I replaced it with the 10385 board and now it works. Thanks. On Thu, Dec 13, 2018 at 4:21 PM Mohamed Morsy <mmo...@redzone.com> wrote:
> There are no sensors connected. I'm using direct 3.3V from a power supply. > I can try the 10385 board. > > On Thu, Dec 13, 2018 at 4:19 PM Oleg <support-list@support.elphel.com> > wrote: > >> This happens when the board tries to turn on 5V and fails. >> >> Try: >> * disconnect sensors if any connected >> * another power supply (how do you power the board? direct 3.3V or 48V >> via 10385 board?) >> * another power cable >> >> On Thu, Dec 13, 2018 at 1:50 PM Mohamed Morsy <mmo...@redzone.com> wrote: >> >>> No it does not boot from flash. >>> The card does work with other boards. >>> >>> On Thu, Dec 13, 2018 at 3:46 PM Oleg <support-list@support.elphel.com> >>> wrote: >>> >>>> Hi Mohamed, >>>> >>>> Does the board boot fine from flash? >>>> Does the same uSD card work with other rev B boards? >>>> >>>> On Thu, Dec 13, 2018 at 1:30 PM Mohamed Morsy <mmo...@redzone.com> >>>> wrote: >>>> >>>>> Hi Oleg, >>>>> >>>>> I'm having another issue with another Elphel. It doesn't seem to boot >>>>> up completely. When I connect the USB cable, open minicom, and power on >>>>> the >>>>> Elphel, it starts booting up for 2 seconds then stops and minicom says >>>>> "Cannot open /dev/ttyUSB0!" The last thing on minicom before it stops is: >>>>> >>>>> [ 2.034545] elphel393-pwr elphel393-pwr@0: Probing elphel393-pwr >>>>> >>>>> This is a Rev B Elphel running on a uSD card. Do you know what the >>>>> issue might be? >>>>> >>>>> Thanks, >>>>> >>>>> Mohamed >>>>> >>>>> On Wed, Dec 5, 2018 at 9:48 AM Mohamed Morsy <mmo...@redzone.com> >>>>> wrote: >>>>> >>>>>> That worked. Thanks. >>>>>> >>>>>> Mohamed >>>>>> >>>>>> On Tue, Dec 4, 2018 at 5:30 PM Oleg <support-list@support.elphel.com> >>>>>> wrote: >>>>>> >>>>>>> Wrong file. My bad. Try this one. >>>>>>> >>>>>>> On Tue, Dec 4, 2018 at 3:17 PM Morsy, Mohamed K <mk...@pitt.edu> >>>>>>> wrote: >>>>>>> >>>>>>>> Hi Oleg, >>>>>>>> >>>>>>>> >>>>>>>> I tried replacing the devicetree.dtb file in the nand folder from >>>>>>>> elphel393_20180511 >>>>>>>> with the one you sent. I tried the ipaddress/update_software.html >>>>>>>> tool again but nothing changed. When I log into the elphel from >>>>>>>> minicom and >>>>>>>> try ifconfig I still only get the local address at 127.0.0.1. This is >>>>>>>> on a >>>>>>>> Rev C board. Do you have any other ideas? >>>>>>>> >>>>>>>> >>>>>>>> Also I meant to send the previous email from my Redzone email so >>>>>>>> I'll CC myself to this chain. >>>>>>>> >>>>>>>> >>>>>>>> Thanks, >>>>>>>> >>>>>>>> >>>>>>>> Mohamed Morsy >>>>>>>> >>>>>>>> >>>>>>>> ------------------------------ >>>>>>>> *From:* Oleg <support-list@support.elphel.com> >>>>>>>> *Sent:* Tuesday, December 4, 2018 2:51 PM >>>>>>>> *To:* Morsy, Mohamed K >>>>>>>> *Cc:* elphel support-list >>>>>>>> *Subject:* Re: [Elphel-support] Elphel 393 Nand upgrade >>>>>>>> >>>>>>>> Hi Mohamed, >>>>>>>> >>>>>>>> I think it's not related. >>>>>>>> >>>>>>>> Most likely you need an updated device tree (devicetree.dtb). The >>>>>>>> newest boards are revC - they have a different PHY reg address >>>>>>>> compared to >>>>>>>> revB (and older). The recovery cards came with updated devicetree - >>>>>>>> and so, >>>>>>>> the network is working. >>>>>>>> The revision letter is printed near the network connector on top of >>>>>>>> the board. For revC - try devicetree.dtb from the attachment. >>>>>>>> >>>>>>>> fix_net_config.tar.gz - just moves network configuration from >>>>>>>> /etc/elphel393/init_elphel393.py to /etc/network/interfaces which is a >>>>>>>> more >>>>>>>> conventional place for linux. And it will be included in the next >>>>>>>> release. >>>>>>>> >>>>>>>> I'm having trouble upgrading the NAND memory on an elphel 393. I've >>>>>>>> tried it with multiple boards. I used the >>>>>>>> ipaddress/update_software.html >>>>>>>> tool. When I flash the board, I shut it down, remove the uSD card, and >>>>>>>> reboot it. But it doesn't boot up correctly. I'm able to log in on >>>>>>>> minicom >>>>>>>> but when I try ifconfig I find that the board doesn't have an ip >>>>>>>> address. >>>>>>>> Do you know how to resolve this issue? I noticed there's a recent >>>>>>>> upload at >>>>>>>> community.elphel.com/files/393 >>>>>>>> <https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fcommunity.elphel.com%2Ffiles%2F393&data=02%7C01%7CMKM89%40pitt.edu%7C69e9fd539853460af0b808d65a21ddbc%7C9ef9f489e0a04eeb87cc3a526112fd0d%7C1%7C1%7C636795498844445600&sdata=nmNC%2B4fi8iv%2FKJk2i5mVpAEVZ4r1A5H%2FCS3woLV3%2Bhc%3D&reserved=0> >>>>>>>> called fix_net_config.tar.gz. Is that related to my issue? >>>>>>>> >>>>>>>> Thanks, >>>>>>>> Mohamed Morsy >>>>>>>> RedZone Robotics >>>>>>>> _______________________________________________ >>>>>>>> Support-list mailing list >>>>>>>> Support-list@support.elphel.com >>>>>>>> >>>>>>>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com >>>>>>>> <https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fsupport.elphel.com%2Fmailman%2Flistinfo%2Fsupport-list_support.elphel.com&data=02%7C01%7CMKM89%40pitt.edu%7C69e9fd539853460af0b808d65a21ddbc%7C9ef9f489e0a04eeb87cc3a526112fd0d%7C1%7C1%7C636795498844455609&sdata=6WuAVJxImp03qJEMvMDpWa%2BCth%2BT%2B3t1bkmiWJ07tGE%3D&reserved=0> >>>>>>>> >>>>>>>> >>>>>>>> _______________________________________________ >>>>>>>> Support-list mailing list >>>>>>>> Support-list@support.elphel.com >>>>>>>> >>>>>>>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com >>>>>>>> >>>>>>> >>>>>>> Best regards, >>>>>>> Oleg Dzhimiev >>>>>>> Electronics Engineer >>>>>>> phone: +1 801 783 5555 x124 >>>>>>> Elphel, Inc. >>>>>>> >>>>>> _______________________________________________ >>>>> Support-list mailing list >>>>> Support-list@support.elphel.com >>>>> >>>>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com >>>> >>>> _______________________________________________ >>> Support-list mailing list >>> Support-list@support.elphel.com >>> >>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com >>> >> >>
_______________________________________________ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
