After you remove the fan from the bottom of the camera (two M2.5 screws) you
need to remove 8 (4+4) screws from the front and back panel. Then remove front
one and push boards with the heat plate (boards are attached to it) pushing on
the heat plate (you may make some simple tool to push on that plate). When
pushing - be careful with the SSD not to hit the camera tripod mount part as it
becomes loos when you remove the fan.
When you will be reassembling the camera - I put the back panel on the
assembled boards first, and then slide them together into the camera body,
making sure that a micro-USB connector does not hit the back panel (otherwise
it can be easily peeled off the PCB).
And yes - camera does not see port 1. It is more likely the PCB, not the cable
problem - I do not see how the cable can fail gradually:
from autocampars.log
...
00037.35 autocampars: All frames:
sensor_fram16 0x2 0x0 0x0 0x0
compressor_fram16 0x0 0x0 0x0 0x0
i2c_frame16 0x2 0x0 0x0 0x0
sensor_aframe 0x00000002 0x00000000 0x00000000 0x00000000
compressor_aframe 0x00000000 0x00000000 0x00000000 0x00000000
compressor_gframe 0x00000000 0x00000000 0x00000000 0x00000000
00037.36 autocampars: Frames: 0, 0, 0, 0
00037.37 autocampars: #### Wrong/missing sensor on port 1, code=0 (expected 52)
. Driver reports errors until port is disabled at later stage ####
00037.38 autocampars: #### Wrong/missing sensor on port 2, code=0 (expected 52)
. Driver reports errors until port is disabled at later stage ####
00037.39 autocampars: #### Wrong/missing sensor on port 3, code=0 (expected 52)
. Driver reports errors until port is disabled at later stage ####
00037.40 autocampars: port=0 GLOBALS[sensors][port][0]=mt9p006
00037.41 autocampars: port=1 GLOBALS[sensors][port][0]=none
00037.42 autocampars: port=2 GLOBALS[sensors][port][0]=none
00037.43 autocampars: port=3 GLOBALS[sensors][port][0]=none
...
Andrey
---- On Sun, 27 Feb 2022 17:50:35 -0700 Elphel Support
<support-list@support.elphel.com> wrote ----
Norman,
If it is not too late - you need to take off fan first, then slide out the
boards of the camera. Fan has a long connector reaching to the board through
the hole.
Andrey
---- On Sun, 27 Feb 2022 16:59:41 -0700 XIONG, Norman
<mailto:n...@ansto.gov.au> wrote ----
Hi, Andrey,
Thanks for the quick response.
Here are the two log files, with both ports connected with sensors. I'll try to
open up the box to reconnect the cable shortly.
Regards,
Norman
From: Elphel Support <mailto:support-list@support.elphel.com>
Sent: 28 February 2022 10:19 AM
To: XIONG, Norman <mailto:n...@ansto.gov.au>
Subject: Re: [Elphel-support] Help on possible faulty FPC cable [SEC=OFFICIAL]
CAUTION, EXTERNAL EMAIL: This message has come from a source outside of ANSTO.
Do not take action, click links or open attachments unless
you recognise and trust the source of this email and know the content is safe.
Please report suspicious emails to as an attachment.
Hello Norman,
Can you get log files from the camera?
>From Linux system
ssh-copy-id root@192.168.0.9 # Or whatever IP is assigned to the camera
default password is pass
Then you can use scp to copy files to your local directory:
scp root@192.168.0.9:/var/log/messages
scp root@192.168.0.9:/var/log/autocampars.log
Abd then send these files.
Yes, we will prepare the new camera, but in any case I would like to try to
troubleshoot the camera you have, if that will not work we will send you a
replacement one. You may try to open the camera and get access to the camera
side of the cable. Camera
has 4 cable ports so you may try to either just reconnect the cable or try
other port.
The gold-plated pins on the cable end should be towards the connector lock.
When you try different port, the image can be corrupted (delays fro the long
cable were set only for ports 0 and 1.
Andrey
---- On Sun, 27 Feb 2022 15:57:50 -0700 XIONG, Norman
<mailto:n...@ansto.gov.au> wrote ----
Hi, Andrey,
I am not able to get port 1 back. When I connected both ports, I got only one
sensor image on port 0. And if I connect only port 1, the system can't find any
sensor.
Anyway, we decided to buy another 393 system to support the second sensor. This
is mainly because we need to put the two sensors far away from each other,
where the FPC cables are not long enough to connect both sensors to the same
system.
Enclosed is our previous order invoice. We want to duplicate the NC393 system,
but no sensor or lens is rquired. We need one 450mm FPC cable pre-cofigured for
the system, and a PoE power supply. Can you please ask your sales team to
provide me with a new quote?
Thank you.
Regards,
Dr Norman Xiong
Scientific Software Engineer
Australian
Centre for Neutron Scattering
Australian Nuclear Science and Technology Organisation
Tel
Email
Web
+61 2 9717 7008
https://exchnlb-b51.ansto.gov.au/owa/redir.aspx?C=d49cfec1ed6d483489b2b97e6981cdd1&URL=mailto%3aNORMAN.XIONG%40ansto.gov.au
https://exchnlb-b51.ansto.gov.au/owa/redir.aspx?C=d49cfec1ed6d483489b2b97e6981cdd1&URL=http%3a%2f%2fwww.ansto.gov.au%2f
Important: This transmission is intended only for the use of the intended
addressee.
It is confidential to the intended addressee and may contain privileged
information and or copyright material. If this email is not intended for your
attention, any use, printing, storage , reproduction or further disclosure of
this communication (including
all attachments) is strictly forbidden. If you have received this transmission
in error, please notify me by telephone or email and immediately delete all
copies of this transmission as well as any attachments.
From: Elphel Support <mailto:support-list@support.elphel.com>
Sent: 27 February 2022 6:14 AM
To: XIONG, Norman <mailto:n...@ansto.gov.au>; Elphel List
<mailto:support-list@support.elphel.com>
Subject: Re: [Elphel-support] Help on possible faulty FPC cable [SEC=OFFICIAL]
CAUTION, EXTERNAL EMAIL: This message has come from a source outside of ANSTO.
Do
not take action, click links or open attachments unless you recognise and
trust the source of this email and know the content is safe. Please report
suspicious emails to as an attachment.
Hello Norman,
I'm sorry you are having these problems. 450mm cables are close to the maximal
usable length. Most likely the problem is related to the need to change delay
in the sensor interface signals relative to clock, not the hardware problem
with the cable. But
it still can be the problem, of course.
What happens now - you can get a picture from port 0, and nothing at all on
port 1? Black image, corrupted image, getting stuck trying to get an image?
What happened before (when it was restoring after reboot)?
If you are getting corrupted image - can you please send it ?
Andrey
---- On Wed, 23 Feb 2022 02:46:52 -0700 XIONG, Norman
<mailto:n...@ansto.gov.au> wrote ----
Dear Elphel support team,
We have a NC393 system, with two sensors connected by 450mm FPC cables. Ever
since
we put the system together in last July, port 1 was unstable and lost connection
every a few
weeks. Rebooting the system would get the port back. However, recently that port
was
totally lost. We can’t have it back by rebooting or reconnecting the camera to
the cable.
We did a simple debugging by swapping sensors between the two FPC cables. Both
sensors
worked with port 0, and neither of them worked with port 1. So we presume the
FPC
cable
on port 1 is faulty. We didn’t open up the box to check the connection between
the cable and
the board. I am looking for advice on what I should do next. Shall I open up the
box to check
the internal connection or shall I simply order another FPC cable from you? And
Is the cable
fragile?
Thanks.
Regards,
Norman
Xiong
Software
Engineer (Scientific)
NSTLI Neutron Scattering
Tel
Email
Web
+61
2 9717 7008
mailto:n...@ansto.gov.au
http://www.ansto.gov.au/
http://www.facebook.com/DiscoverANSTO https://twitter.com/ANSTO
http://www.linkedin.com/company/ansto http://www.youtube.com/user/ANSTOVideos
Important:This transmission is intended only for the use of the intended
addressee.
It is confidential to the intended addressee and may contain privileged
information and or copyright material. If this email is not intended for your
attention, any use, printing, storage, reproduction or further disclosure of
this communication (including
all attachments) is strictly forbidden. If you have received this transmission
in error, please notify me by telephone or email and immediately delete all
copies of this transmission as well as any attachments.
OFFICIAL
_______________________________________________
Support-list mailing list
mailto:Support-list@support.elphel.com
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
_______________________________________________
Support-list mailing list
mailto:Support-list@support.elphel.com
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
_______________________________________________
Support-list mailing list
mailto:Support-list@support.elphel.com
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
_______________________________________________
Support-list mailing list
Support-list@support.elphel.com
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
