That one uses the same screws as the fan.
Google Hoffman AFLT44. It's $32 on Allied Electric, but half that from
our local electrical supply store.
The filter just slides into a slot, buy one spare. Swap them around and
put the dirty one in the dishwasher.
On 4/21/2016 1:02 AM, That One Guy /sarcasm wrote:
where does that filter fit? filters have been killing me, making them
idiot replaceable in the field
On Thu, Apr 21, 2016 at 12:02 AM, Scott Vander Dussen
<[email protected] <mailto:[email protected]>> wrote:
Awesome, thank you. I ordered one of the RG-11 Rain Sensors which
has a 24v 1A relay on it and am going to try that out as well. We
have a door sensor attached to the site monitor now, could I use
that to trigger the site monitor relay? To turn on some 24vdc LED
lights inside the enclosure when the door opens?
*From:*Af [mailto:[email protected]
<mailto:[email protected]>] *On Behalf Of *Forrest Christian
(List Account)
*Sent:* Wednesday, April 20, 2016 21:22
*To:* af <[email protected] <mailto:[email protected]>>
*Subject:* Re: [AFMUG] Enclosure ventilation
The relay on the base unit is more than large enough to turn on
and off that fan - at 24V it can switch 2A. You just run power
from your power source into the 'c' terminal, and then from the
'n.o' terminal to the fan. Hook the black back to the power source.
If you just want temperature control, there are two values you can
set which say 'relay on above' and 'relay on below' which will
allow you set the relay to turn on/off with temperature control.
I'd just set 'relay on above' to something like '200', which means
turn the fan on over 20*C (about room temperature). If this
doesn't work, let me know and I'll get you the correct firmware
for that (there was a bug which we fixed, but I'm not sure where
it is in the whole release/shipping/on website process).
-forrest
On Wed, Apr 20, 2016 at 9:28 PM, Scott Vander Dussen
<[email protected] <mailto:[email protected]>> wrote:
Fiberglass enclosure
Bud Industries
IPV-1116<http://www.alliedelec.com/bud-industries-ipv-1116/70368864/>
vents
Orion
WMG60M<http://www.alliedelec.com/orion-knight-electronics-inc-wmg60m/70103693/>
wire filters
60mm DC
fan<http://www.rpelectronics.com/cfa246025ms-24vdc-sleeve-bearing-60mm-fan.html>
with Locked Rotor Alarm Signal Output
60mm
guard<http://www.rpelectronics.com/cfg-60m-60mm-metal-finger-guard.html>
The enclosure includes a Site Monitor, I'm hoping to use its
secondary DC input to monitor the fan's yellow alarm wire lead
and trigger an error state in our SNMP monitoring if a fan
becomes locked.
I'm concerned about the fans running 24x7 potentially bringing
in moisture from fog/nightly humidity. With the site monitor
could to turn the fans on/off based upon ambient temperature
or time of day? If yes, how would I do that, a relay? What
kind of relay? I don't have much experience with relays/Site
Monitors, thanks. Or is there some other obvious solution I'm
missing?
Another idea is to use a Hyderon RG-11 Rain Sensor /
Gauge<http://rainsensors.com/how-it-works/> to trigger the
fans off for both dark (less than 2000 lux) and/or rain. This
seems pretty rad!
Thanks,
`S
--
*Forrest Christian*/CEO, PacketFlux Technologies, Inc./
Tel: 406-449-3345 <tel:406-449-3345> | Address: 3577 Countryside
Road, Helena, MT 59602
[email protected] <mailto:[email protected]> |
http://www.packetflux.com <http://www.packetflux.com/>
<http://www.linkedin.com/in/fwchristian>
<http://facebook.com/packetflux> <http://twitter.com/@packetflux>
--
If you only see yourself as part of the team but you don't see your
team as part of yourself you have already failed as part of the team.
