Hi, Oleg
I just tested the method 1. However, When I set the parameter TRIG_OUT =
0x00 and applied it, all the parameters could not save(Test it many times). So
I removed the external signal line, and tested all of these, it made works. The
frame num stopped growing.
Another question is that parameters can not be saved when I change the
trigger parameter(I remove the autoparameter*.* file in etc/elphel393), but
other parameters probably can be saved success. Can you have other suggestion?
________________________________
-----------------------------------------------------------
Best Regrad!
Yicheng-Zhang
Email: winston.zhang@bst<mailto:winston.zh...@blacksesame.com.cn>.ai
Tel: 18516291005
Black Sesame Technologies (Shanghai) Co., Ltd. www.bst.ai<http://www.bst.ai/>
Rm 1102-1108, Bldg36, No.2777, East Jinxiu Rd, Pudong District, Shanghai, China
发件人： Oleg<mailto:support-list@support.elphel.com>
发送时间： 2018-12-13 03:44
收件人： winston.zh...@bst.ai<mailto:winston.zh...@bst.ai>
抄送： david.zh...@bst.ai<mailto:david.zh...@bst.ai>;
qiao....@bst.ai<mailto:qiao....@bst.ai>;
tao.zh...@bst.ai<mailto:tao.zh...@bst.ai>; Qun
Gu<mailto:qun...@blacksesame.com>; elphel
support-list<mailto:support-list@support.elphel.com>
主题： Re: [Elphel-support] 答复: 答复: 答复: 答复: 答复: sync stereo with lidar
Hello,
In the link you used the internal trigger generator is working and is routed
out to the sync cable (which is probably self-looped - input and output wires
are connected):
Try:
1. Set TRIG_OUT=0x0 to stop internal pulses at the sync cable output:
# old link:
http://192.168.0.9/parsedit.php?sensor_port=0&immediate&TRIG_CONDITION=0x95555&TRIG_OUT=0x66555&TRIG_PERIOD=100000000&TRIG=4
# new link:
http://192.168.0.9/parsedit.php?sensor_port=0&immediate&TRIG_CONDITION=0x95555&TRIG_OUT=0x0&TRIG_PERIOD=100000000&TRIG=4
or
2. If the sync cable inputs and outputs connected. Disconnect the wires from
each other and apply your trigger source:
signal or "+" - to Black wire,
ground or "-" - to Green wire.
Please, check the wire colors and pinout
here<https://wiki.elphel.com/wiki/103891>.
Let us know if that worked. Thanks. I'll update our docs to make them clear.
Best regards,
Oleg Dzhimiev
Electronics Engineer
phone: +1 801 783 5555 x124
Elphel, Inc.
On Tue, Dec 11, 2018 at 9:04 PM Winston Zhang
<winston.zh...@bst.ai<mailto:winston.zh...@bst.ai>> wrote:
Hi, Andrey!
Thany you for your patience to answer our questions!
I have some new questions about external trigger. When I set the trigger
parameter as the page
http://192.168.0.9/parsedit.php?sensor_port=0&immediate&TRIG_CONDITION=0x95555&TRIG_OUT=0x66555&TRIG_PERIOD=10000000&TRIG=4,<http://192.168.0.9/parsedit.php?sensor_port=0&immediate&TRIG_CONDITION=0x95555&TRIG_OUT=0x66555&TRIG_PERIOD=100000000&TRIG=4,>
and I made the trigger board pulsing out the signal(10HZ), I found we could
get 10 images. But I stopped the trigger board signal, I also could update the
image(10hz). I wanted to konw that how can I test the external trigger signal
work? Because when i stop external source trigger signal, it could receive
images too.
________________________________
-----------------------------------------------------------
Best Regrad!
Yicheng-Zhang
Email: winston.zhang@bst<mailto:winston.zh...@blacksesame.com.cn>.ai
Tel: 18516291005
Black Sesame Technologies (Shanghai) Co., Ltd. www.bst.ai<http://www.bst.ai/>
Rm 1102-1108, Bldg36, No.2777, East Jinxiu Rd, Pudong District, Shanghai, China
发件人： Oleg<mailto:support-list@support.elphel.com>
发送时间： 2018-09-19 02:38
收件人： david.zh...@bst.ai<mailto:david.zh...@bst.ai>
抄送： winston.zh...@bst.ai<mailto:winston.zh...@bst.ai>;
tao.zh...@bst.ai<mailto:tao.zh...@bst.ai>; Qun
Gu<mailto:qun...@blacksesame.com>; elphel
support-list<mailto:support-list@support.elphel.com>
主题： Re: [Elphel-support] 答复: 答复: 答复: 答复: 答复: sync stereo with lidar
Hello,
Here are a couple commands (in linux) that can help to check and sync the
system clock:
- Compare PC and camera clock:
~$ ssh root@192.168.0.9<mailto:root@192.168.0.9> date;date -u
- Write PC time into camera clock:
~$ ssh root@192.168.0.9<mailto:root@192.168.0.9> "date -s @`( date -u +"%s" )`
&& hwclock -w"
After setting the system clock check if the time survives the reboot. If it
does not - then please update the firmware to
20180511<https://wiki.elphel.com/wiki/10393_manual#Firmware.2Fsoftware_update>.
There was a bug in the clock driver we had to fix a while ago.
Regards,
Oleg
On Mon, Sep 17, 2018 at 11:27 PM David Zhang
<david.zh...@bst.ai<mailto:david.zh...@bst.ai>> wrote:
Hi, Andrey,
We use default configuration(TRIG=4 and TRIG_PERIOD=25000000). Is that OK? And
now our situation is there are timestamps in EXIF header. But it is not
the kernel's system time.
e.g. the timestamp in EXIF may be 2018/09/14 but actually system's date is
2018/09/18.
How can i fix it? Thanks.
Best,
David
________________________________
发件人: Elphel Support
<support-list@support.elphel.com<mailto:support-list@support.elphel.com>>
发送时间: 2018年9月18日 10:03:19
收件人: Winston Zhang
抄送: Winston Zhang; Tao Zhang; Qun Gu; David Zhang
主题: Re: [Elphel-support] 答复: 答复: 答复: 答复: sync stereo with lidar
Winston,
What trigger settings do you use ( https://wiki.elphel.com/wiki/Trigger_393 )?
Trigger 393 - ElphelWiki -
wiki.elphel.com<https://wiki.elphel.com/wiki/Trigger_393>
wiki.elphel.com<http://wiki.elphel.com>
Description. 10389 board is required. The triggering is used for one or several
cameras synchronization or setting the frame rate (or fps). The conditions of
the trigger can be generated either internally or externally.
Camera channels should be in triggered mode (TRIG=4) and have correct
TRIG_PERIOD. Then all channels will be exactly synchronized. If you set
TRIG_PERIOD to some "even" number (like exactly 10fps with
TRIG_PERIOD=10000000), then timestamps will have all digits but seconds and
tenths of a second the same for all frames.
Andrey
---- On Mon, 17 Sep 2018 18:31:26 -0700
<winston.zh...@bst.ai<mailto:winston.zh...@bst.ai>> wrote ----
Hi, Andrey!
I captured some images form camera with the timestamp image name. This
timestamp was the same with camera system timestamp. And the other way, each
image had its exif information that contained the real timestamp. But this
timestamp from exif information was not the same with system timestamp. So can
you provided some detials about where was the exif timestamp from. And how did
i do can solve this problem.
(i had synchronized the camera system time with the GPS timestamp.)
________________________________
-----------------------------------------------------------
Best Regrad!
Yicheng-Zhang
Email: winston.zhang@bst<mailto:winston.zh...@blacksesame.com.cn>.ai
Tel: 18516291005
Addr: 707 room, 7th floor, building 4th, No.1761, Zhangdong road, Pudong area
发件人： Oleg<mailto:support-list@support.elphel.com>
发送时间： 2018-05-12 06:32
收件人： Winston Zhang<mailto:winston.zh...@blacksesame.com.cn>
抄送： Tao Zhang<mailto:tao.zh...@blacksesame.com.cn>; Qun
Gu<mailto:qun...@blacksesame.com>; David
Zhang<mailto:david.zh...@blacksesame.com.cn>; elphel
support-list<mailto:support-list@support.elphel.com>
主题： Re: [Elphel-support] 答复: 答复: 答复: 答复: sync stereo with lidar
Winston,
I could get the info from the 192.168.0.9:2323<http://192.168.0.9:2323>. This
web could help me to get some information. But if I tried the
http://192.168.0.9:2323/timestamp_name, the timestamp file saved web did not
appear. How did I use it?
http://192.168.0.9:2323/pointer_value/img
Try the following:
1. get
diagnostics.php<https://git.elphel.com/Elphel/elphel-web-393/blob/master/src/diagnostics/diagnostics.php>
2. copy to 192.168.0.9:/www/pages/
3. In the browser open:
view-source:http://192.168.0.9/diagnostics.php?pointers
You will get xml output similar to this one:
<?xml version='1.0' standalone='yes'?>
<Document>
<camera ip='192.168.0.9'>
<port index='0' sensor='mt9p006, none, none, none' mux='none'>
<timestamps>
...
<ts frame='7290' ts='1526075540.347616'
ptr='pointer_value'>1526075540.347616</ts>
...
Take the pointer_value from the last <ts> for a particular port. Don't forget
to add "/img" or "/bimg".
If something does not work. Please send me your xml.
Best regards,
Oleg Dzhimiev
Electronics Engineer
phone: +1 801 783 5555 x124
Elphel, Inc.
_______________________________________________
Support-list mailing list
Support-list@support.elphel.com<mailto:Support-list@support.elphel.com>
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
_______________________________________________
Support-list mailing list
Support-list@support.elphel.com<mailto:Support-list@support.elphel.com>
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
_______________________________________________
Support-list mailing list
Support-list@support.elphel.com<mailto:Support-list@support.elphel.com>
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
_______________________________________________
Support-list mailing list
Support-list@support.elphel.com
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
