They can ping the WAN public, but not the next hop. Thank you, Brett A Mansfield
> On Jun 9, 2015, at 9:40 PM, Josh Luthman <[email protected]> wrote: > > Can the devices on publics ping the WAN public? Next hop up? > > Josh Luthman > Office: 937-552-2340 > Direct: 937-552-2343 > 1100 Wayne St > Suite 1337 > Troy, OH 45373 > >> On Jun 9, 2015 11:39 PM, "Brett A Mansfield" <[email protected]> >> wrote: >> All UBNT. Almost every model XM and XW and a few dozen of their AC line. >> >> Thank you, >> Brett A Mansfield >> >>> On Jun 9, 2015, at 9:31 PM, George Skorup <[email protected]> wrote: >>> >>> What radios? >>> >>>> On 6/9/2015 9:44 PM, Brett A Mansfield wrote: >>>> The public is on bridge1. VLAN 100 is a layer on top of bridge1. So public >>>> is not tagged and VLAN 100 is, both on bridge1. I have each CPE getting an >>>> IP address on VLAN 100 and bridging the public to the customers router. >>>> >>>> Thank you, >>>> Brett A Mansfield >>>> >>>> On Jun 9, 2015, at 8:39 PM, Josh Luthman <[email protected]> >>>> wrote: >>>> >>>>> Is 192.168.100.1 and 108.165.x.x both on the vlan interface? Or one >>>>> bridge1 and one vlan100? >>>>> >>>>> >>>>> Josh Luthman >>>>> Office: 937-552-2340 >>>>> Direct: 937-552-2343 >>>>> 1100 Wayne St >>>>> Suite 1337 >>>>> Troy, OH 45373 >>>>> >>>>>> On Tue, Jun 9, 2015 at 10:36 PM, Brett A Mansfield >>>>>> <[email protected]> wrote: >>>>>> The public IPs are not on a VLAN. The subnet is 108.165.x.0/24. >>>>>> >>>>>> I currently have eth1-eth7 bridged. Bridge1 is where I have the public >>>>>> IPs. Bridge1 VLAN 100 is the private IPs of 192.168.100.0/24. I don't >>>>>> use the SFP+ ports yet. Eth8 is the internet port. It has an IP address >>>>>> of 108.165.x.246/30. I currently have this confit on an UBNT edgerouter >>>>>> and it works flawlessly other than the random panics of the OS. The >>>>>> local public subnet is routed. >>>>>> >>>>>> Thank you, >>>>>> Brett A Mansfield >>>>>> >>>>>> On Jun 9, 2015, at 8:29 PM, Josh Luthman <[email protected]> >>>>>> wrote: >>>>>> >>>>>>> Are the public IPs on the VLAN 100 interface? >>>>>>> >>>>>>> Need some configuration here. What are the device's IPs/subnets? What >>>>>>> is the Mikrotik's LAN/vlan100 IP/subnet? What about WAN? Is the local >>>>>>> "LAN" public subnet routed to the rest of the world? >>>>>>> >>>>>>> >>>>>>> Josh Luthman >>>>>>> Office: 937-552-2340 >>>>>>> Direct: 937-552-2343 >>>>>>> 1100 Wayne St >>>>>>> Suite 1337 >>>>>>> Troy, OH 45373 >>>>>>> >>>>>>> On Tue, Jun 9, 2015 at 10:27 PM, Brett A Mansfield >>>>>>> <[email protected]> wrote: >>>>>>>> I am fairly new to Mikrotik and I cannot get it to do what I want. I >>>>>>>> have the CCR1036-8G-2S+. I have one VLAN using private IPs. It’s >>>>>>>> VLAN 100. I also have a /24 subnet of public IPs. I have NAT setup >>>>>>>> for the VLAN because it does need internet access. I have no NAT on >>>>>>>> the untagged VLAN of public IPs. I can access the net using VLAN 100, >>>>>>>> but not the public IPs. Anyone else run into this or have any ideas >>>>>>>> or thoughts? >>>>>>>> >>>>>>>> I’ve tried both Static and Dynamic IPs. I have NOT tried to removing >>>>>>>> the VLAN 100 yet. I will give that a shot later today. I do not have >>>>>>>> any kind of firewall on here just yet. >>>>>>>> >>>>>>>> Thank you, >>>>>>>> Brett A Mansfield >>>>>>>> Silver Lake Internet, LLC
