetree - and >>>>>> so, >>>>>> the network is working. >>>>>> The revision letter is printed near the network connector on top of >>>>>> the board. For revC - try devicetree.dtb from the attachment. >>>>>> >>>>>> fix_net_config.tar.gz - just moves network configuration from >>>>>> /etc/elphel393/init_elphel393.py to /etc/network/interfaces which is a >>>>>> more >>>>>> conventional place for linux. And it will be included in the next >>>>>> release. >>>>>> >>>>>> I'm having trouble upgrading the NAND memory on an elphel 393. I've >>>>>> tried it with multiple boards. I used the ipaddress/update_software.html >>>>>> tool. When I flash the board, I shut it down, remove the uSD card, and >>>>>> reboot it. But it doesn't boot up correctly. I'm able to log in on >>>>>> minicom >>>>>> but when I try ifconfig I find that the board doesn't have an ip address. >>>>>> Do you know how to resolve this issue? I noticed there's a recent upload >>>>>> at >>>>>> community.elphel.com/files/393 &
Re: [Elphel-support] Elphel 393 Nand upgrade
I replaced it with the 10385 board and now it works. Thanks. On Thu, Dec 13, 2018 at 4:21 PM Mohamed Morsy wrote: > There are no sensors connected. I'm using direct 3.3V from a power supply. > I can try the 10385 board. > > On Thu, Dec 13, 2018 at 4:19 PM Oleg > wrote: > >> This happens when the board tries to turn on 5V and fails. >> >> Try: >> * disconnect sensors if any connected >> * another power supply (how do you power the board? direct 3.3V or 48V >> via 10385 board?) >> * another power cable >> >> On Thu, Dec 13, 2018 at 1:50 PM Mohamed Morsy wrote: >> >>> No it does not boot from flash. >>> The card does work with other boards. >>> >>> On Thu, Dec 13, 2018 at 3:46 PM Oleg >>> wrote: >>> >>>> Hi Mohamed, >>>> >>>> Does the board boot fine from flash? >>>> Does the same uSD card work with other rev B boards? >>>> >>>> On Thu, Dec 13, 2018 at 1:30 PM Mohamed Morsy >>>> wrote: >>>> >>>>> Hi Oleg, >>>>> >>>>> I'm having another issue with another Elphel. It doesn't seem to boot >>>>> up completely. When I connect the USB cable, open minicom, and power on >>>>> the >>>>> Elphel, it starts booting up for 2 seconds then stops and minicom says >>>>> "Cannot open /dev/ttyUSB0!" The last thing on minicom before it stops is: >>>>> >>>>> [2.034545] elphel393-pwr elphel393-pwr@0: Probing elphel393-pwr >>>>> >>>>> This is a Rev B Elphel running on a uSD card. Do you know what the >>>>> issue might be? >>>>> >>>>> Thanks, >>>>> >>>>> Mohamed >>>>> >>>>> On Wed, Dec 5, 2018 at 9:48 AM Mohamed Morsy >>>>> wrote: >>>>> >>>>>> That worked. Thanks. >>>>>> >>>>>> Mohamed >>>>>> >>>>>> On Tue, Dec 4, 2018 at 5:30 PM Oleg >>>>>> wrote: >>>>>> >>>>>>> Wrong file. My bad. Try this one. >>>>>>> >>>>>>> On Tue, Dec 4, 2018 at 3:17 PM Morsy, Mohamed K >>>>>>> wrote: >>>>>>> >>>>>>>> Hi Oleg, >>>>>>>> >>>>>>>> >>>>>>>> I tried replacing the devicetree.dtb file in the nand folder from >>>>>>>> elphel393_20180511 >>>>>>>> with the one you sent. I tried the ipaddress/update_software.html >>>>>>>> tool again but nothing changed. When I log into the elphel from >>>>>>>> minicom and >>>>>>>> try ifconfig I still only get the local address at 127.0.0.1. This is >>>>>>>> on a >>>>>>>> Rev C board. Do you have any other ideas? >>>>>>>> >>>>>>>> >>>>>>>> Also I meant to send the previous email from my Redzone email so >>>>>>>> I'll CC myself to this chain. >>>>>>>> >>>>>>>> >>>>>>>> Thanks, >>>>>>>> >>>>>>>> >>>>>>>> Mohamed Morsy >>>>>>>> >>>>>>>> >>>>>>>> -- >>>>>>>> *From:* Oleg >>>>>>>> *Sent:* Tuesday, December 4, 2018 2:51 PM >>>>>>>> *To:* Morsy, Mohamed K >>>>>>>> *Cc:* elphel support-list >>>>>>>> *Subject:* Re: [Elphel-support] Elphel 393 Nand upgrade >>>>>>>> >>>>>>>> Hi Mohamed, >>>>>>>> >>>>>>>> I think it's not related. >>>>>>>> >>>>>>>> Most likely you need an updated device tree (devicetree.dtb). The >>>>>>>> newest boards are revC - they have a different PHY reg address >>>>>>>> compared to >>>>>>>> revB (and older). The recovery cards came with updated devicetree - >>>>>>>> and so, >>>>>>>> the network is working. >>>>>>>> The revision letter is printed near the network connector on top of >>>>>>>> the b
Re: [Elphel-support] Elphel 393 Nand upgrade
There are no sensors connected. I'm using direct 3.3V from a power supply. I can try the 10385 board. On Thu, Dec 13, 2018 at 4:19 PM Oleg wrote: > This happens when the board tries to turn on 5V and fails. > > Try: > * disconnect sensors if any connected > * another power supply (how do you power the board? direct 3.3V or 48V via > 10385 board?) > * another power cable > > On Thu, Dec 13, 2018 at 1:50 PM Mohamed Morsy wrote: > >> No it does not boot from flash. >> The card does work with other boards. >> >> On Thu, Dec 13, 2018 at 3:46 PM Oleg >> wrote: >> >>> Hi Mohamed, >>> >>> Does the board boot fine from flash? >>> Does the same uSD card work with other rev B boards? >>> >>> On Thu, Dec 13, 2018 at 1:30 PM Mohamed Morsy >>> wrote: >>> >>>> Hi Oleg, >>>> >>>> I'm having another issue with another Elphel. It doesn't seem to boot >>>> up completely. When I connect the USB cable, open minicom, and power on the >>>> Elphel, it starts booting up for 2 seconds then stops and minicom says >>>> "Cannot open /dev/ttyUSB0!" The last thing on minicom before it stops is: >>>> >>>> [2.034545] elphel393-pwr elphel393-pwr@0: Probing elphel393-pwr >>>> >>>> This is a Rev B Elphel running on a uSD card. Do you know what the >>>> issue might be? >>>> >>>> Thanks, >>>> >>>> Mohamed >>>> >>>> On Wed, Dec 5, 2018 at 9:48 AM Mohamed Morsy >>>> wrote: >>>> >>>>> That worked. Thanks. >>>>> >>>>> Mohamed >>>>> >>>>> On Tue, Dec 4, 2018 at 5:30 PM Oleg >>>>> wrote: >>>>> >>>>>> Wrong file. My bad. Try this one. >>>>>> >>>>>> On Tue, Dec 4, 2018 at 3:17 PM Morsy, Mohamed K >>>>>> wrote: >>>>>> >>>>>>> Hi Oleg, >>>>>>> >>>>>>> >>>>>>> I tried replacing the devicetree.dtb file in the nand folder from >>>>>>> elphel393_20180511 >>>>>>> with the one you sent. I tried the ipaddress/update_software.html >>>>>>> tool again but nothing changed. When I log into the elphel from minicom >>>>>>> and >>>>>>> try ifconfig I still only get the local address at 127.0.0.1. This is >>>>>>> on a >>>>>>> Rev C board. Do you have any other ideas? >>>>>>> >>>>>>> >>>>>>> Also I meant to send the previous email from my Redzone email so >>>>>>> I'll CC myself to this chain. >>>>>>> >>>>>>> >>>>>>> Thanks, >>>>>>> >>>>>>> >>>>>>> Mohamed Morsy >>>>>>> >>>>>>> >>>>>>> -- >>>>>>> *From:* Oleg >>>>>>> *Sent:* Tuesday, December 4, 2018 2:51 PM >>>>>>> *To:* Morsy, Mohamed K >>>>>>> *Cc:* elphel support-list >>>>>>> *Subject:* Re: [Elphel-support] Elphel 393 Nand upgrade >>>>>>> >>>>>>> Hi Mohamed, >>>>>>> >>>>>>> I think it's not related. >>>>>>> >>>>>>> Most likely you need an updated device tree (devicetree.dtb). The >>>>>>> newest boards are revC - they have a different PHY reg address compared >>>>>>> to >>>>>>> revB (and older). The recovery cards came with updated devicetree - and >>>>>>> so, >>>>>>> the network is working. >>>>>>> The revision letter is printed near the network connector on top of >>>>>>> the board. For revC - try devicetree.dtb from the attachment. >>>>>>> >>>>>>> fix_net_config.tar.gz - just moves network configuration from >>>>>>> /etc/elphel393/init_elphel393.py to /etc/network/interfaces which is a >>>>>>> more >>>>>>> conventional place for linux. And it will be included in the next >>>>>>> release. >>>>>>> >>>>>>> I'm having trouble upgrading the NAND memory on an elphel 393. I've
Re: [Elphel-support] Elphel 393 Nand upgrade
Hi Mohamed, Does the board boot fine from flash? Does the same uSD card work with other rev B boards? On Thu, Dec 13, 2018 at 1:30 PM Mohamed Morsy wrote: > Hi Oleg, > > I'm having another issue with another Elphel. It doesn't seem to boot up > completely. When I connect the USB cable, open minicom, and power on the > Elphel, it starts booting up for 2 seconds then stops and minicom says > "Cannot open /dev/ttyUSB0!" The last thing on minicom before it stops is: > > [2.034545] elphel393-pwr elphel393-pwr@0: Probing elphel393-pwr > > This is a Rev B Elphel running on a uSD card. Do you know what the issue > might be? > > Thanks, > > Mohamed > > On Wed, Dec 5, 2018 at 9:48 AM Mohamed Morsy wrote: > >> That worked. Thanks. >> >> Mohamed >> >> On Tue, Dec 4, 2018 at 5:30 PM Oleg >> wrote: >> >>> Wrong file. My bad. Try this one. >>> >>> On Tue, Dec 4, 2018 at 3:17 PM Morsy, Mohamed K wrote: >>> >>>> Hi Oleg, >>>> >>>> >>>> I tried replacing the devicetree.dtb file in the nand folder from >>>> elphel393_20180511 >>>> with the one you sent. I tried the ipaddress/update_software.html tool >>>> again but nothing changed. When I log into the elphel from minicom and try >>>> ifconfig I still only get the local address at 127.0.0.1. This is on a Rev >>>> C board. Do you have any other ideas? >>>> >>>> >>>> Also I meant to send the previous email from my Redzone email so I'll >>>> CC myself to this chain. >>>> >>>> >>>> Thanks, >>>> >>>> >>>> Mohamed Morsy >>>> >>>> >>>> -- >>>> *From:* Oleg >>>> *Sent:* Tuesday, December 4, 2018 2:51 PM >>>> *To:* Morsy, Mohamed K >>>> *Cc:* elphel support-list >>>> *Subject:* Re: [Elphel-support] Elphel 393 Nand upgrade >>>> >>>> Hi Mohamed, >>>> >>>> I think it's not related. >>>> >>>> Most likely you need an updated device tree (devicetree.dtb). The >>>> newest boards are revC - they have a different PHY reg address compared to >>>> revB (and older). The recovery cards came with updated devicetree - and so, >>>> the network is working. >>>> The revision letter is printed near the network connector on top of the >>>> board. For revC - try devicetree.dtb from the attachment. >>>> >>>> fix_net_config.tar.gz - just moves network configuration from >>>> /etc/elphel393/init_elphel393.py to /etc/network/interfaces which is a more >>>> conventional place for linux. And it will be included in the next release. >>>> >>>> I'm having trouble upgrading the NAND memory on an elphel 393. I've >>>> tried it with multiple boards. I used the ipaddress/update_software.html >>>> tool. When I flash the board, I shut it down, remove the uSD card, and >>>> reboot it. But it doesn't boot up correctly. I'm able to log in on minicom >>>> but when I try ifconfig I find that the board doesn't have an ip address. >>>> Do you know how to resolve this issue? I noticed there's a recent upload at >>>> community.elphel.com/files/393 >>>> <https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fcommunity.elphel.com%2Ffiles%2F393=02%7C01%7CMKM89%40pitt.edu%7C69e9fd539853460af0b808d65a21ddbc%7C9ef9f489e0a04eeb87cc3a526112fd0d%7C1%7C1%7C63679549885600=nmNC%2B4fi8iv%2FKJk2i5mVpAEVZ4r1A5H%2FCS3woLV3%2Bhc%3D=0> >>>> called fix_net_config.tar.gz. Is that related to my issue? >>>> >>>> Thanks, >>>> Mohamed Morsy >>>> RedZone Robotics >>>> ___ >>>> Support-list mailing list >>>> Support-list@support.elphel.com >>>> >>>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com >>>> <https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fsupport.elphel.com%2Fmailman%2Flistinfo%2Fsupport-list_support.elphel.com=02%7C01%7CMKM89%40pitt.edu%7C69e9fd539853460af0b808d65a21ddbc%7C9ef9f489e0a04eeb87cc3a526112fd0d%7C1%7C1%7C636795498844455609=6WuAVJxImp03qJEMvMDpWa%2BCth%2BT%2B3t1bkmiWJ07tGE%3D=0> >>>> >>>> >>>> ___ >>>> Support-list mailing list >>>> Support-list@support.elphel.com >>>> >>>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com >>>> >>> >>> Best regards, >>> Oleg Dzhimiev >>> Electronics Engineer >>> phone: +1 801 783 x124 >>> Elphel, Inc. >>> >> ___ > Support-list mailing list > Support-list@support.elphel.com > http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com ___ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
Re: [Elphel-support] Elphel 393 Nand upgrade
No it does not boot from flash. The card does work with other boards. On Thu, Dec 13, 2018 at 3:46 PM Oleg wrote: > Hi Mohamed, > > Does the board boot fine from flash? > Does the same uSD card work with other rev B boards? > > On Thu, Dec 13, 2018 at 1:30 PM Mohamed Morsy wrote: > >> Hi Oleg, >> >> I'm having another issue with another Elphel. It doesn't seem to boot up >> completely. When I connect the USB cable, open minicom, and power on the >> Elphel, it starts booting up for 2 seconds then stops and minicom says >> "Cannot open /dev/ttyUSB0!" The last thing on minicom before it stops is: >> >> [2.034545] elphel393-pwr elphel393-pwr@0: Probing elphel393-pwr >> >> This is a Rev B Elphel running on a uSD card. Do you know what the issue >> might be? >> >> Thanks, >> >> Mohamed >> >> On Wed, Dec 5, 2018 at 9:48 AM Mohamed Morsy wrote: >> >>> That worked. Thanks. >>> >>> Mohamed >>> >>> On Tue, Dec 4, 2018 at 5:30 PM Oleg >>> wrote: >>> >>>> Wrong file. My bad. Try this one. >>>> >>>> On Tue, Dec 4, 2018 at 3:17 PM Morsy, Mohamed K wrote: >>>> >>>>> Hi Oleg, >>>>> >>>>> >>>>> I tried replacing the devicetree.dtb file in the nand folder from >>>>> elphel393_20180511 >>>>> with the one you sent. I tried the ipaddress/update_software.html >>>>> tool again but nothing changed. When I log into the elphel from minicom >>>>> and >>>>> try ifconfig I still only get the local address at 127.0.0.1. This is on a >>>>> Rev C board. Do you have any other ideas? >>>>> >>>>> >>>>> Also I meant to send the previous email from my Redzone email so I'll >>>>> CC myself to this chain. >>>>> >>>>> >>>>> Thanks, >>>>> >>>>> >>>>> Mohamed Morsy >>>>> >>>>> >>>>> -- >>>>> *From:* Oleg >>>>> *Sent:* Tuesday, December 4, 2018 2:51 PM >>>>> *To:* Morsy, Mohamed K >>>>> *Cc:* elphel support-list >>>>> *Subject:* Re: [Elphel-support] Elphel 393 Nand upgrade >>>>> >>>>> Hi Mohamed, >>>>> >>>>> I think it's not related. >>>>> >>>>> Most likely you need an updated device tree (devicetree.dtb). The >>>>> newest boards are revC - they have a different PHY reg address compared to >>>>> revB (and older). The recovery cards came with updated devicetree - and >>>>> so, >>>>> the network is working. >>>>> The revision letter is printed near the network connector on top of >>>>> the board. For revC - try devicetree.dtb from the attachment. >>>>> >>>>> fix_net_config.tar.gz - just moves network configuration from >>>>> /etc/elphel393/init_elphel393.py to /etc/network/interfaces which is a >>>>> more >>>>> conventional place for linux. And it will be included in the next release. >>>>> >>>>> I'm having trouble upgrading the NAND memory on an elphel 393. I've >>>>> tried it with multiple boards. I used the ipaddress/update_software.html >>>>> tool. When I flash the board, I shut it down, remove the uSD card, and >>>>> reboot it. But it doesn't boot up correctly. I'm able to log in on minicom >>>>> but when I try ifconfig I find that the board doesn't have an ip address. >>>>> Do you know how to resolve this issue? I noticed there's a recent upload >>>>> at >>>>> community.elphel.com/files/393 >>>>> <https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fcommunity.elphel.com%2Ffiles%2F393=02%7C01%7CMKM89%40pitt.edu%7C69e9fd539853460af0b808d65a21ddbc%7C9ef9f489e0a04eeb87cc3a526112fd0d%7C1%7C1%7C63679549885600=nmNC%2B4fi8iv%2FKJk2i5mVpAEVZ4r1A5H%2FCS3woLV3%2Bhc%3D=0> >>>>> called fix_net_config.tar.gz. Is that related to my issue? >>>>> >>>>> Thanks, >>>>> Mohamed Morsy >>>>> RedZone Robotics >>>>> ___ >>>>> Support-list mailing list >>>>> Support-list@support.elphel.com >>>>> >>>>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com >>>>> <https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fsupport.elphel.com%2Fmailman%2Flistinfo%2Fsupport-list_support.elphel.com=02%7C01%7CMKM89%40pitt.edu%7C69e9fd539853460af0b808d65a21ddbc%7C9ef9f489e0a04eeb87cc3a526112fd0d%7C1%7C1%7C636795498844455609=6WuAVJxImp03qJEMvMDpWa%2BCth%2BT%2B3t1bkmiWJ07tGE%3D=0> >>>>> >>>>> >>>>> ___ >>>>> Support-list mailing list >>>>> Support-list@support.elphel.com >>>>> >>>>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com >>>>> >>>> >>>> Best regards, >>>> Oleg Dzhimiev >>>> Electronics Engineer >>>> phone: +1 801 783 x124 >>>> Elphel, Inc. >>>> >>> ___ >> Support-list mailing list >> Support-list@support.elphel.com >> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com > > ___ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
Re: [Elphel-support] Elphel 393 Nand upgrade
Hi Oleg, I'm having another issue with another Elphel. It doesn't seem to boot up completely. When I connect the USB cable, open minicom, and power on the Elphel, it starts booting up for 2 seconds then stops and minicom says "Cannot open /dev/ttyUSB0!" The last thing on minicom before it stops is: [2.034545] elphel393-pwr elphel393-pwr@0: Probing elphel393-pwr This is a Rev B Elphel running on a uSD card. Do you know what the issue might be? Thanks, Mohamed On Wed, Dec 5, 2018 at 9:48 AM Mohamed Morsy wrote: > That worked. Thanks. > > Mohamed > > On Tue, Dec 4, 2018 at 5:30 PM Oleg > wrote: > >> Wrong file. My bad. Try this one. >> >> On Tue, Dec 4, 2018 at 3:17 PM Morsy, Mohamed K wrote: >> >>> Hi Oleg, >>> >>> >>> I tried replacing the devicetree.dtb file in the nand folder from >>> elphel393_20180511 >>> with the one you sent. I tried the ipaddress/update_software.html tool >>> again but nothing changed. When I log into the elphel from minicom and try >>> ifconfig I still only get the local address at 127.0.0.1. This is on a Rev >>> C board. Do you have any other ideas? >>> >>> >>> Also I meant to send the previous email from my Redzone email so I'll CC >>> myself to this chain. >>> >>> >>> Thanks, >>> >>> >>> Mohamed Morsy >>> >>> >>> -- >>> *From:* Oleg >>> *Sent:* Tuesday, December 4, 2018 2:51 PM >>> *To:* Morsy, Mohamed K >>> *Cc:* elphel support-list >>> *Subject:* Re: [Elphel-support] Elphel 393 Nand upgrade >>> >>> Hi Mohamed, >>> >>> I think it's not related. >>> >>> Most likely you need an updated device tree (devicetree.dtb). The newest >>> boards are revC - they have a different PHY reg address compared to revB >>> (and older). The recovery cards came with updated devicetree - and so, the >>> network is working. >>> The revision letter is printed near the network connector on top of the >>> board. For revC - try devicetree.dtb from the attachment. >>> >>> fix_net_config.tar.gz - just moves network configuration from >>> /etc/elphel393/init_elphel393.py to /etc/network/interfaces which is a more >>> conventional place for linux. And it will be included in the next release. >>> >>> I'm having trouble upgrading the NAND memory on an elphel 393. I've >>> tried it with multiple boards. I used the ipaddress/update_software.html >>> tool. When I flash the board, I shut it down, remove the uSD card, and >>> reboot it. But it doesn't boot up correctly. I'm able to log in on minicom >>> but when I try ifconfig I find that the board doesn't have an ip address. >>> Do you know how to resolve this issue? I noticed there's a recent upload at >>> community.elphel.com/files/393 >>> <https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fcommunity.elphel.com%2Ffiles%2F393=02%7C01%7CMKM89%40pitt.edu%7C69e9fd539853460af0b808d65a21ddbc%7C9ef9f489e0a04eeb87cc3a526112fd0d%7C1%7C1%7C63679549885600=nmNC%2B4fi8iv%2FKJk2i5mVpAEVZ4r1A5H%2FCS3woLV3%2Bhc%3D=0> >>> called fix_net_config.tar.gz. Is that related to my issue? >>> >>> Thanks, >>> Mohamed Morsy >>> RedZone Robotics >>> ___ >>> Support-list mailing list >>> Support-list@support.elphel.com >>> >>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com >>> <https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fsupport.elphel.com%2Fmailman%2Flistinfo%2Fsupport-list_support.elphel.com=02%7C01%7CMKM89%40pitt.edu%7C69e9fd539853460af0b808d65a21ddbc%7C9ef9f489e0a04eeb87cc3a526112fd0d%7C1%7C1%7C636795498844455609=6WuAVJxImp03qJEMvMDpWa%2BCth%2BT%2B3t1bkmiWJ07tGE%3D=0> >>> >>> >>> ___ >>> Support-list mailing list >>> Support-list@support.elphel.com >>> >>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com >>> >> >> Best regards, >> Oleg Dzhimiev >> Electronics Engineer >> phone: +1 801 783 x124 >> Elphel, Inc. >> > ___ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
Re: [Elphel-support] Elphel 393 Nand upgrade
That worked. Thanks. Mohamed On Tue, Dec 4, 2018 at 5:30 PM Oleg wrote: > Wrong file. My bad. Try this one. > > On Tue, Dec 4, 2018 at 3:17 PM Morsy, Mohamed K wrote: > >> Hi Oleg, >> >> >> I tried replacing the devicetree.dtb file in the nand folder from >> elphel393_20180511 >> with the one you sent. I tried the ipaddress/update_software.html tool >> again but nothing changed. When I log into the elphel from minicom and try >> ifconfig I still only get the local address at 127.0.0.1. This is on a Rev >> C board. Do you have any other ideas? >> >> >> Also I meant to send the previous email from my Redzone email so I'll CC >> myself to this chain. >> >> >> Thanks, >> >> >> Mohamed Morsy >> >> >> ---------- >> *From:* Oleg >> *Sent:* Tuesday, December 4, 2018 2:51 PM >> *To:* Morsy, Mohamed K >> *Cc:* elphel support-list >> *Subject:* Re: [Elphel-support] Elphel 393 Nand upgrade >> >> Hi Mohamed, >> >> I think it's not related. >> >> Most likely you need an updated device tree (devicetree.dtb). The newest >> boards are revC - they have a different PHY reg address compared to revB >> (and older). The recovery cards came with updated devicetree - and so, the >> network is working. >> The revision letter is printed near the network connector on top of the >> board. For revC - try devicetree.dtb from the attachment. >> >> fix_net_config.tar.gz - just moves network configuration from >> /etc/elphel393/init_elphel393.py to /etc/network/interfaces which is a more >> conventional place for linux. And it will be included in the next release. >> >> I'm having trouble upgrading the NAND memory on an elphel 393. I've tried >> it with multiple boards. I used the ipaddress/update_software.html tool. >> When I flash the board, I shut it down, remove the uSD card, and reboot it. >> But it doesn't boot up correctly. I'm able to log in on minicom but when I >> try ifconfig I find that the board doesn't have an ip address. Do you know >> how to resolve this issue? I noticed there's a recent upload at >> community.elphel.com/files/393 >> <https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fcommunity.elphel.com%2Ffiles%2F393=02%7C01%7CMKM89%40pitt.edu%7C69e9fd539853460af0b808d65a21ddbc%7C9ef9f489e0a04eeb87cc3a526112fd0d%7C1%7C1%7C63679549885600=nmNC%2B4fi8iv%2FKJk2i5mVpAEVZ4r1A5H%2FCS3woLV3%2Bhc%3D=0> >> called fix_net_config.tar.gz. Is that related to my issue? >> >> Thanks, >> Mohamed Morsy >> RedZone Robotics >> ___ >> Support-list mailing list >> Support-list@support.elphel.com >> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com >> <https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fsupport.elphel.com%2Fmailman%2Flistinfo%2Fsupport-list_support.elphel.com=02%7C01%7CMKM89%40pitt.edu%7C69e9fd539853460af0b808d65a21ddbc%7C9ef9f489e0a04eeb87cc3a526112fd0d%7C1%7C1%7C636795498844455609=6WuAVJxImp03qJEMvMDpWa%2BCth%2BT%2B3t1bkmiWJ07tGE%3D=0> >> >> >> ___ >> Support-list mailing list >> Support-list@support.elphel.com >> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com >> > > Best regards, > Oleg Dzhimiev > Electronics Engineer > phone: +1 801 783 x124 > Elphel, Inc. > ___ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
Re: [Elphel-support] Elphel 393 Nand upgrade
Wrong file. My bad. Try this one. On Tue, Dec 4, 2018 at 3:17 PM Morsy, Mohamed K wrote: > Hi Oleg, > > > I tried replacing the devicetree.dtb file in the nand folder from > elphel393_20180511 > with the one you sent. I tried the ipaddress/update_software.html tool > again but nothing changed. When I log into the elphel from minicom and try > ifconfig I still only get the local address at 127.0.0.1. This is on a Rev > C board. Do you have any other ideas? > > > Also I meant to send the previous email from my Redzone email so I'll CC > myself to this chain. > > > Thanks, > > > Mohamed Morsy > > > -- > *From:* Oleg > *Sent:* Tuesday, December 4, 2018 2:51 PM > *To:* Morsy, Mohamed K > *Cc:* elphel support-list > *Subject:* Re: [Elphel-support] Elphel 393 Nand upgrade > > Hi Mohamed, > > I think it's not related. > > Most likely you need an updated device tree (devicetree.dtb). The newest > boards are revC - they have a different PHY reg address compared to revB > (and older). The recovery cards came with updated devicetree - and so, the > network is working. > The revision letter is printed near the network connector on top of the > board. For revC - try devicetree.dtb from the attachment. > > fix_net_config.tar.gz - just moves network configuration from > /etc/elphel393/init_elphel393.py to /etc/network/interfaces which is a more > conventional place for linux. And it will be included in the next release. > > I'm having trouble upgrading the NAND memory on an elphel 393. I've tried > it with multiple boards. I used the ipaddress/update_software.html tool. > When I flash the board, I shut it down, remove the uSD card, and reboot it. > But it doesn't boot up correctly. I'm able to log in on minicom but when I > try ifconfig I find that the board doesn't have an ip address. Do you know > how to resolve this issue? I noticed there's a recent upload at > community.elphel.com/files/393 > <https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fcommunity.elphel.com%2Ffiles%2F393=02%7C01%7CMKM89%40pitt.edu%7C69e9fd539853460af0b808d65a21ddbc%7C9ef9f489e0a04eeb87cc3a526112fd0d%7C1%7C1%7C63679549885600=nmNC%2B4fi8iv%2FKJk2i5mVpAEVZ4r1A5H%2FCS3woLV3%2Bhc%3D=0> > called fix_net_config.tar.gz. Is that related to my issue? > > Thanks, > Mohamed Morsy > RedZone Robotics > ___ > Support-list mailing list > Support-list@support.elphel.com > http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com > <https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fsupport.elphel.com%2Fmailman%2Flistinfo%2Fsupport-list_support.elphel.com=02%7C01%7CMKM89%40pitt.edu%7C69e9fd539853460af0b808d65a21ddbc%7C9ef9f489e0a04eeb87cc3a526112fd0d%7C1%7C1%7C636795498844455609=6WuAVJxImp03qJEMvMDpWa%2BCth%2BT%2B3t1bkmiWJ07tGE%3D=0> > > > ___ > Support-list mailing list > Support-list@support.elphel.com > http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com > Best regards, Oleg Dzhimiev Electronics Engineer phone: +1 801 783 x124 Elphel, Inc. devicetree.dtb Description: Binary data ___ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
Re: [Elphel-support] Elphel 393 Nand upgrade
Hi Oleg, I tried replacing the devicetree.dtb file in the nand folder from elphel393_20180511 with the one you sent. I tried the ipaddress/update_software.html tool again but nothing changed. When I log into the elphel from minicom and try ifconfig I still only get the local address at 127.0.0.1. This is on a Rev C board. Do you have any other ideas? Also I meant to send the previous email from my Redzone email so I'll CC myself to this chain. Thanks, Mohamed Morsy From: Oleg Sent: Tuesday, December 4, 2018 2:51 PM To: Morsy, Mohamed K Cc: elphel support-list Subject: Re: [Elphel-support] Elphel 393 Nand upgrade Hi Mohamed, I think it's not related. Most likely you need an updated device tree (devicetree.dtb). The newest boards are revC - they have a different PHY reg address compared to revB (and older). The recovery cards came with updated devicetree - and so, the network is working. The revision letter is printed near the network connector on top of the board. For revC - try devicetree.dtb from the attachment. fix_net_config.tar.gz - just moves network configuration from /etc/elphel393/init_elphel393.py to /etc/network/interfaces which is a more conventional place for linux. And it will be included in the next release. I'm having trouble upgrading the NAND memory on an elphel 393. I've tried it with multiple boards. I used the ipaddress/update_software.html tool. When I flash the board, I shut it down, remove the uSD card, and reboot it. But it doesn't boot up correctly. I'm able to log in on minicom but when I try ifconfig I find that the board doesn't have an ip address. Do you know how to resolve this issue? I noticed there's a recent upload at community.elphel.com/files/393<https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fcommunity.elphel.com%2Ffiles%2F393=02%7C01%7CMKM89%40pitt.edu%7C69e9fd539853460af0b808d65a21ddbc%7C9ef9f489e0a04eeb87cc3a526112fd0d%7C1%7C1%7C63679549885600=nmNC%2B4fi8iv%2FKJk2i5mVpAEVZ4r1A5H%2FCS3woLV3%2Bhc%3D=0> called fix_net_config.tar.gz. Is that related to my issue? Thanks, Mohamed Morsy RedZone Robotics ___ Support-list mailing list Support-list@support.elphel.com<mailto:Support-list@support.elphel.com> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com<https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fsupport.elphel.com%2Fmailman%2Flistinfo%2Fsupport-list_support.elphel.com=02%7C01%7CMKM89%40pitt.edu%7C69e9fd539853460af0b808d65a21ddbc%7C9ef9f489e0a04eeb87cc3a526112fd0d%7C1%7C1%7C636795498844455609=6WuAVJxImp03qJEMvMDpWa%2BCth%2BT%2B3t1bkmiWJ07tGE%3D=0> ___ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
Re: [Elphel-support] Elphel 393 Nand upgrade
Hi Mohamed, I think it's not related. Most likely you need an updated device tree (devicetree.dtb). The newest boards are revC - they have a different PHY reg address compared to revB (and older). The recovery cards came with updated devicetree - and so, the network is working. The revision letter is printed near the network connector on top of the board. For revC - try devicetree.dtb from the attachment. fix_net_config.tar.gz - just moves network configuration from /etc/elphel393/init_elphel393.py to /etc/network/interfaces which is a more conventional place for linux. And it will be included in the next release. I'm having trouble upgrading the NAND memory on an elphel 393. I've tried > it with multiple boards. I used the ipaddress/update_software.html tool. > When I flash the board, I shut it down, remove the uSD card, and reboot it. > But it doesn't boot up correctly. I'm able to log in on minicom but when I > try ifconfig I find that the board doesn't have an ip address. Do you know > how to resolve this issue? I noticed there's a recent upload at > community.elphel.com/files/393 called fix_net_config.tar.gz. Is that > related to my issue? > > Thanks, > Mohamed Morsy > RedZone Robotics > ___ > Support-list mailing list > Support-list@support.elphel.com > http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com > devicetree.dtb Description: Binary data ___ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
